This is a note to let you know that I've just added the patch titled
net: phy: dp83td510: fix kernel stall during netboot in DP83TD510E PHY driver
to the 6.1-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
net-phy-dp83td510-fix-kernel-stall-during-netboot-in-dp83td510e-phy-driver.patch
and it can be found in the queue-6.1 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.
>From fc0649395dca81f2b3b02d9b248acb38cbcee55c Mon Sep 17 00:00:00 2001
From: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
Date: Wed, 21 Jun 2023 06:38:48 +0200
Subject: net: phy: dp83td510: fix kernel stall during netboot in DP83TD510E PHY driver
From: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
commit fc0649395dca81f2b3b02d9b248acb38cbcee55c upstream.
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.
This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.
The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.
Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.
Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@xxxxxxxxxxxxxx
Signed-off-by: Jakub Kicinski <kuba@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/net/phy/dp83td510.c | 23 +++++------------------
1 file changed, 5 insertions(+), 18 deletions(-)
--- a/drivers/net/phy/dp83td510.c
+++ b/drivers/net/phy/dp83td510.c
@@ -12,6 +12,11 @@
/* MDIO_MMD_VEND2 registers */
#define DP83TD510E_PHY_STS 0x10
+/* Bit 7 - mii_interrupt, active high. Clears on read.
+ * Note: Clearing does not necessarily deactivate IRQ pin if interrupts pending.
+ * This differs from the DP83TD510E datasheet (2020) which states this bit
+ * clears on write 0.
+ */
#define DP83TD510E_STS_MII_INT BIT(7)
#define DP83TD510E_LINK_STATUS BIT(0)
@@ -53,12 +58,6 @@ static int dp83td510_config_intr(struct
int ret;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
- /* Clear any pending interrupts */
- ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS,
- 0x0);
- if (ret)
- return ret;
-
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
DP83TD510E_INTERRUPT_REG_1,
DP83TD510E_INT1_LINK_EN);
@@ -81,10 +80,6 @@ static int dp83td510_config_intr(struct
DP83TD510E_GENCFG_INT_EN);
if (ret)
return ret;
-
- /* Clear any pending interrupts */
- ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS,
- 0x0);
}
return ret;
@@ -94,14 +89,6 @@ static irqreturn_t dp83td510_handle_inte
{
int ret;
- ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS);
- if (ret < 0) {
- phy_error(phydev);
- return IRQ_NONE;
- } else if (!(ret & DP83TD510E_STS_MII_INT)) {
- return IRQ_NONE;
- }
-
/* Read the current enabled interrupts */
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_INTERRUPT_REG_1);
if (ret < 0) {
Patches currently in stable-queue which might be from o.rempel@xxxxxxxxxxxxxx are
queue-6.1/net-phy-dp83td510-fix-kernel-stall-during-netboot-in-dp83td510e-phy-driver.patch
