This is a note to let you know that I've just added the patch titled
can: mcp251xfd: __mcp251xfd_chip_set_mode(): increase poll timeout
to the 6.1-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
can-mcp251xfd-__mcp251xfd_chip_set_mode-increase-poll-timeout.patch
and it can be found in the queue-6.1 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
>From 9efa1a5407e81265ea502cab83be4de503decc49 Mon Sep 17 00:00:00 2001
From: Fedor Ross <fedor.ross@xxxxxxx>
Date: Thu, 4 May 2023 21:50:59 +0200
Subject: can: mcp251xfd: __mcp251xfd_chip_set_mode(): increase poll timeout
From: Fedor Ross <fedor.ross@xxxxxxx>
commit 9efa1a5407e81265ea502cab83be4de503decc49 upstream.
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f003e8 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Fedor Ross <fedor.ross@xxxxxxx>
Signed-off-by: Marek Vasut <marex@xxxxxxx>
Cc: stable@xxxxxxxxxxxxxxx
Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@xxxxxxxxxxxxxx
Signed-off-by: Marc Kleine-Budde <mkl@xxxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c | 10 ++++++++--
drivers/net/can/spi/mcp251xfd/mcp251xfd.h | 1 +
2 files changed, 9 insertions(+), 2 deletions(-)
--- a/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
+++ b/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
@@ -227,6 +227,8 @@ static int
__mcp251xfd_chip_set_mode(const struct mcp251xfd_priv *priv,
const u8 mode_req, bool nowait)
{
+ const struct can_bittiming *bt = &priv->can.bittiming;
+ unsigned long timeout_us = MCP251XFD_POLL_TIMEOUT_US;
u32 con = 0, con_reqop, osc = 0;
u8 mode;
int err;
@@ -246,12 +248,16 @@ __mcp251xfd_chip_set_mode(const struct m
if (mode_req == MCP251XFD_REG_CON_MODE_SLEEP || nowait)
return 0;
+ if (bt->bitrate)
+ timeout_us = max_t(unsigned long, timeout_us,
+ MCP251XFD_FRAME_LEN_MAX_BITS * USEC_PER_SEC /
+ bt->bitrate);
+
err = regmap_read_poll_timeout(priv->map_reg, MCP251XFD_REG_CON, con,
!mcp251xfd_reg_invalid(con) &&
FIELD_GET(MCP251XFD_REG_CON_OPMOD_MASK,
con) == mode_req,
- MCP251XFD_POLL_SLEEP_US,
- MCP251XFD_POLL_TIMEOUT_US);
+ MCP251XFD_POLL_SLEEP_US, timeout_us);
if (err != -ETIMEDOUT && err != -EBADMSG)
return err;
--- a/drivers/net/can/spi/mcp251xfd/mcp251xfd.h
+++ b/drivers/net/can/spi/mcp251xfd/mcp251xfd.h
@@ -387,6 +387,7 @@ static_assert(MCP251XFD_TIMESTAMP_WORK_D
#define MCP251XFD_OSC_STAB_TIMEOUT_US (10 * MCP251XFD_OSC_STAB_SLEEP_US)
#define MCP251XFD_POLL_SLEEP_US (10)
#define MCP251XFD_POLL_TIMEOUT_US (USEC_PER_MSEC)
+#define MCP251XFD_FRAME_LEN_MAX_BITS (736)
/* Misc */
#define MCP251XFD_NAPI_WEIGHT 32
Patches currently in stable-queue which might be from fedor.ross@xxxxxxx are
queue-6.1/can-mcp251xfd-__mcp251xfd_chip_set_mode-increase-poll-timeout.patch
