This is a note to let you know that I've just added the patch titled
media: i2c: ov5640: Configure HVP lines in s_power callback
to the 5.4-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
media-i2c-ov5640-configure-hvp-lines-in-s_power-call.patch
and it can be found in the queue-5.4 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
commit 3947d3fec76ca7e843e877abcf649169ad206af5
Author: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
Date: Fri Sep 4 22:18:33 2020 +0200
media: i2c: ov5640: Configure HVP lines in s_power callback
[ Upstream commit 311a6408f8d46d47e35d3bf598dced39af4ce087 ]
Configure HVP lines in s_power callback instead of configuring everytime
in ov5640_set_stream_dvp().
Alongside also disable MIPI in DVP mode.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
Tested-by: Jacopo Mondi <jacopo@xxxxxxxxxx>
Signed-off-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
Stable-dep-of: 98cb72d3b9c5 ("media: ov5640: Enable MIPI interface in ov5640_set_power_mipi()")
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
index 087fb464ffc12..76a9fa6d6d5c0 100644
--- a/drivers/media/i2c/ov5640.c
+++ b/drivers/media/i2c/ov5640.c
@@ -1206,71 +1206,6 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on)
static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on)
{
- int ret;
- unsigned int flags = sensor->ep.bus.parallel.flags;
- u8 pclk_pol = 0;
- u8 hsync_pol = 0;
- u8 vsync_pol = 0;
-
- /*
- * Note about parallel port configuration.
- *
- * When configured in parallel mode, the OV5640 will
- * output 10 bits data on DVP data lines [9:0].
- * If only 8 bits data are wanted, the 8 bits data lines
- * of the camera interface must be physically connected
- * on the DVP data lines [9:2].
- *
- * Control lines polarity can be configured through
- * devicetree endpoint control lines properties.
- * If no endpoint control lines properties are set,
- * polarity will be as below:
- * - VSYNC: active high
- * - HREF: active low
- * - PCLK: active low
- */
-
- if (on) {
- /*
- * configure parallel port control lines polarity
- *
- * POLARITY CTRL0
- * - [5]: PCLK polarity (0: active low, 1: active high)
- * - [1]: HREF polarity (0: active low, 1: active high)
- * - [0]: VSYNC polarity (mismatch here between
- * datasheet and hardware, 0 is active high
- * and 1 is active low...)
- */
- if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
- pclk_pol = 1;
- if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
- hsync_pol = 1;
- if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
- vsync_pol = 1;
-
- ret = ov5640_write_reg(sensor,
- OV5640_REG_POLARITY_CTRL00,
- (pclk_pol << 5) |
- (hsync_pol << 1) |
- vsync_pol);
-
- if (ret)
- return ret;
- }
-
- /*
- * powerdown MIPI TX/RX PHY & disable MIPI
- *
- * MIPI CONTROL 00
- * 4: PWDN PHY TX
- * 3: PWDN PHY RX
- * 2: MIPI enable
- */
- ret = ov5640_write_reg(sensor,
- OV5640_REG_IO_MIPI_CTRL00, on ? 0x18 : 0);
- if (ret)
- return ret;
-
return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ?
OV5640_REG_SYS_CTRL0_SW_PWUP :
OV5640_REG_SYS_CTRL0_SW_PWDN);
@@ -2029,15 +1964,73 @@ static int ov5640_set_power_mipi(struct ov5640_dev *sensor, bool on)
static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on)
{
+ unsigned int flags = sensor->ep.bus.parallel.flags;
+ u8 pclk_pol = 0;
+ u8 hsync_pol = 0;
+ u8 vsync_pol = 0;
int ret;
if (!on) {
/* Reset settings to their default values. */
+ ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x58);
+ ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, 0x20);
ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, 0x00);
ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE02, 0x00);
return 0;
}
+ /*
+ * Note about parallel port configuration.
+ *
+ * When configured in parallel mode, the OV5640 will
+ * output 10 bits data on DVP data lines [9:0].
+ * If only 8 bits data are wanted, the 8 bits data lines
+ * of the camera interface must be physically connected
+ * on the DVP data lines [9:2].
+ *
+ * Control lines polarity can be configured through
+ * devicetree endpoint control lines properties.
+ * If no endpoint control lines properties are set,
+ * polarity will be as below:
+ * - VSYNC: active high
+ * - HREF: active low
+ * - PCLK: active low
+ */
+ /*
+ * configure parallel port control lines polarity
+ *
+ * POLARITY CTRL0
+ * - [5]: PCLK polarity (0: active low, 1: active high)
+ * - [1]: HREF polarity (0: active low, 1: active high)
+ * - [0]: VSYNC polarity (mismatch here between
+ * datasheet and hardware, 0 is active high
+ * and 1 is active low...)
+ */
+ if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
+ pclk_pol = 1;
+ if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
+ hsync_pol = 1;
+ if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
+ vsync_pol = 1;
+
+ ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00,
+ (pclk_pol << 5) | (hsync_pol << 1) | vsync_pol);
+
+ if (ret)
+ return ret;
+
+ /*
+ * powerdown MIPI TX/RX PHY & disable MIPI
+ *
+ * MIPI CONTROL 00
+ * 4: PWDN PHY TX
+ * 3: PWDN PHY RX
+ * 2: MIPI enable
+ */
+ ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x18);
+ if (ret)
+ return ret;
+
/*
* enable VSYNC/HREF/PCLK DVP control lines
* & D[9:6] DVP data lines
