From: Robert Hancock <robert.hancock@xxxxxxxxxx> commit 0bf476fc3624e3a72af4ba7340d430a91c18cd67 upstream. There is an oddity in the way the RSR register flags propagate to the ISR register (and the actual interrupt output) on this hardware: it appears that RSR register bits only result in ISR being asserted if the interrupt was actually enabled at the time, so enabling interrupts with RSR bits already set doesn't trigger an interrupt to be raised. There was already a partial fix for this race in the macb_poll function where it checked for RSR bits being set and re-triggered NAPI receive. However, there was a still a race window between checking RSR and actually enabling interrupts, where a lost wakeup could happen. It's necessary to check again after enabling interrupts to see if RSR was set just prior to the interrupt being enabled, and re-trigger receive in that case. This issue was noticed in a point-to-point UDP request-response protocol which periodically saw timeouts or abnormally high response times due to received packets not being processed in a timely fashion. In many applications, more packets arriving, including TCP retransmissions, would cause the original packet to be processed, thus masking the issue. Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done") Cc: stable@xxxxxxxxxxxxxxx Co-developed-by: Scott McNutt <scott.mcnutt@xxxxxxxxxxxx> Signed-off-by: Scott McNutt <scott.mcnutt@xxxxxxxxxxxx> Signed-off-by: Robert Hancock <robert.hancock@xxxxxxxxxx> Tested-by: Claudiu Beznea <claudiu.beznea@xxxxxxxxxxxxx> Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/net/ethernet/cadence/macb_main.c | 25 ++++++++++++++++++++++++- 1 file changed, 24 insertions(+), 1 deletion(-) --- a/drivers/net/ethernet/cadence/macb_main.c +++ b/drivers/net/ethernet/cadence/macb_main.c @@ -1269,7 +1269,14 @@ static int macb_poll(struct napi_struct if (work_done < budget) { napi_complete_done(napi, work_done); - /* Packets received while interrupts were disabled */ + /* RSR bits only seem to propagate to raise interrupts when + * interrupts are enabled at the time, so if bits are already + * set due to packets received while interrupts were disabled, + * they will not cause another interrupt to be generated when + * interrupts are re-enabled. + * Check for this case here. This has been seen to happen + * around 30% of the time under heavy network load. + */ status = macb_readl(bp, RSR); if (status) { if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE) @@ -1277,6 +1284,22 @@ static int macb_poll(struct napi_struct napi_reschedule(napi); } else { queue_writel(queue, IER, bp->rx_intr_mask); + + /* In rare cases, packets could have been received in + * the window between the check above and re-enabling + * interrupts. Therefore, a double-check is required + * to avoid losing a wakeup. This can potentially race + * with the interrupt handler doing the same actions + * if an interrupt is raised just after enabling them, + * but this should be harmless. + */ + status = macb_readl(bp, RSR); + if (unlikely(status)) { + queue_writel(queue, IDR, bp->rx_intr_mask); + if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE) + queue_writel(queue, ISR, MACB_BIT(RCOMP)); + napi_schedule(napi); + } } } Patches currently in stable-queue which might be from robert.hancock@xxxxxxxxxx are queue-4.19/net-macb-fix-lost-rx-packet-wakeup-race-in-napi-receive.patch