This is a note to let you know that I've just added the patch titled
net: hns3: using user configure after hardware reset
to the 6.6-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
net-hns3-using-user-configure-after-hardware-reset.patch
and it can be found in the queue-6.6 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
commit 7b6941f7507a8e8f8f5fcbd64d72441e403a6ac9
Author: Peiyang Wang <wangpeiyang1@xxxxxxxxxx>
Date: Tue May 7 21:42:18 2024 +0800
net: hns3: using user configure after hardware reset
[ Upstream commit 05eb60e9648cca0beeebdbcd263b599fb58aee48 ]
When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.
The specific process is as follows:
+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v
To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@xxxxxxxxxx>
Signed-off-by: Jijie Shao <shaojijie@xxxxxxxxxx>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@xxxxxxxxx>
Reviewed-by: Simon Horman <horms@xxxxxxxxxx>
Signed-off-by: Paolo Abeni <pabeni@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index dfd0c5f4cb9f5..4398de42c9157 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -1526,6 +1526,9 @@ static int hclge_configure(struct hclge_dev *hdev)
cfg.default_speed, ret);
return ret;
}
+ hdev->hw.mac.req_speed = hdev->hw.mac.speed;
+ hdev->hw.mac.req_autoneg = AUTONEG_ENABLE;
+ hdev->hw.mac.req_duplex = DUPLEX_FULL;
hclge_parse_link_mode(hdev, cfg.speed_ability);
@@ -3331,9 +3334,9 @@ hclge_set_phy_link_ksettings(struct hnae3_handle *handle,
return ret;
}
- hdev->hw.mac.autoneg = cmd->base.autoneg;
- hdev->hw.mac.speed = cmd->base.speed;
- hdev->hw.mac.duplex = cmd->base.duplex;
+ hdev->hw.mac.req_autoneg = cmd->base.autoneg;
+ hdev->hw.mac.req_speed = cmd->base.speed;
+ hdev->hw.mac.req_duplex = cmd->base.duplex;
linkmode_copy(hdev->hw.mac.advertising, cmd->link_modes.advertising);
return 0;
@@ -3366,9 +3369,9 @@ static int hclge_tp_port_init(struct hclge_dev *hdev)
if (!hnae3_dev_phy_imp_supported(hdev))
return 0;
- cmd.base.autoneg = hdev->hw.mac.autoneg;
- cmd.base.speed = hdev->hw.mac.speed;
- cmd.base.duplex = hdev->hw.mac.duplex;
+ cmd.base.autoneg = hdev->hw.mac.req_autoneg;
+ cmd.base.speed = hdev->hw.mac.req_speed;
+ cmd.base.duplex = hdev->hw.mac.req_duplex;
linkmode_copy(cmd.link_modes.advertising, hdev->hw.mac.advertising);
return hclge_set_phy_link_ksettings(&hdev->vport->nic, &cmd);
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
index 7bc2049b723da..6a6b41ef08baf 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
@@ -263,11 +263,14 @@ struct hclge_mac {
u8 media_type; /* port media type, e.g. fibre/copper/backplane */
u8 mac_addr[ETH_ALEN];
u8 autoneg;
+ u8 req_autoneg;
u8 duplex;
+ u8 req_duplex;
u8 support_autoneg;
u8 speed_type; /* 0: sfp speed, 1: active speed */
u8 lane_num;
u32 speed;
+ u32 req_speed;
u32 max_speed;
u32 speed_ability; /* speed ability supported by current media */
u32 module_type; /* sub media type, e.g. kr/cr/sr/lr */
