Here's more info from my VM guy on the loop/lockup after portmap starts.
Subject: RH 7.1 S/390 Loop
Chuck,
The looping instructions are
-> 0003425C' MVC D203A080C088 >> 02366080 020D4088 CC 2
00034262' LHI A718FFCF CC 2
-> 00034276' ST 5010C084 >> 020D4084 CC 1
0003427A' ST 5020C07C >> 020D407C CC 1
0003427E' MVC D203C0882080 >> 020D4088 02366080 CC 1
00034284' ICM BF1FC088 020D4088 CC 2
00034288' BRC A7840004 00034290 CC 2
0003428C' ST 50C01084 >> 020CC084 CC 2
00034290' L 5810C07C 020D407C CC 2
00034294' ST 50C01080 >> 02366080 CC 2
00034298' L 5820C000 020D4000 CC 2
0003429C' CHI A72E0004 CC 1
000342A0' BRC A7740008 -> 000342B0' CC 1
-> 000342B0' L 58B0C068 020D4068 CC 1
000342B4' C 59B0A068 02366068 CC 2
000342B8' BRC A784006E 00034394 CC 2
000342BC' L 5810C070 020D4070 CC 2
000342C0' C 5910A070 02366070 CC 2
000342C4' BRC A7740068 -> 00034394' CC 2
-> 00034394' ICM BFCFA080 02366080 CC 2
00034398' BRC A774FF62 -> 0003425C' CC 2
The loop usually (but not always) starts after the "Starting portmap"
message. In the above case I can break out of the loop using
#CP STORE S34398 A784FF62
The messages I then see are:
ctc0: connected with remote side
ctc0 Link encap:Serial Line IP
inet addr:169.10.253.163 P-t-P:169.10.253.161
Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:76 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
169.10.253.163 0.0.0.0 255.255.255.255 UH 0 0 0
ctc0
160.10.253.161 0.0.0.0 255.255.255.255 UH 0 0 0
ctc0
127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo
0.0.0.0 160.10.253.161 0.0.0.0 UG 0 0 0
ctc0
Starting portmap.
mount: mount point /mnt/target/proc does not exist
/sbin/init-203-: cannot create /mnt/target/tmp/169.10.253.163.ks: No such
file or directory
/sbin/init-205-: .: /mnt/target/tmp/169.10.253.163.ks: not found
In this state I can ping 169.10.253.163 but can't telnet, ftp.
Please forward this info to your friends at Redhat.
Best regards,
Mark
--
Chuck Milam, KF9FR
KF9FR@arrl.net
