Patch "ARM: dts: stm32: Swap PHY reset GPIO and TSC2004 IRQ on DHCOM SOM" has been added to the 5.9-stable tree

[Sasha Levin <sashal@xxxxxxxxxx>]

This is a note to let you know that I've just added the patch titled

    ARM: dts: stm32: Swap PHY reset GPIO and TSC2004 IRQ on DHCOM SOM

to the 5.9-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     arm-dts-stm32-swap-phy-reset-gpio-and-tsc2004-irq-on.patch
and it can be found in the queue-5.9 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@xxxxxxxxxxxxxxx> know about it.



commit 0903ced998b01ed7ba9fc88f48fe1b0db490d974
Author: Marek Vasut <marex@xxxxxxx>
Date:   Fri Aug 28 14:14:12 2020 +0200

    ARM: dts: stm32: Swap PHY reset GPIO and TSC2004 IRQ on DHCOM SOM
    
    [ Upstream commit 9ad98319e95263469d8ca2cb543c37c5a2f40980 ]
    
    On the production revision of the SoM, 587-200, the PHY reset GPIO and
    touchscreen IRQs are swapped to prevent collision between EXTi IRQs,
    reflect that in DT.
    
    Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
    Signed-off-by: Marek Vasut <marex@xxxxxxx>
    Cc: Alexandre Torgue <alexandre.torgue@xxxxxx>
    Cc: Maxime Coquelin <mcoquelin.stm32@xxxxxxxxx>
    Cc: Patrice Chotard <patrice.chotard@xxxxxx>
    Cc: Patrick Delaunay <patrick.delaunay@xxxxxx>
    Cc: linux-stm32@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
    To: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
    Signed-off-by: Alexandre Torgue <alexandre.torgue@xxxxxx>
    Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index d30a3c60da9b0..a87ebc4843963 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -117,7 +117,7 @@ &ethernet0 {
 	max-speed = <100>;
 	phy-handle = <&phy0>;
 	st,eth-ref-clk-sel;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+	phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
 
 	mdio0 {
 		#address-cells = <1>;
@@ -285,7 +285,7 @@ touchscreen@49 {
 		compatible = "ti,tsc2004";
 		reg = <0x49>;
 		vio-supply = <&v3v3>;
-		interrupts-extended = <&gpioh 3 IRQ_TYPE_EDGE_FALLING>;
+		interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
 	};
 
 	eeprom@50 {