> Thanks, this is really interesting. Would you mind replacing the test
> patch with the following (this applies directly on the upstream
> kernel, e.g., fd3b36d27566)?
>
> Sorry for the back and forth, but there's a lot going on here that I
> don't understand.
>
> I'd like to see the complete dmesg log, /proc/iomem, and "lspci -vv".
00000000-7effdfff : System RAM
00404000-0085ab9f : Kernel code
0085aba0-009b8a8f : Kernel data
009f2000-00a37a37 : Kernel bss
7f000000-7fee5fff : System RAM
7ff04000-7ff0bfff : System RAM
1ff00000000-1ffffffffff : /pci@1f,0
1ff00000000-1ff000fffff : 0000:00:07.0
1ff00400000-1ff0041ffff : 0000:00:0c.1
1ff00400000-1ff0041ffff : sungem
1ff00420000-1ff00421fff : 0000:00:0c.2
1ff00422000-1ff00423fff : 0000:00:0c.2
1ff00424000-1ff00425fff : 0000:00:08.0
1ff00426000-1ff00427fff : 0000:00:13.0
1ff00440000-1ff0045ffff : 0000:00:13.0
1ff00800000-1ff00bfffff : 0000:00:0c.1
1ff00c00000-1ff00ffffff : 0000:00:0c.2
1ff01000000-1ff013fffff : 0000:00:0c.3
1ff02000000-1ff02ffffff : 0000:00:0c.3
1ff02000000-1ff02ffffff : ohci_hcd
1ff03000000-1ff030fffff : PCI Bus 0000:01
1ff03000000-1ff03001fff : 0000:01:00.0
1ff03000000-1ff03001fff : sym53c8xx
1ff03002000-1ff03003fff : 0000:01:02.0
1ff03010000-1ff0301ffff : 0000:01:02.0
1ff04000000-1ff04ffffff : 0000:00:13.0
1ff04000000-1ff04ffffff : atyfb
1ffc0000000-1ffdfffffff : IOMMU
1fff1000000-1fff1001fff : eeprom
00:03.0 Non-VGA unclassified device: ULi Electronics Inc. M7101 Power Management Controller [PMU]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: [virtual] I/O ports at <unassigned> [size=16]
Kernel driver in use: ali1535_smbus
00: b9 10 01 71 00 00 00 02 00 00 00 00 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 20 00 08 18 08 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40 01
70: 0f 11 00 00 00 00 00 08 00 00 00 00 00 00 00 00
80: 00 00 10 10 00 00 00 00 01 04 00 00 00 00 00 00
90: 00 00 02 00 00 00 00 0f 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 40 40 01 00 00 02 00 60 04 01 03 00 00 00 30
c0: 00 10 ff 00 00 00 00 00 01 00 00 00 00 00 00 00
d0: ff 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 08 00 06 01 00 01 00 00 00 00 00 00 00 00 00
f0: 45 00 20 7e 00 00 00 00 00 00 00 00 00 00 00 00
00:05.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 03000000-030fffff
Prefetchable memory behind bridge: fffffffffff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
00: 11 10 24 00 07 00 90 02 03 00 04 06 10 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 11 11 80 02
20: 00 03 00 03 f1 ff 01 00 ff ff ff ff 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 3e 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 01 01
e0: 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 ISA bridge: ULi Electronics Inc. M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+]
Subsystem: ULi Electronics Inc. ALi M1533 Aladdin IV/V ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] I/O ports at 1fe02000000 [size=64K]
Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [size=1M]
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: b9 10 33 15 0f 00 10 02 00 00 01 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 b9 10 33 15
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40: 11 13 49 80 83 09 00 07 00 00 00 10 00 00 fd 01
50: 00 00 00 40 00 07 02 00 6e 03 09 00 00 00 00 08
60: 00 00 00 00 00 00 00 00 00 00 00 00 80 20 00 00
70: 00 00 06 00 41 03 00 d3 04 02 00 02 00 00 01 10
80: 07 00 33 01 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 Multimedia audio controller: ULi Electronics Inc. M5451 PCI AC-Link Controller Audio Device (rev 01)
Subsystem: ULi Electronics Inc. M5451 PCI AC-Link Controller Audio Device
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 0900 [disabled] [size=256]
Region 1: Memory at 00424000 (32-bit, non-prefetchable) [disabled] [size=8K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: b9 10 51 54 00 00 90 02 01 00 01 04 00 40 00 00
10: 01 09 00 00 00 40 42 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 b9 10 51 54
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 01 02 18
40: 00 00 00 00 00 04 00 e2 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 22 e6
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.0 Bridge: Oracle/SUN RIO EBUS (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 6250ns max), Cache Line Size: 64 bytes
BIST result: 00
Region 0: Memory at <ignored> (32-bit, non-prefetchable)
Region 1: Memory at <ignored> (32-bit, non-prefetchable)
00: 8e 10 00 11 46 01 80 02 01 00 80 06 10 40 80 80
10: 00 00 00 f0 00 00 00 f1 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 19
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.1 Ethernet controller: Oracle/SUN RIO 10/100 Ethernet [eri] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 1250ns max), Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 11
BIST result: 00
Region 0: Memory at 00400000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 00800000 [disabled] [size=4M]
Kernel driver in use: gem
00: 8e 10 01 11 06 00 80 02 01 00 00 02 10 40 80 80
10: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 0a 05
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.2 FireWire (IEEE 1394): Oracle/SUN RIO 1394 (rev 01) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 12
BIST result: 00
Region 0: Memory at 00420000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at 00422000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at 00c00000 [disabled] [size=4M]
