On 11/22/2012 12:14 PM, Leslie Jensen wrote:
<<SNIP>>
At the moment I've reverted back to 3.1 but I would like to make a
successful upgrade :-)
Thanks
/Leslie
It seems to me like there is a problem in your NAT settings in PF.
but I didnt tested it.
I have been using this:
##start
ext_if=em0
int_if=em1
rede="{192.168.11.0/24}"
nat on $ext_if from $rede to any -> ($ext_if)
#rdr on $ext_if inet proto tcp to port 22 -> 192.168.1.102 22
#set skip on $int_if << These lines commented out
#set skip on $wi_if
# redirect only IPv4 web traffic to squid
rdr pass inet proto tcp from 192.168.11.0/24 to any port 80 -> 127.0.0.1
port 3129
#block in
pass in quick on $int_if
pass in quick on $ext_if
pass out keep state
##end
with: squid.conf
#
# Recommended minimum configuration:
#
# Example rule allowing access from your local networks.
# Adapt to list your (internal) IP networks from where browsing
# should be allowed
acl localnet src 10.0.0.0/8 # RFC1918 possible internal network
acl localnet src 172.16.0.0/12 # RFC1918 possible internal network
acl localnet src 192.168.0.0/16 # RFC1918 possible internal network
acl localnet src fc00::/7 # RFC 4193 local private network range
acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged)
machines
acl SSL_ports port 443
acl Safe_ports port 80 # http
acl Safe_ports port 21 # ftp
acl Safe_ports port 443 # https
acl Safe_ports port 70 # gopher
acl Safe_ports port 210 # wais
acl Safe_ports port 1025-65535 # unregistered ports
acl Safe_ports port 280 # http-mgmt
acl Safe_ports port 488 # gss-http
acl Safe_ports port 591 # filemaker
acl Safe_ports port 777 # multiling http
acl CONNECT method CONNECT
#
# Recommended minimum Access Permission configuration:
#
# Only allow cachemgr access from localhost
http_access allow localhost manager
http_access deny manager
# Deny requests to certain unsafe ports
http_access deny !Safe_ports
# Deny CONNECT to other than secure SSL ports
http_access deny CONNECT !SSL_ports
# We strongly recommend the following be uncommented to protect innocent
# web applications running on the proxy server who think the only
# one who can access services on "localhost" is a local user
#http_access deny to_localhost
#
# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS
#
# Example rule allowing access from your local networks.
# Adapt localnet in the ACL section to list your (internal) IP networks
# from where browsing should be allowed
http_access allow localnet
http_access allow localhost
# And finally deny all other access to this proxy
http_access deny all
# Squid normally listens to port 3128
http_port 3128
http_port 3129 intercept
# Uncomment and adjust the following to add a disk cache directory.
#cache_dir ufs /usr/local/squid/var/cache/squid 100 16 256
# Leave coredumps in the first cache dir
coredump_dir /usr/local/squid/var/cache/squid
# Add any of your own refresh_pattern entries above these.
refresh_pattern ^ftp: 1440 20% 10080
refresh_pattern ^gopher: 1440 0% 1440
refresh_pattern -i (/cgi-bin/|\?) 0 0% 0
refresh_pattern . 0 20% 4320
cache_effective_user squid
##end
and it seems to work fine.
I compiled squid with basic
./configure --enable-pf-transparent
nothing more.
Regards,
Eliezer
--
Eliezer Croitoru
https://www1.ngtech.co.il
sip:ngtech@xxxxxxxxxxxx
IT consulting for Nonprofit organizations
eliezer <at> ngtech.co.il
