Re: 3com 3c905b only at 10mb

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I have looked at modinfo, here's the output:

filename: /lib/modules/2.4.18-26.8.0/kernel/drivers/net/3c59x.o
description: "3Com 3c59x/3c9xx ethernet driver LK1.1.18-ac 1 July 2002"
author: "Donald Becker <becker@scyld.com>"
license: "GPL"
parm: debug int, description "3c59x debug level (0-6)"
parm: options int array (min = 1, max = 8), description "3c59x: Bits 0-3: media type, bit 4: bus mastering, bit 9: full duplex"
parm: full_duplex int array (min = 1, max = 8), description "3c59x full duplex setting(s) (1)"
parm: hw_checksums int array (min = 1, max = 8), description "3c59x Hardware checksum checking by adapter(s) (0-1)"
parm: flow_ctrl int array (min = 1, max = 8), description "3c59x 802.3x flow control usage (PAUSE only) (0-1)"
parm: enable_wol int array (min = 1, max = 8), description "3c59x: Turn on Wake-on-LAN for adapter(s) (0-1)"
parm: rx_copybreak int, description "3c59x copy breakpoint for copy-only-tiny-frames"
parm: max_interrupt_work int, description "3c59x maximum events handled per interrupt"
parm: compaq_ioaddr int, description "3c59x PCI I/O base address (Compaq BIOS problem workaround)"
parm: compaq_irq int, description "3c59x PCI IRQ number (Compaq BIOS problem workaround)"
parm: compaq_device_id int, description "3c59x PCI device ID (Compaq BIOS problem workaround)"
parm: watchdog int, description "3c59x transmit timeout in milliseconds"


I see the duplex settings. Also this driver is apparently not written specifically for this card.
-Scott

On Sunday, March 9, 2003, at 10:24 AM, Aaron Konstam wrote:

On Sun, Mar 09, 2003 at 08:29:40AM +0100, Bart SCHELSTRAETE wrote:
Scott Mugan wrote:

I have a 3c905b installed under RH8. It is only running at 10Mb. I
searched and found newer drivers for it but they need to be compiled
into modules. I followed the directions to the letter but I keep
getting tons of errors. The driver module that installs with RH8 is
for a 3c59x, I looked through the modinfo and could not figure out how
to set it for 100Mb instead of 10Mb, did I miss something?
TIA
-Scott
Hello,

Use 'mii-tool' for changing the speed.


rgrds,
             Bart
or use modinfo 3c905b
to see what parameters control this NIC speed.


--
-------------------------------------------
Aaron Konstam
Computer Science
Trinity University
715 Stadium Dr.
San Antonio, TX 78212-7200

telephone: (210)-999-7484
email:akonstam@trinity.edu



--
Psyche-list mailing list
Psyche-list@redhat.com
https://listman.redhat.com/mailman/listinfo/psyche-list



--
Psyche-list mailing list
Psyche-list@redhat.com
https://listman.redhat.com/mailman/listinfo/psyche-list

[Index of Archives]     [Fedora General Discussion]     [Red Hat General Discussion]     [Centos]     [Kernel]     [Red Hat Install]     [Red Hat Watch]     [Red Hat Development]     [Red Hat 9]     [Gimp]     [Yosemite News]

  Powered by Linux