00: 8e 10 02 11 02 00 80 02 01 10 00 0c 10 40 80 80
10: 00 00 42 00 00 20 42 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 0a 05
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.3 USB controller: Oracle/SUN RIO USB (rev 01) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 1250ns max), Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 13
BIST result: 00
Region 0: Memory at 02000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at 01000000 [disabled] [size=4M]
Kernel driver in use: ohci-pci
00: 8e 10 03 11 06 00 80 02 01 10 03 0c 10 40 80 80
10: 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 0a 05
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0d.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c3) (prog-if ff)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 0a00 [size=8]
Region 1: I/O ports at 0a18 [size=8]
Region 2: I/O ports at 0a10 [size=8]
Region 3: I/O ports at 0a08 [size=8]
Region 4: I/O ports at 0a20 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_ali
00: b9 10 29 52 05 00 90 02 c3 ff 01 01 00 40 00 00
10: 01 0a 00 00 19 0a 00 00 11 0a 00 00 09 0a 00 00
20: 21 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 00 01 02 04
40: 06 00 00 7f 00 00 00 00 00 02 20 c9 00 80 ba 1a
50: 03 00 00 81 08 00 a8 00 01 31 31 31 03 09 0a 0a
60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 21 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Rage XL PCI (rev 27) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at 04000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 0b00 [size=256]
Region 2: Memory at 00426000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at 00440000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: atyfb
00: 02 10 52 47 83 00 90 02 27 00 00 03 10 40 00 00
10: 00 00 00 04 01 0b 00 00 00 60 42 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 44 00 5c 00 00 00 00 00 00 00 f1 01 08 00
40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 5c 10 00 01 00 00 ff 00 00 00 00 01 00 02 06
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.0 SCSI storage controller: LSI Logic / Symbios Logic 53c810 (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 03000000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: sym53c8xx
00: 00 10 01 00 17 00 00 02 12 00 00 01 10 40 00 00
10: 01 10 00 00 00 00 00 03 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 08 40
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: da 00 00 03 47 00 06 1f 00 08 00 00 80 00 00 02
90: ff e0 dc c1 00 ff ff ff 00 f0 31 21 a0 13 dd c1
a0: 00 08 00 01 00 00 00 50 c0 13 dd c1 c0 13 dd c1
b0: 00 10 dd c1 38 f0 dc c1 ce 6d 00 a1 c0 23 ba c1
c0: 8f 05 00 00 00 05 40 0f 0c 00 80 0f 07 00 02 80
d0: 00 00 02 80 00 00 02 80 00 00 02 80 00 01 ff 40
e0: 00 01 ff 40 00 01 ff 40 00 01 ff 40 00 01 ff 40
f0: 00 01 ff 40 00 01 ff 40 00 01 ff 40 00 01 ff 40
01:01.0 Multimedia audio controller: C-Media Electronics Inc CMI8738/CMI8768 PCI Audio (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 1100 [disabled] [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: f6 13 11 01 00 00 10 02 10 00 01 04 00 40 00 00
10: 01 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 01
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 01 02 18
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 06 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:02.0 Multimedia audio controller: Cirrus Logic Crystal CS4281 PCI Audio (rev 01)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 03002000 (32-bit, non-prefetchable) [disabled] [size=8K]
Region 1: Memory at 03010000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 13 10 05 60 00 00 10 02 01 00 01 04 00 40 00 00
10: 00 20 00 03 00 00 01 03 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 01 04 18
40: 01 00 22 7e 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00
f0: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 0.000059] PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:31'
[ 0.000116] PROMLIB: Root node compatible:
[ 0.000217] Linux version 4.16.0-11316-gf77cfbe-dirty (mroos@blade100) (gcc version 4.9.3 (Debian 4.9.3-2)) #168 Wed Apr 11 23:14:41 EEST 2018
[ 0.280335] bootconsole [earlyprom0] enabled
[ 0.331447] ARCH: SUN4U
[ 0.360724] Ethernet address: 00:03:ba:0b:7d:5d
[ 0.414898] MM: PAGE_OFFSET is 0xfffff80000000000 (max_phys_bits == 40)
[ 0.494057] MM: VMALLOC [0x0000000100000000 --> 0x0000060000000000]
[ 0.568973] MM: VMEMMAP [0x0000060000000000 --> 0x00000c0000000000]
[ 0.720460] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.797625] Remapping the kernel...
[ 0.798175] done.
[ 1.201703] OF stdout device is: /pci@1f,0/isa@7/serial@0,3f8
[ 1.270449] PROM: Built device tree with 90708 bytes of memory.
[ 1.341590] Top of RAM: 0x7ff0c000, Total RAM: 0x7feec000
[ 1.406150] Memory hole size: 0MB
[ 1.979239] Allocated 16384 bytes for kernel page tables.
[ 2.044448] Zone ranges:
[ 2.074793] Normal [mem 0x0000000000000000-0x000000007ff0bfff]
[ 2.148765] Movable zone start for each node
[ 2.199783] Early memory node ranges
[ 2.242493] node 0: [mem 0x0000000000000000-0x000000007effdfff]
[ 2.317409] node 0: [mem 0x000000007f000000-0x000000007fee5fff]
[ 2.392326] node 0: [mem 0x000000007ff04000-0x000000007ff0bfff]
[ 2.467248] Initmem setup node 0 [mem 0x0000000000000000-0x000000007ff0bfff]
[ 2.551514] On node 0 totalpages: 262006
[ 2.551525] Normal zone: 2048 pages used for memmap
[ 2.551530] Normal zone: 0 pages reserved
[ 2.551539] Normal zone: 262006 pages, LIFO batch:15
[ 2.653830] Booting Linux...
