This is a note to let you know that I've just added the patch titled
i2c: designware: Handle invalid SMBus block data response length value
to the 6.4-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
i2c-designware-handle-invalid-smbus-block-data-response-length-value.patch
and it can be found in the queue-6.4 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
>From 69f035c480d76f12bf061148ccfd578e1099e5fc Mon Sep 17 00:00:00 2001
From: Tam Nguyen <tamnguyenchi@xxxxxxxxxxxxxxxxxxxxxx>
Date: Wed, 26 Jul 2023 15:00:01 +0700
Subject: i2c: designware: Handle invalid SMBus block data response length value
From: Tam Nguyen <tamnguyenchi@xxxxxxxxxxxxxxxxxxxxxx>
commit 69f035c480d76f12bf061148ccfd578e1099e5fc upstream.
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Tam Nguyen <tamnguyenchi@xxxxxxxxxxxxxxxxxxxxxx>
Acked-by: Jarkko Nikula <jarkko.nikula@xxxxxxxxxxxxxxx>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@xxxxxxxxxxxxxxxxxxxxxx
Reviewed-by: Andi Shyti <andi.shyti@xxxxxxxxxx>
Signed-off-by: Wolfram Sang <wsa@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-designware-master.c | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -528,8 +528,19 @@ i2c_dw_read(struct dw_i2c_dev *dev)
regmap_read(dev->map, DW_IC_DATA_CMD, &tmp);
tmp &= DW_IC_DATA_CMD_DAT;
/* Ensure length byte is a valid value */
- if (flags & I2C_M_RECV_LEN &&
- tmp <= I2C_SMBUS_BLOCK_MAX && tmp > 0) {
+ if (flags & I2C_M_RECV_LEN) {
+ /*
+ * if IC_EMPTYFIFO_HOLD_MASTER_EN is set, which cannot be
+ * detected from the registers, the controller can be
+ * disabled if the STOP bit is set. But it is only set
+ * after receiving block data response length in
+ * I2C_FUNC_SMBUS_BLOCK_DATA case. That needs to read
+ * another byte with STOP bit set when the block data
+ * response length is invalid to complete the transaction.
+ */
+ if (!tmp || tmp > I2C_SMBUS_BLOCK_MAX)
+ tmp = 1;
+
len = i2c_dw_recv_len(dev, tmp);
}
*buf++ = tmp;
Patches currently in stable-queue which might be from tamnguyenchi@xxxxxxxxxxxxxxxxxxxxxx are
queue-6.4/i2c-designware-correct-length-byte-validation-logic.patch
queue-6.4/i2c-designware-handle-invalid-smbus-block-data-response-length-value.patch
