This is a note to let you know that I've just added the patch titled serial: 8250_mtk: Fix UART_EFR register address to the 5.17-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary The filename of the patch is: serial-8250_mtk-fix-uart_efr-register-address.patch and it can be found in the queue-5.17 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable@xxxxxxxxxxxxxxx> know about it. >From bb0b197aadd928f52ce6f01f0ee977f0a08cf1be Mon Sep 17 00:00:00 2001 From: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx> Date: Wed, 27 Apr 2022 15:23:26 +0200 Subject: serial: 8250_mtk: Fix UART_EFR register address From: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx> commit bb0b197aadd928f52ce6f01f0ee977f0a08cf1be upstream. On MediaTek SoCs, the UART IP is 16550A compatible, but there are some specific quirks: we are declaring a register shift of 2, but this is only valid for the majority of the registers, as there are some that are out of the standard layout. Specifically, this driver is using definitions from serial_reg.h, where we have a UART_EFR register defined as 2: this results in a 0x8 offset, but there we have the FCR register instead. The right offset for the EFR register on MediaTek UART is at 0x98, so, following the decimal definition convention in serial_reg.h and accounting for the register left shift of two, add and use the correct register address for this IP, defined as decimal 38, so that the final calculation results in (0x26 << 2) = 0x98. Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx> Cc: stable <stable@xxxxxxxxxxxxxxx> Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@xxxxxxxxxxxxx Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/tty/serial/8250/8250_mtk.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -37,6 +37,7 @@ #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */ +#define MTK_UART_EFR 38 /* I/O: Extended Features Register */ #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ @@ -169,7 +170,7 @@ static void mtk8250_dma_enable(struct ua MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr); if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0) @@ -232,7 +233,7 @@ static void mtk8250_set_flow_ctrl(struct int lcr = serial_in(up, UART_LCR); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr); lcr = serial_in(up, UART_LCR); @@ -241,7 +242,7 @@ static void mtk8250_set_flow_ctrl(struct serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); serial_out(up, MTK_UART_ESCAPE_EN, 0x00); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); serial_out(up, UART_LCR, lcr); mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | @@ -255,8 +256,8 @@ static void mtk8250_set_flow_ctrl(struct serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /*enable hw flow control*/ - serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); serial_out(up, UART_LCR, lcr); @@ -270,8 +271,8 @@ static void mtk8250_set_flow_ctrl(struct serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /*enable sw flow control */ - serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); serial_out(up, UART_XON1, START_CHAR(port->state->port.tty)); Patches currently in stable-queue which might be from angelogioacchino.delregno@xxxxxxxxxxxxx are queue-5.17/serial-8250_mtk-make-sure-to-select-the-right-feature_sel.patch queue-5.17/serial-8250_mtk-fix-register-address-for-xon-xoff-character.patch queue-5.17/serial-8250_mtk-fix-uart_efr-register-address.patch