[ 2.688370] CPU CAPS: [flush,stbar,swap,muldiv,v9,mul32,div32,v8plus]
[ 2.765450] CPU CAPS: [vis]
[ 2.804900] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 2.804913] pcpu-alloc: [0] 0
[ 2.807648] Built 1 zonelists, mobility grouping on. Total pages: 259958
[ 2.888901] Kernel command line: root=/dev/sda2 ro console=ttyS0
[ 2.974322] Dentry cache hash table entries: 262144 (order: 8, 2097152 bytes)
[ 3.066836] Inode-cache hash table entries: 131072 (order: 7, 1048576 bytes)
[ 3.151270] Sorting __ex_table...
[ 3.346086] Memory: 2069760K/2096048K available (4442K kernel code, 298K rwdata, 1096K rodata, 200K init, 278K bss, 26288K reserved, 0K cma-reserved)
[ 3.506677] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 3.585528] NR_IRQS: 2048, nr_irqs: 2048, preallocated irqs: 1
[ 3.655545] clocksource: hbtick: mask: 0xffffffffffffffff max_cycles: 0x148020aa9, max_idle_ns: 440795202069 ns
[ 3.776260] clocksource: mult[b400012e] shift[24]
[ 3.832470] clockevent: mult[16c16bf] shift[32]
[ 3.886908] Console: colour dummy device 80x25
[ 4.090118] Calibrating delay using timer specific routine.. 11.12 BogoMIPS (lpj=55648)
[ 4.185866] pid_max: default: 32768 minimum: 301
[ 4.241727] Mount-cache hash table entries: 4096 (order: 2, 32768 bytes)
[ 4.321958] Mountpoint-cache hash table entries: 4096 (order: 2, 32768 bytes)
[ 4.411687] devtmpfs: initialized
[ 4.456082] random: get_random_u32 called from bucket_table_alloc+0x78/0x1e0 with crng_init=0
[ 4.558763] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 4.676445] futex hash table entries: 256 (order: -1, 6144 bytes)
[ 4.750134] NET: Registered protocol family 16
[ 4.812677] IRQ pre handler NOT supported.
[ 4.862096] IRQ pre handler NOT supported.
[ 4.911395] IRQ pre handler NOT supported.
[ 4.961961] audit: initializing netlink subsys (disabled)
[ 5.033921] kworker/u2:0 (40) used greatest stack depth: 10304 bytes left
[ 5.115934] random: fast init done
[ 5.169855] /pci@1f,0: PCI IO [io 0x1fe02000000-0x1fe02ffffff] offset 1fe02000000
[ 5.260566] /pci@1f,0: PCI MEM [mem 0x1ff00000000-0x1ffffffffff] offset 1ff00000000
[ 5.352239] /pci@1f,0: SABRE PCI Bus Module ver[0:0]
[ 5.411653] PCI: Scanning PBM /pci@1f,0
[ 5.457965] sabre f005f408: PCI host bridge to bus 0000:00
[ 5.523589] pci_bus 0000:00: root bus resource [io 0x1fe02000000-0x1fe02ffffff] (bus address [0x0000-0xffffff])
[ 5.645351] pci_bus 0000:00: root bus resource [mem 0x1ff00000000-0x1ffffffffff] (bus address [0x00000000-0xffffffff])
[ 5.773361] pci_bus 0000:00: root bus resource [bus 00-01]
[ 5.839024] PCI: scan_bus[/pci@1f,0] bus no 0
[ 5.891179] * /pci@1f,0/ebus@c
[ 5.929908] create device, devfn: 60, type:
[ 5.985145] class: 0x68000 device name: 0000:00:0c.0
[ 6.048714] pci 0000:00:0c.0: [108e:1100] type 00 class 0x068000
[ 6.120606] adding to system ...
[ 6.163761] PCI: dev header type: 0
[ 6.205506] * /pci@1f,0/isa@7
[ 6.243152] create device, devfn: 38, type:
[ 6.298419] class: 0x60100 device name: 0000:00:07.0
[ 6.361991] pci 0000:00:07.0: [10b9:1533] type 00 class 0x060100
[ 6.433890] parse addresses (40 bytes) @ (ptrval)
[ 6.502673] start: 1fe02000000, end: 1fe0200ffff, i: 10
[ 6.567309] pci 0000:00:07.0: reg 0x10: [io 0x1fe02000000-0x1fe0200ffff]
[ 6.648557] start: 1ff00000000, end: 1ff000fffff, i: 14
[ 6.713192] pci 0000:00:07.0: reg 0x14: [mem 0x1ff00000000-0x1ff000fffff]
[ 6.794436] adding to system ...
[ 6.837517] PCI: dev header type: 0
[ 6.879234] * /pci@1f,0/pmu@3
[ 6.916881] create device, devfn: 18, type:
[ 6.972141] class: 0x0 device name: 0000:00:03.0
[ 7.031563] pci 0000:00:03.0: [10b9:7101] type 00 class 0x000000
[ 7.103460] parse addresses (20 bytes) @ (ptrval)
[ 7.172245] start: 1fe02000000, end: 1fe0200000f, i: 10
[ 7.236882] pci 0000:00:03.0: reg 0x10: [io 0x1fe02000000-0x1fe0200000f]
[ 7.318126] adding to system ...
