This is a note to let you know that I've just added the patch titled
spi: imx: move wml setting to later than setup_transfer
to the 4.19-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
spi-imx-move-wml-setting-to-later-than-setup_transfe.patch
and it can be found in the queue-4.19 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
commit 0391ed229fc995b3d20f5062507b3b4f20a59e83
Author: Robin Gong <yibin.gong@xxxxxxx>
Date: Wed Oct 10 10:32:42 2018 +0000
spi: imx: move wml setting to later than setup_transfer
[ Upstream commit 987a2dfe3f0485a82d87106e7e1c43f35c1d3b09 ]
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@xxxxxxx>
Signed-off-by: Mark Brown <broonie@xxxxxxxxxx>
Stable-dep-of: 00b80ac93553 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index eb27f47578eb9..686251e05edfe 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -64,6 +64,7 @@ struct spi_imx_devtype_data {
void (*trigger)(struct spi_imx_data *);
int (*rx_available)(struct spi_imx_data *);
void (*reset)(struct spi_imx_data *);
+ void (*setup_wml)(struct spi_imx_data *);
void (*disable)(struct spi_imx_data *);
bool has_dmamode;
bool has_slavemode;
@@ -601,6 +602,11 @@ static int mx51_ecspi_config(struct spi_device *spi)
else /* SCLK is _very_ slow */
usleep_range(delay, delay + 10);
+ return 0;
+}
+
+static void mx51_setup_wml(struct spi_imx_data *spi_imx)
+{
/*
* Configure the DMA register: setup the watermark
* and enable DMA request.
@@ -611,8 +617,6 @@ static int mx51_ecspi_config(struct spi_device *spi)
MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
-
- return 0;
}
static int mx51_ecspi_rx_available(struct spi_imx_data *spi_imx)
@@ -973,6 +977,7 @@ static struct spi_imx_devtype_data imx51_ecspi_devtype_data = {
.trigger = mx51_ecspi_trigger,
.rx_available = mx51_ecspi_rx_available,
.reset = mx51_ecspi_reset,
+ .setup_wml = mx51_setup_wml,
.fifo_size = 64,
.has_dmamode = true,
.dynamic_burst = true,
@@ -1181,7 +1186,6 @@ static int spi_imx_setupxfer(struct spi_device *spi,
struct spi_transfer *t)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
- int ret;
if (!t)
return 0;
@@ -1222,12 +1226,6 @@ static int spi_imx_setupxfer(struct spi_device *spi,
else
spi_imx->usedma = 0;
- if (spi_imx->usedma) {
- ret = spi_imx_dma_configure(spi->master);
- if (ret)
- return ret;
- }
-
if (is_imx53_ecspi(spi_imx) && spi_imx->slave_mode) {
spi_imx->rx = mx53_ecspi_rx_slave;
spi_imx->tx = mx53_ecspi_tx_slave;
@@ -1332,6 +1330,13 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
unsigned long timeout;
struct spi_master *master = spi_imx->bitbang.master;
struct sg_table *tx = &transfer->tx_sg, *rx = &transfer->rx_sg;
+ int ret;
+
+ ret = spi_imx_dma_configure(master);
+ if (ret)
+ return ret;
+
+ spi_imx->devtype_data->setup_wml(spi_imx);
/*
* The TX DMA setup starts the transfer, so make sure RX is configured
