This is incorrect about the Sun Sparc servers. On Sun Sparc servers, the machine itself has a MAC address and the banner command reports the machine's MAC address. Each NIC has its own MAC address. The Sun Sparc defaults to the machine's MAC address. In the NVRAM, a setting permits using either the machine's MAC address (the default) or the NIC's MAC address. The practice with Sun Sparc servers is to use the machine's MAC address unless there is a specific reason--such as, multiple NICs are used on the same subnet which would require separate MAC addresses. ifconfig can alter the MAC address used even further as stated previously. Also, the correct term is either at the "OBP" or at the "okay prompt". HTH On Fri, Oct 15, 2010 at 11:49 PM, frankzou <frankzou@xxxxxxxxxxxxx> wrote: > DEAR: > > On Sun Machine you can use command "banner" in OK mode. > > > > MSN:xiangdongzou2006@xxxxxxxxxxx <MSN%3Axiangdongzou2006@xxxxxxxxxxx> > > -----éäåä----- > åää: redhat-list-bounces@xxxxxxxxxx [mailto:redhat-list-bounces@xxxxxxxxxx] > äè Phebe_Mertes@xxxxxxxxxxxxxxxxx > åéæé: 2010-10-16 5:02 > æää: General Red Hat Linux discussion list > äé: Re: Find MAC address stored in NIC firmware > > redhat-list-bounces@xxxxxxxxxx wrote on 10/15/2010 03:17:41 PM: > > > From: Yong Huang <yong321@xxxxxxxxx> > > To: redhat-list@xxxxxxxxxx > > Date: 10/15/2010 03:50 PM > > Subject: Find MAC address stored in NIC firmware > > Sent by: redhat-list-bounces@xxxxxxxxxx > > > > The MAC address of an Ethernet network card can be changed with > > ifconfig or ip command. Correct me if wrong. But I think the real > > hardware address stored in the NIC firmware is not changed. How do I > > find the real MAC address? I checked ifconfig, ip, lspci, dmidecode, > > /sys/class/net/..., and ethtool. Most report whatever is shown by > > ifconfig, which could have been altered. The only possible solution > > is to dump EEPROM of NIC. > > > > For NIC using e1000 driver: > > > > # ifconfig eth3 | grep HW > > eth3 Link encap:Ethernet HWaddr 00:11:0A:56:81:B1 > > <-- We changed it to this earlier. > > # ethtool -e eth3 | head -3 <-- dump EEPROM > > Offset Values > > ------ ------ > > 0x0000 00 11 0a 56 81 b0 30 05 ff ff ff ff ff ff ff ff > > <-- first 6 bytes are HW address 00:11:0a:56:81:b0 > > # ifconfig eth3 hw ether 00:11:0a:56:81:ff <-- assign an arbitrary > one > > # ifconfig eth3 | grep HW > > eth3 Link encap:Ethernet HWaddr 00:11:0A:56:81:FF > > <-- ifconfig is fooled > > # ethtool -e eth3 | head -3 > > Offset Values > > ------ ------ > > 0x0000 00 11 0a 56 81 b0 30 05 ff ff ff ff ff ff ff ff > > <-- but firmware ignores it > > # ifconfig eth3 hw ether 00:11:0a:56:81:b1 <-- temporarily change it > > back to what we had > > # ll /sys/class/net/eth3/device/driver/ | grep module > > lrwxrwxrwx 1 root root 0 Oct 14 21:29 module -> ../../../../ > > module/e1000 <-- driver for it is e1000 > > # ethtool -i eth3 <-- another way to check driver > > driver: e1000 > > version: 7.3.21-k4.1-NAPI > > firmware-version: N/A > > bus-info: 0000:06:01.1 > > > > For a NIC using tg3 or bnx2 driver, the command has to be `ethtool - > > e eth1 length <some number>', otherwise I would get "Cannot get > > EEPROM data: Cannot allocate memory". Then the hw address is in the > > data or value column starting at some offset. The command output is > > long so has to be saved in a file to be view'ed with vi. > > > > Question: What's the correct way to find the original manufacturer's > > MAC address of an Ethernet card? > > > > Yong Huang > > On and HP server running RHEL5 you can search for the Ethernet controllers > in this output > > /sbin/lspci -vv | more > > [snip] > 03:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709 > Gigabit Ethernet (rev 20) > Subsystem: Hewlett-Packard Company NC382i Integrated Quad Port PCI > Express Gigabit Server Adapter > [snip] > Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port > 0 > Link: Latency L0s <4us, L1 <4us > Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- > Link: Speed 2.5Gb/s, Width x2 > **** Capabilities: [100] Device Serial Number 46-1b-8e-fe-ff-d1-e7-78 > Capabilities: [110] Advanced Error Reporting > Capabilities: [150] Power Budgeting > Capabilities: [160] Virtual Channel > > ## The MAC address will be 78:e7:d1:8e:1b:46 > > > play with this on a good machine. > Had to do this when all the disks pulled from one chassis and put into the > new chasis. The disks still had the old IP's in the ifcfg-eth# files > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > > __________ Information from ESET Smart Security, version of virus signature > database 5086 (20100504) __________ > > The message was checked by ESET Smart Security. > > http://www.eset.com > > > > > __________ Information from ESET Smart Security, version of virus signature > database 5086 (20100504) __________ > > The message was checked by ESET Smart Security. > > http://www.eset.com > > > > __________ Information from ESET Smart Security, version of virus signature > database 5086 (20100504) __________ > > The message was checked by ESET Smart Security. > > http://www.eset.com > > > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > This is incorrect about the Sun Sparc servers. On Sun Sparc servers, the machine itself has a MAC address and the banner command reports the machine's MAC address. Each NIC has its own MAX address. The Sun Sparc defaults to the machine's MAC address. -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