[ 7.360970] pci 0000:00:03.0: quirk: [io 0x1fe02000800-0x1fe0200083f] claimed by ali7101 ACPI
[ 7.464025] pci 0000:00:03.0: quirk: [io 0x1fe02000600-0x1fe0200061f] claimed by ali7101 SMB
[ 7.566080] pci 0000:00:03.0: quirk_ali7101_acpi+0x0/0x40 took 19531 usecs
[ 7.648616] PCI: dev header type: 0
[ 7.690327] * /pci@1f,0/network@c,1
[ 7.734236] create device, devfn: 61, type: network
[ 7.796750] class: 0x20000 device name: 0000:00:0c.1
[ 7.860324] pci 0000:00:0c.1: [108e:1101] type 00 class 0x020000
[ 7.932219] parse addresses (40 bytes) @ (ptrval)
[ 8.001003] start: 1ff00400000, end: 1ff0041ffff, i: 10
[ 8.065640] pci 0000:00:0c.1: reg 0x10: [mem 0x1ff00400000-0x1ff0041ffff]
[ 8.146887] start: 1ff00800000, end: 1ff00bfffff, i: 30
[ 8.211522] pci 0000:00:0c.1: reg 0x30: [mem 0x1ff00800000-0x1ff00bfffff]
[ 8.292769] adding to system ...
[ 8.335825] PCI: dev header type: 0
[ 8.377569] * /pci@1f,0/firewire@c,2
[ 8.422489] create device, devfn: 62, type:
[ 8.477747] class: 0xc0010 device name: 0000:00:0c.2
[ 8.541326] pci 0000:00:0c.2: [108e:1102] type 00 class 0x0c0010
[ 8.613221] parse addresses (60 bytes) @ (ptrval)
[ 8.682007] start: 1ff00420000, end: 1ff00421fff, i: 10
[ 8.746642] pci 0000:00:0c.2: reg 0x10: [mem 0x1ff00420000-0x1ff00421fff]
[ 8.827891] start: 1ff00422000, end: 1ff00423fff, i: 14
[ 8.892525] pci 0000:00:0c.2: reg 0x14: [mem 0x1ff00422000-0x1ff00423fff]
[ 8.973775] start: 1ff00c00000, end: 1ff00ffffff, i: 30
[ 9.038411] pci 0000:00:0c.2: reg 0x30: [mem 0x1ff00c00000-0x1ff00ffffff]
[ 9.119656] adding to system ...
[ 9.162736] PCI: dev header type: 0
[ 9.204457] * /pci@1f,0/usb@c,3
[ 9.244184] create device, devfn: 63, type:
[ 9.299439] class: 0xc0310 device name: 0000:00:0c.3
[ 9.363017] pci 0000:00:0c.3: [108e:1103] type 00 class 0x0c0310
[ 9.434913] parse addresses (40 bytes) @ (ptrval)
[ 9.503701] start: 1ff02000000, end: 1ff02ffffff, i: 10
[ 9.568334] pci 0000:00:0c.3: reg 0x10: [mem 0x1ff02000000-0x1ff02ffffff]
[ 9.649582] start: 1ff01000000, end: 1ff013fffff, i: 30
[ 9.714218] pci 0000:00:0c.3: reg 0x30: [mem 0x1ff01000000-0x1ff013fffff]
[ 9.795464] adding to system ...
[ 9.838518] PCI: dev header type: 0
[ 9.880258] * /pci@1f,0/sound@8
[ 9.919990] create device, devfn: 40, type:
[ 9.975250] class: 0x40100 device name: 0000:00:08.0
[ 10.038823] pci 0000:00:08.0: [10b9:5451] type 00 class 0x040100
[ 10.110721] parse addresses (40 bytes) @ (ptrval)
[ 10.179506] start: 1fe02000900, end: 1fe020009ff, i: 10
[ 10.244142] pci 0000:00:08.0: reg 0x10: [io 0x1fe02000900-0x1fe020009ff]
[ 10.325391] start: 1ff00424000, end: 1ff00425fff, i: 14
[ 10.390026] pci 0000:00:08.0: reg 0x14: [mem 0x1ff00424000-0x1ff00425fff]
[ 10.471271] adding to system ...
[ 10.514119] pci 0000:00:08.0: supports D1 D2
[ 10.514131] pci 0000:00:08.0: PME# supported from D2 D3hot D3cold
[ 10.514430] PCI: dev header type: 0
[ 10.556172] * /pci@1f,0/ide@d
[ 10.593822] create device, devfn: 68, type: ide
[ 10.652205] class: 0x101ff device name: 0000:00:0d.0
[ 10.715780] pci 0000:00:0d.0: [10b9:5229] type 00 class 0x0101ff
[ 10.787672] parse addresses (100 bytes) @ (ptrval)
[ 10.857495] start: 1fe02000a00, end: 1fe02000a07, i: 10
[ 10.922130] pci 0000:00:0d.0: reg 0x10: [io 0x1fe02000a00-0x1fe02000a07]
[ 11.003380] start: 1fe02000a18, end: 1fe02000a1f, i: 14
[ 11.068016] pci 0000:00:0d.0: reg 0x14: [io 0x1fe02000a18-0x1fe02000a1f]
[ 11.149264] start: 1fe02000a10, end: 1fe02000a17, i: 18
[ 11.213900] pci 0000:00:0d.0: reg 0x18: [io 0x1fe02000a10-0x1fe02000a17]
[ 11.295150] start: 1fe02000a08, end: 1fe02000a0f, i: 1c
[ 11.359785] pci 0000:00:0d.0: reg 0x1c: [io 0x1fe02000a08-0x1fe02000a0f]
[ 11.441033] start: 1fe02000a20, end: 1fe02000a2f, i: 20
[ 11.505669] pci 0000:00:0d.0: reg 0x20: [io 0x1fe02000a20-0x1fe02000a2f]
[ 11.586915] adding to system ...
