Re: Assistance with WCCPv2 Setup with Cisco Router

[Yuri Voinov <yvoinov@xxxxxxxxx>]

Ah, forgot about this:

http://wiki.squid-cache.org/ConfigExamples/Intercept

22.03.2017 1:04, Waldon, Cooper пишет:

Hello All,

 

I’m trying to set up a transparent proxy for http and https using Cisco Routers and Squid.  I have followed the configuration examples that are listed under the wccp2 overview section (http://wiki.squid-cache.org/Features/Wccp2) of the squid wiki but I’m still having some issues.

 

I have a little lab set up with a Cisco 7200 Router and a VM with CentOS running the proxy.

 

The “WAN” IP of the Router is 192.168.0.23.  The IP of the Squid Proxy is 192.168.0.24 and both have the default gateway of 192.168.0.1 which is the “ISP”

 

The Client is sitting on a LAN behind the Router in the 10.10.10.0/24 subnet and is also sitting behind nat.

 

I believe that the router and proxy are communicating properly based on the information in the show ip wccp command on the router as it shows clients and routers as well as showing that packets are being forwarded:

 

R3#show ip wccp

Global WCCP information:

    Router information:

        Router Identifier:                   192.168.0.23

        Configured source-interface:         GigabitEthernet5/0

 

    Service Identifier: web-cache

        Protocol Version:                    2.00

        Number of Service Group Clients:     1

        Number of Service Group Routers:     1

        Total Packets Redirected:            1079

          Process:                           0

          CEF:                               1079

        Service mode:                        Open

        Service Access-list:                 -none-

        Total Packets Dropped Closed:        0

        Redirect access-list:                100

        Total Packets Denied Redirect:       0

        Total Packets Unassigned:            0

        Group access-list:                   10

        Total Messages Denied to Group:      0

        Total Authentication failures:       0

        Total GRE Bypassed Packets Received: 0

          Process:                           0

          CEF:                               0

       GRE tunnel interface:                Tunnel1

 

    Service Identifier: 70

        Protocol Version:                    2.00

        Number of Service Group Clients:     1

        Number of Service Group Routers:     1

        Total Packets Redirected:            500

          Process:                           0

          CEF:                               500

        Service mode:                        Open

        Service Access-list:                 -none-

        Total Packets Dropped Closed:        0

        Redirect access-list:                100

        Total Packets Denied Redirect:       0

        Total Packets Unassigned:            0

        Group access-list:                   10

        Total Messages Denied to Group:      0

        Total Authentication failures:       0

        Total GRE Bypassed Packets Received: 0

          Process:                           0

          CEF:                               0

        GRE tunnel interface:                Tunnel0

 

Here is the relevant squid wccp configuration:

 

----Output removed----

# Squid normally listens to port 3128

http_port 3128

http_port 0.0.0.0:3129

 

# WCCPv2 Parameters

wccp2_router 192.168.0.23

wccp2_forwarding_method 1

wccp2_return_method 1

wccp2_assignment_method hash

wccp2_service standard 0

wccp2_service dynamic 70

wccp2_service_info 70 protocol=tcp flags=dst_ip_hash,src_ip_alt_hash,src_port_alt_hash priority=231 ports=443

 

---Output remove----

 

I think that the issue lies with the iptables configuration as I do not see any packets been processed in the nat table.  I have tried a few different methods such as:

 

iptables -t nat -A PREROUTING -i wccp0 -p tcp –dport 80 -j REDIRECT –to-port 3129

iptables -t nat -A PREROUTING -i wccp0 -p tcp –dport 443 -j REDIRECT –to-port 3129

iptables -t nat -A POSTROUTING -j MASQUERADE

 

or

 

iptables -t nat -A PREROUTING -p tcp –dport 80 -j DNAT –to-destination 192.168.0.24:3129

iptables -t nat -A PREROUTING -p tcp –dport 443 -j DNAT –to-destination 192.168.0.24:3129

iptables -t nat -A POSTROUTING -j MASQUERADE

 

I have also tried adding ACCEPT commands to the PREROUTING zone just in case the proxy is dropping the packets right away but that also doesn’t work.

 

The proxy functions perfectly when the client is configured to use a proxy so there doesn’t appear to be any issues with routing or anything like that, it’s just the transparent proxying that isn’t working.

 

If anyone has any suggestions of what I could try that would be greatly appreciated.  Let me know if anything is unclear or if you need further clarification.

 

Thank you,

Cooper Waldon

 

 

Cooper Waldon l Network Engineer l OTN l 416-446-4110 x 4473 l www.otn.ca | Service Desk 1-855-654-0888 x2

 

_______________________________________________
squid-users mailing list
squid-users@xxxxxxxxxxxxxxxxxxxxx
http://lists.squid-cache.org/listinfo/squid-users

--
Bugs to the Future

Attachment: 0x613DEC46.asc
Description: application/pgp-keys

Attachment: signature.asc
Description: OpenPGP digital signature

_______________________________________________
squid-users mailing list
squid-users@xxxxxxxxxxxxxxxxxxxxx
http://lists.squid-cache.org/listinfo/squid-users