RE: Running anaconda - please wait...

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Dave,
 
Is the "portname:VLAN1" what is specified by the other Operating Systems that use that OSA card?  The "qeth: received an IDX TERMINATE on irq 0x10/0x11 with cause code 0x22 -- try another portname" message is usually only seen in cases where it doesn't match what the other systems are using.
 
Mark Post
 
-----Original Message-----
From: Dave Jeffs [mailto:DJEFFS@utah.gov]
Sent: Tuesday, November 26, 2002 1:57 PM
To: redhat-s390-list@redhat.com
Cc: Clair Christensen; Gilbert Jorgensen
Subject: Running anaconda - please wait...

I have been successful in installing RedHat 7.2 with the initrd.img file (2.4.9-37) and associated parm files for a qeth network connection.  This was accomplished with the script "RHSETUP"  This script however does NOT give me an option to perform a custom install.  From previous experience with the IUCF connection, I know that the script "LOADER" does give me that option. 
  
I am attempting install Linux RedHat 7.2 with a qeth network connection on our VM/Machine and am getting the following message when I attempt to use "LOADER".
 
I receive a message that netstg1.img is being loaded then I receive:
 
Running anaconda - please wait
 
Nothing else happens after that. 
 
The VM/Console has the following messages:
 
loop: loaded (max 8 devices)                     
VFS: Can't find ext2 filesystem on dev loop(7,0).
md: raid0 personality registered as nr 2         
md: raid1 personality registered as nr 3         
raid5: measuring checksumming speed              
   8regs     :   425.200 MB/sec                  
   32regs    :   334.400 MB/sec                  
raid5: using function: 8regs (425.200 MB/sec)    
md: raid5 personality registered as nr 4         
________________________________________________________________
 
Earlier in the IPL of the linux machine I do get the following messages.  I don't know if they have anythig to do with the problem at hand or not.  
 
qeth: Trying to use card with devnos 0xFF00/0xFF01/0xFF02                                        
qeth: Device 0xFF00/0xFF01/0xFF02 is an OSD Express card (level: 2938)                           
with link type Gigabit Eth (portname: VLAN1)                                                     
 qeth: IPv6 not supported on eth0                                                                
 qeth: Could not set up broadcast filtering on eth0: 0x2, continuing                             
qeth: Trying to use card with devnos 0xF400/0xF401/0xF402                                        
 qeth: received an IDX TERMINATE on irq 0x10/0x11 with cause code 0x22 -- try another portname   
 qeth: There were problems in hard-setting up the card.                                          
eth0      Link encap:Ethernet  HWaddr 00:00:00:00:00:00                                          
          inet addr:168.177.214.252  Mask:255.255.255.240                                        
          inet6 addr: fe80::200:ff:fe00:0/10 Scope:Link                                          
          UP RUNNING NOARP MULTICAST  MTU:1492  Metric:1                                         
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0                                     
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0                                   
          collisions:0 txqueuelen:100                                                            
          RX bytes:0 (0.0 b)  TX bytes:88 (88.0 b)                                               
          Interrupt:19  
 
_____________________________________________
 
my parm file looks like this:
 
root=/dev/ram0 ro ip=off                                                 
DASD=0200-020F                                                           
CHANDEV=qeth0,0xff00,0xff01,0xff02                                       
QETHPARM=add_parms,0x10,0xff00,0xff02,portname:VLAN1                     
HOST=lnxgsmst.its.state.ut.us:eth0:168.177.214.252:1492                  
NETWORK=168.177.214.240:255.255.255.240:168.177.214.255:168.177.214.241  
DNS=204.113.1.10                                                         
SEARCHDNS=its.state.ut.us                                                
RPMSERVER=ftp://168.179.248.137/RedHat/s390                              
DTZ=America/Denver                                                       
MOUNTS=/dev/dasdb1:/,/dev/dasdc1:/boot,/dev/dasdd1:/usr,/dev/dasde1:/opt 
_____________________________________________
 
Any help would be greatlly appreciated....
 
Dave Jeffs
djeffs@utah.gov
(801) 538-3506
 
 
                                                                          

[Index of Archives]     [Fedora General Discussion]     [LKML]     [Red Hat Install]     [Red Hat Watch]     [Red Hat Development]     [Linux s390]     [Gimp]     [Yosemite News]

  Powered by Linux