[ 11.629978] PCI: dev header type: 0
[ 11.671708] * /pci@1f,0/pci@5
[ 11.709365] create device, devfn: 28, type: pci
[ 11.767742] class: 0x60400 device name: 0000:00:05.0
[ 11.831315] pci 0000:00:05.0: [1011:0024] type 01 class 0x060400
[ 11.903210] adding to system ...
[ 11.946311] PCI: dev header type: 1
[ 11.988001] of_scan_pci_bridge(/pci@1f,0/pci@5)
[ 12.042236] Bridge bus range [1 --> 1]
[ 12.091470] Bridge ranges[ (ptrval)] simba[0]
[ 12.154985] RAW Range[81000000:00000000:00001000:81000000:00000000:00001000:00000000:00001000]
[ 12.262208] Using flags[00000101] start[0000000000001000] size[0000000000001000]
[ 12.356975] RAW Range[82000000:00000000:03000000:82000000:00000000:03000000:00000000:00100000]
[ 12.464201] Using flags[00000200] start[0000000003000000] size[0000000000100000]
[ 12.558963] bus name: PCI Bus 0000:01
[ 12.606967] PCI: scan_bus[/pci@1f,0/pci@5] bus no 1
[ 12.665361] * /pci@1f,0/pci@5/scsi@0
[ 12.710304] create device, devfn: 0, type:
[ 12.764510] class: 0x10000 device name: 0000:01:00.0
[ 12.828090] pci 0000:01:00.0: [1000:0001] type 00 class 0x010000
[ 12.899985] parse addresses (40 bytes) @ (ptrval)
[ 12.968770] start: 1fe02001000, end: 1fe020010ff, i: 10
[ 13.033408] pci 0000:01:00.0: reg 0x10: [io 0x1fe02001000-0x1fe020010ff]
[ 13.114655] start: 1ff03000000, end: 1ff03001fff, i: 14
[ 13.179290] pci 0000:01:00.0: reg 0x14: [mem 0x1ff03000000-0x1ff03001fff]
[ 13.260537] adding to system ...
[ 13.303636] PCI: dev header type: 0
[ 13.345332] * /pci@1f,0/pci@5/sound@1
[ 13.391308] create device, devfn: 8, type:
[ 13.445520] class: 0x40100 device name: 0000:01:01.0
[ 13.509093] pci 0000:01:01.0: [13f6:0111] type 00 class 0x040100
[ 13.580989] parse addresses (20 bytes) @ (ptrval)
[ 13.649773] start: 1fe02001100, end: 1fe020011ff, i: 10
[ 13.714410] pci 0000:01:01.0: reg 0x10: [io 0x1fe02001100-0x1fe020011ff]
[ 13.795654] adding to system ...
[ 13.838512] pci 0000:01:01.0: supports D1 D2
[ 13.838755] PCI: dev header type: 0
[ 13.880452] * /pci@1f,0/pci@5/sound@2
[ 13.926429] create device, devfn: 10, type:
[ 13.981678] class: 0x40100 device name: 0000:01:02.0
[ 14.045249] pci 0000:01:02.0: [1013:6005] type 00 class 0x040100
[ 14.117146] parse addresses (40 bytes) @ (ptrval)
[ 14.185931] start: 1ff03002000, end: 1ff03003fff, i: 10
[ 14.250568] pci 0000:01:02.0: reg 0x10: [mem 0x1ff03002000-0x1ff03003fff]
[ 14.331816] start: 1ff03010000, end: 1ff0301ffff, i: 14
[ 14.396450] pci 0000:01:02.0: reg 0x14: [mem 0x1ff03010000-0x1ff0301ffff]
[ 14.477696] adding to system ...
[ 14.520555] pci 0000:01:02.0: supports D1 D2
[ 14.520565] pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot
[ 14.520870] PCI: dev header type: 0
[ 14.562597] * /pci@1f,0/SUNW,m64B@13
[ 14.607528] create device, devfn: 98, type: display
[ 14.670066] class: 0x30000 device name: 0000:00:13.0
[ 14.733629] pci 0000:00:13.0: [1002:4752] type 00 class 0x030000
[ 14.805526] parse addresses (80 bytes) @ (ptrval)
[ 14.874311] start: 1ff04000000, end: 1ff04ffffff, i: 10
[ 14.938947] pci 0000:00:13.0: reg 0x10: [mem 0x1ff04000000-0x1ff04ffffff]
[ 15.020197] start: 1fe02000b00, end: 1fe02000bff, i: 14
[ 15.084831] pci 0000:00:13.0: reg 0x14: [io 0x1fe02000b00-0x1fe02000bff]
[ 15.166080] start: 1ff00426000, end: 1ff00427fff, i: 18
[ 15.230717] pci 0000:00:13.0: reg 0x18: [mem 0x1ff00426000-0x1ff00427fff]
[ 15.311966] start: 1ff00440000, end: 1ff0045ffff, i: 30
[ 15.376601] pci 0000:00:13.0: reg 0x30: [mem 0x1ff00440000-0x1ff0045ffff]
[ 15.457846] adding to system ...
