Hey, CentOS 9 is mainly uses nftables when possible. I have not seen any example of squid intercept examples with nftables. If for any reason the iptables command would not work on CentOS 9 (stream) let me know and I might be able to provide these. Eliezer ---- Eliezer Croitoru NgTech, Tech Support Mobile: +972-5-28704261 Email: ngtech1ltd@xxxxxxxxx Web: https://ngtech.co.il/ My-Tube: https://tube.ngtech.co.il/ -----Original Message----- From: squid-users <squid-users-bounces@xxxxxxxxxxxxxxxxxxxxx> On Behalf Of Amos Jeffries Sent: Thursday, 17 November 2022 6:35 To: squid-users@xxxxxxxxxxxxxxxxxxxxx Subject: Re: transparent mode squid on centos 9 with iptables (part 2) On 17/11/2022 9:14 am, Lola Lo wrote: > Hi guys. > > > Could you please send a tutorial or any good guidance to implement > squid on transparent mode on centos 9 with iptables. > The configuration details for what you appear to be trying to configure are here: <https://wiki.squid-cache.org/ConfigExamples/Intercept/LinuxRedirect> My comments below relate to how your attempt differs and how to fix. > I have configured squid.conf with this parameters: > > > > ens192: 172.31.168.28, internet interface > > ens224: 192.168.1.10, LAN interface (private network) > > > # Mis ACLs # > > acl mi_red src 192.168.1.0/24 <http://192.168.1.0/24> > > acl cliente_linux src 192.168.1.20 > > acl cliente_windows src 192.168.1.30 > > acl sitios1 url_regex "/etc/squid/listas/sitios1" > > acl sitios2 url_regex "/etc/squid/listas/sitios2" > > > # Squid normally listens to port 3128 > > http_port 3128 > > http_port 8080 transparent > > Firstly, use "intercept" instead of "transparent" with modern Squid. Secondly, remember that only port 8080 is setup to receive intercepted traffic. Port 3128 still receives normal forward-proxy traffic. > I want the “deny all” rule get applied to test the client using the proxy > > You have not shown any http_access lines from your config. There is a clear bug in your NAT which explains the behaviour so I will assume that the squid.conf policy does what you want. > My iptables is configured as follows: > > > #!/bin/bash > > > ## NAT server configuration ## > > > sysctl -w net.ipv4.ip_forward=1 > > sysctl -p > > iptables -X > > iptables -F > > iptables -t nat -X > > iptables -t nat -F > > iptables -I INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT > > iptables -I FORWARD-m state --state RELATED,ESTABLISHED -j ACCEPT > > iptables -t nat -I POSTROUTING -o ens192 -j MASQUERADE > > > Why is this a different script? Ideally the firewall rules should be as atomic as possible to avoid connections being setup with only part of the rules applied. > > #!/bin/bash > > > ## proxy server configuration ## > > > ### Accepting traffic for the ports: 3128 and 8080## > > > iptables -A INPUT -s 192.168.1.0/24 <http://192.168.1.0/24> -p tcp > --dport 3128 -j ACCEPT > > iptables -A INPUT -p tcp --dport 3128 -j DROP > Do not accept traffic directly to the port 8080. Also Squid does not make outbound connections from its listening ports. So these ... > iptables -A OUTPUT -d 192.168.1.0/24 <http://192.168.1.0/24> -p tcp > --sport 3128 -j ACCEPT > > iptables -A OUTPUT -p tcp --sport 3128 -j DROP > > > iptables -A INPUT -s 192.168.1.0/24 <http://192.168.1.0/24> -p tcp > --dport 8080 -j ACCEPT > > iptables -A INPUT -p tcp --dport 8080 -j DROP > > iptables -A OUTPUT -d 192.168.1.0/24 <http://192.168.1.0/24> -p tcp > --sport 8080 -j ACCEPT > > iptables -A OUTPUT -p tcp --sport 8080 -j DROP > > ... should be replaced with: iptables -t mangle -A PREROUTING -p tcp --dport 8080 -j DROP > > `### Accepting traffic for the ports: 3128 and 8080## > > > iptables -t nat -A POSTROUTING -o ens192 -j MASQUERADE > You are missing a rule to allow Squid outbound traffic to avoid the NAT. iptables -t nat -A PREROUTING -s 192.168.1.10 -p tcp --dport 80 -j ACCEPT > iptables -t nat -A PREROUTING -s 192.168.1.0/24 > <http://192.168.1.0/24> -p tcp --dport 80 -j REDIRECT --to-port 8080 > > iptables -t nat -A PREROUTING -s 192.168.1.0/24 > <http://192.168.1.0/24> -p tcp --dport 443 -j REDIRECT --to-port 8080 > > Port 8080 in your squid.conf can only handle port 80 traffic syntax. Port 443 is a more tricky situation. I recommend removing that until you have the port 80 working. > > But I got this error: > > > 1668381894.7460 192.168.1.20 NONE_NONE/000 0 - > error:transaction-end-before-headers - HIER_NONE/- - > > 1668381967.8000 192.168.1.20 NONE_NONE/400 3690 - > error:invalid-request - HIER_NONE/- text/html > This is likely from the missing NAT rule allowing Squid outbound. If the above changes do not fix everything make sure that you test exactly what the real clients will be doing. Specifically that they are making contact to servers on port 80 or directly to Squid port 3128. They know *nothing* about port 8080 existence so have no reason to send anything that way directly. HTH Amos _______________________________________________ squid-users mailing list squid-users@xxxxxxxxxxxxxxxxxxxxx http://lists.squid-cache.org/listinfo/squid-users _______________________________________________ squid-users mailing list squid-users@xxxxxxxxxxxxxxxxxxxxx http://lists.squid-cache.org/listinfo/squid-users