[ 15.500698] pci 0000:00:13.0: supports D1 D2
[ 15.500959] PCI: dev header type: 0
[ 15.542832] pci 0000:00:0c.0: class 0x68000
[ 15.592936] PCI: Claiming 0000:00:07.0: Resource 0: 000001fe02000000..000001fe0200ffff [101]
[ 15.693943] pci 0000:00:07.0: can't claim BAR 0 [io 0x1fe02000000-0x1fe0200ffff]: address conflict with 0000:00:03.0 [io 0x1fe02000600-0x1fe0200061f]
[ 15.856232] PCI: Claiming 0000:00:07.0: Resource 1: 000001ff00000000..000001ff000fffff [200]
[ 15.957232] pci 0000:00:07.0: class 0x60100
[ 16.007314] PCI: Claiming 0000:00:03.0: Resource 0: 000001fe02000000..000001fe0200000f [101]
[ 16.108310] pci 0000:00:03.0: class 0x0
[ 16.154234] PCI: Claiming 0000:00:0c.1: Resource 0: 000001ff00400000..000001ff0041ffff [200]
[ 16.255231] PCI: Claiming 0000:00:0c.1: Resource 6: 000001ff00800000..000001ff00bfffff [44200]
[ 16.358309] pci 0000:00:0c.1: class 0x20000
[ 16.408389] PCI: Claiming 0000:00:0c.2: Resource 0: 000001ff00420000..000001ff00421fff [200]
[ 16.509387] PCI: Claiming 0000:00:0c.2: Resource 1: 000001ff00422000..000001ff00423fff [200]
[ 16.610384] PCI: Claiming 0000:00:0c.2: Resource 6: 000001ff00c00000..000001ff00ffffff [44200]
[ 16.713462] pci 0000:00:0c.2: class 0xc0010
[ 16.763541] PCI: Claiming 0000:00:0c.3: Resource 0: 000001ff02000000..000001ff02ffffff [200]
[ 16.864540] PCI: Claiming 0000:00:0c.3: Resource 6: 000001ff01000000..000001ff013fffff [44200]
[ 16.967617] pci 0000:00:0c.3: class 0xc0310
[ 17.017696] PCI: Claiming 0000:00:08.0: Resource 0: 000001fe02000900..000001fe020009ff [101]
[ 17.118693] PCI: Claiming 0000:00:08.0: Resource 1: 000001ff00424000..000001ff00425fff [200]
[ 17.219694] pci 0000:00:08.0: class 0x40100
[ 17.269774] PCI: Claiming 0000:00:0d.0: Resource 0: 000001fe02000a00..000001fe02000a07 [101]
[ 17.370772] PCI: Claiming 0000:00:0d.0: Resource 1: 000001fe02000a18..000001fe02000a1f [101]
[ 17.471768] PCI: Claiming 0000:00:0d.0: Resource 2: 000001fe02000a10..000001fe02000a17 [101]
[ 17.572766] PCI: Claiming 0000:00:0d.0: Resource 3: 000001fe02000a08..000001fe02000a0f [101]
[ 17.673762] PCI: Claiming 0000:00:0d.0: Resource 4: 000001fe02000a20..000001fe02000a2f [101]
[ 17.774763] pci 0000:00:0d.0: class 0x101ff
[ 17.824843] PCI: Claiming 0000:00:05.0: Resource 7: 000001fe02001000..000001fe02001fff [101]
[ 17.925839] PCI: Claiming 0000:00:05.0: Resource 8: 000001ff03000000..000001ff030fffff [200]
[ 18.026838] pci 0000:00:05.0: class 0x60400
[ 18.076919] PCI: Claiming 0000:00:13.0: Resource 0: 000001ff04000000..000001ff04ffffff [200]
[ 18.177916] PCI: Claiming 0000:00:13.0: Resource 1: 000001fe02000b00..000001fe02000bff [101]
[ 18.278914] PCI: Claiming 0000:00:13.0: Resource 2: 000001ff00426000..000001ff00427fff [200]
[ 18.379910] PCI: Claiming 0000:00:13.0: Resource 6: 000001ff00440000..000001ff0045ffff [44200]
[ 18.482987] pci 0000:00:13.0: class 0x30000
[ 18.533079] pci 0000:00:13.0: requesting [mem 0x1ff000a0000-0x1ff000bffff] from /pci@1f,0 [mem 0x1ff00000000-0x1ffffffffff]
[ 18.666284] pci 0000:00:13.0: can't claim VGA legacy [mem 0x1ff000a0000-0x1ff000bffff]: address conflict with 0000:00:07.0 [mem 0x1ff00000000-0x1ff000fffff]
[ 18.833774] PCI: Claiming 0000:01:00.0: Resource 0: 000001fe02001000..000001fe020010ff [101]
[ 18.934771] PCI: Claiming 0000:01:00.0: Resource 1: 000001ff03000000..000001ff03001fff [200]
[ 19.035769] pci 0000:01:00.0: class 0x10000
[ 19.085850] PCI: Claiming 0000:01:01.0: Resource 0: 000001fe02001100..000001fe020011ff [101]
[ 19.186849] pci 0000:01:01.0: class 0x40100
[ 19.236931] PCI: Claiming 0000:01:02.0: Resource 0: 000001ff03002000..000001ff03003fff [200]
[ 19.337928] PCI: Claiming 0000:01:02.0: Resource 1: 000001ff03010000..000001ff0301ffff [200]
[ 19.438926] pci 0000:01:02.0: class 0x40100
[ 19.496203] audit: type=2000 audit(0.320:1): state=initialized audit_enabled=0 res=1
[ 19.622228] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 19.702481] HugeTLB registered 8.00 MiB page size, pre-allocated 0 pages
[ 19.782649] HugeTLB registered 256 MiB page size, pre-allocated 0 pages
[ 19.861824] HugeTLB registered 2.00 GiB page size, pre-allocated 0 pages
[ 19.945112] pci 0000:00:13.0: vgaarb: command 0x0080
[ 20.004588] pci 0000:00:13.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
[ 20.104590] pci 0000:00:13.0: vgaarb: bridge control possible
[ 20.173340] pci 0000:00:13.0: vgaarb: setting as boot device (VGA legacy resources not enabled)
[ 20.277446] vgaarb: loaded
[ 20.310330] SCSI subsystem initialized
[ 20.357726] libata version 3.00 loaded.
[ 20.362515] /pci@1f,0/ebus@c/eeprom@1,0: Mostek regs at 0x1fff1000000
[ 20.440726] clocksource: Switched to clocksource hbtick
[ 20.520493] kworker/u2:2 (232) used greatest stack depth: 9104 bytes left
[ 20.628364] NET: Registered protocol family 2
[ 20.681769] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 16384 bytes)
[ 20.775592] TCP established hash table entries: 16384 (order: 4, 131072 bytes)
[ 20.862705] TCP bind hash table entries: 16384 (order: 4, 131072 bytes)
[ 20.942575] TCP: Hash tables configured (established 16384 bind 16384)
[ 21.021233] UDP hash table entries: 1024 (order: 2, 32768 bytes)
[ 21.093318] UDP-Lite hash table entries: 1024 (order: 2, 32768 bytes)
[ 21.171152] NET: Registered protocol family 1
[ 21.223437] pci 0000:00:07.0: Activating ISA DMA hang workarounds
[ 21.296401] pci 0000:00:07.0: quirk_isa_dma_hangs+0x0/0x40 took 71237 usecs
[ 21.379757] PCI: Enabling device: (0000:00:0c.3), cmd 2
[ 21.510825] pci 0000:00:0c.3: quirk_usb_early_handoff+0x0/0x740 took 127968 usecs
[ 21.600498] PCI: CLS 64 bytes, default 64
[ 21.600871] power: Control reg at 1fe02000800
[ 21.658494] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 21.787091] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 21.875693] io scheduler noop registered
[ 21.923116] io scheduler cfq registered (default)
[ 21.979998] PCI: Enabling device: (0000:00:13.0), cmd 83
[ 21.980065] atyfb: 3D RAGE XL (Mach64 GR, PCI-33) [0x4752 rev 0x27]
[ 22.055139] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL, 83 Mhz MCLK, 63 MHz XCLK
[ 22.211443] Console: switching to colour frame buffer device 80x30
[ 22.294364] atyfb: fb0: ATY Mach64 frame buffer device on PCI
[ 22.366227] f007d64c: ttyS0 at MMIO 0x1fe020003f8 (irq = 9, base_baud = 115387) is a 16550A
[ 22.466332] Console: ttyS0 (SU)
[ 22.504011] console [ttyS0] enabled
[ 22.591449] bootconsole [earlyprom0] disabled
[ 22.702383] f007f1a4: ttyS1 at MMIO 0x1fe020002e8 (irq = 9, base_baud = 115387) is a 16550A
[ 22.813941] PCI: Enabling device: (0000:00:0d.0), cmd 5
[ 22.820467] scsi host0: pata_ali
[ 22.864871] scsi host1: pata_ali
[ 22.907614] ata1: PATA max UDMA/66 cmd 0x1fe02000a00 ctl 0x1fe02000a18 bmdma 0x1fe02000a20 irq 15
[ 23.024268] ata2: PATA max UDMA/66 cmd 0x1fe02000a10 ctl 0x1fe02000a08 bmdma 0x1fe02000a28 irq 15
[ 23.143206] mousedev: PS/2 mouse device common for all mice
[ 23.219219] rtc-m48t59 rtc-m48t59.0: registered as rtc0
[ 23.288749] NET: Registered protocol family 17
[ 23.347160] Key type dns_resolver registered
[ 23.406899] registered taskstats version 1
[ 23.462916] Key type encrypted registered
[ 23.516861] rtc-m48t59 rtc-m48t59.0: setting system clock to 2018-04-11 20:18:18 UTC (1523477898)
[ 23.633992] ata1.00: ATA-5: ST320414A, 3.28, max UDMA/100
[ 23.704921] ata1.00: 39851760 sectors, multi 0: LBA
[ 23.770211] ata1.01: ATAPI: LTN486S, Y3S2, max UDMA/33
[ 23.837714] ata1.01: WARNING: ATAPI DMA disabled for reliability issues. It can be enabled
[ 23.947528] ata1.01: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
[ 24.060901] ata1.00: configured for UDMA/66
[ 24.118364] ata1.01: configured for UDMA/33
[ 24.174823] scsi 0:0:0:0: Direct-Access ATA ST320414A 3.28 PQ: 0 ANSI: 5
[ 24.283973] sd 0:0:0:0: [sda] 39851760 512-byte logical blocks: (20.4 GB/19.0 GiB)
[ 24.385464] scsi 0:0:1:0: CD-ROM LITEON CD-ROM LTN486S Y3S2 PQ: 0 ANSI: 5
[ 24.492621] sd 0:0:0:0: [sda] Write Protect is off
[ 24.555632] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 24.558277] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 24.686096] sda: sda1 sda2 sda3 sda4
[ 24.749770] sd 0:0:0:0: [sda] Attached SCSI disk
[ 24.847810] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 24.948613] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 25.064513] devtmpfs: mounted
[ 25.104639] This architecture does not have kernel memory protection.
[ 26.061161] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 26.236661] systemd[1]: Detected architecture 'sparc64'.
[ 26.671894] systemd[1]: Inserted module 'autofs4'
[ 26.800339] NET: Registered protocol family 10
[ 26.946140] modprobe (500) used greatest stack depth: 7200 bytes left
[ 27.090050] Segment Routing with IPv6
[ 27.138485] systemd[1]: Inserted module 'ipv6'
[ 27.210274] systemd[1]: Set hostname to <blade100>.
[ 27.970208] systemd-fstab-g (513) used greatest stack depth: 7000 bytes left
[ 28.590730] systemd-sysv-ge (518) used greatest stack depth: 6680 bytes left
[ 29.410697] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 29.609766] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 29.711102] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 29.810778] systemd[1]: Expecting device dev-ttyS0.device...
[ 29.950980] systemd[1]: Starting Remote File Systems (Pre).
[ 31.100922] systemd[1]: Listening on Journal Socket.
[ 31.166388] systemd[1]: Starting System Slice.
[ 31.280957] systemd[1]: Created slice System Slice.
[ 31.345305] systemd[1]: Starting File System Check on Root Device...
[ 31.495162] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 31.651043] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 31.736980] systemd[1]: Starting system-getty.slice.
[ 31.803873] systemd[1]: Created slice system-getty.slice.
[ 31.892349] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 31.991909] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 32.781823] loop: module loaded
[ 33.950896] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 34.594866] systemd-udevd[858]: starting version 215
[ 35.389844] /pci@1f,0/ebus@c/flashprom@0,0: OBP Flash, RD 1fff0000000[100000] WR 1fff0000000[100000]
[ 35.891041] usbcore: registered new interface driver usbfs
[ 35.963346] usbcore: registered new interface driver hub
[ 36.033281] usbcore: registered new device driver usb
[ 36.178897] PCI: Enabling device: (0000:00:03.0), cmd 1
[ 36.194250] PCI: Enabling device: (0000:01:00.0), cmd 3
[ 36.194997] sym0: <810a> rev 0x12 at pci 0000:01:00.0 irq 16
[ 36.282598] i2c i2c-0: Error: command never completed
[ 36.363542] alim7101_wdt: Steve Hill <steve@xxxxxxxxxxxx>
[ 36.434571] alim7101_wdt: Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter.
[ 36.671145] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 36.762362] random: crng init done
[ 36.896231] i2c i2c-0: Error: command never completed
[ 36.986450] sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
[ 37.069076] sym0: SCSI BUS has been reset.
[ 37.122903] scsi host2: sym-2.2.3
[ 37.190955] sr 0:0:1:0: [sr0] scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 37.287115] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 37.460994] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 37.615750] i2c i2c-0: Error: command never completed
[ 37.694838] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 37.697846] i2c i2c-0: Error: command never completed
[ 37.789344] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 37.881449] i2c i2c-0: Error: command never completed
[ 37.956046] i2c i2c-0: Error: command never completed
[ 38.032177] i2c i2c-0: Error: command never completed
[ 38.105769] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 38.192532] i2c i2c-0: Error: command never completed
[ 38.273178] i2c i2c-0: Error: command never completed
[ 38.348701] i2c i2c-0: Error: command never completed
[ 38.425577] i2c i2c-0: Error: command never completed
[ 38.493495] ehci-pci: EHCI PCI platform driver
[ 38.608019] i2c i2c-0: Error: command never completed
[ 38.676301] sungem.c:v1.0 David S. Miller <davem@xxxxxxxxxx>
[ 38.752290] gem 0000:00:0c.1 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:ba:0b:7d:5d
[ 38.892964] ohci-pci: OHCI PCI platform driver
[ 38.951551] ohci-pci 0000:00:0c.3: OHCI PCI host controller
[ 39.024840] ohci-pci 0000:00:0c.3: new USB bus registered, assigned bus number 1
[ 39.122190] ohci-pci 0000:00:0c.3: irq 13, io mem 0x1ff02000000
[ 39.271178] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.16
[ 39.379924] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 39.474909] usb usb1: Product: OHCI PCI host controller
[ 39.543571] usb usb1: Manufacturer: Linux 4.16.0-11316-gf77cfbe-dirty ohci_hcd
[ 39.638437] usb usb1: SerialNumber: 0000:00:0c.3
[ 39.709158] hub 1-0:1.0: USB hub found
[ 39.759851] hub 1-0:1.0: 4 ports detected
[ 39.823518] alim7101_wdt: Steve Hill <steve@xxxxxxxxxxxx>
[ 39.894525] alim7101_wdt: Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter.
[ 40.099630] alim7101_wdt: Steve Hill <steve@xxxxxxxxxxxx>
[ 40.170645] alim7101_wdt: Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter.
[ 42.770525] Adding 907664k swap on /dev/sda4. Priority:-2 extents:1 across:907664k
[ 43.331927] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 43.461921] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 44.086961] systemd-journald[848]: Received request to flush runtime journal from PID 1
[ 45.582986] sungem_phy: PHY ID: 437421, addr: 1
[ 45.583023] gem 0000:00:0c.1 eth0: Found Generic MII PHY
[ 45.653493] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 45.734391] ip (1089) used greatest stack depth: 6528 bytes left
[ 47.306788] systemd-udevd (871) used greatest stack depth: 5808 bytes left
[ 47.412708] systemd-udevd (863) used greatest stack depth: 4592 bytes left
[ 48.151054] gem 0000:00:0c.1 eth0: Link is up at 100 Mbps, full-duplex
[ 48.242519] gem 0000:00:0c.1 eth0: Pause is disabled
[ 48.311819] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
--
Meelis Roos (mroos@xxxxxxxx)
--
To unsubscribe from this list: send the line "unsubscribe sparclinux" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
