I also forgot to mention you might need to adjust the type of bonding... I was using "alb" "active load balancing" so you might need another setting... trunking etc. the 1000 is miliseconds inbetween ethernet checks, also adjustable. --- On Wed, 2/25/09, ESGLinux <esggrupos@xxxxxxxxx> wrote: > From: ESGLinux <esggrupos@xxxxxxxxx> > Subject: Re: any tool to help configure bonding? > To: "General Red Hat Linux discussion list" <redhat-list@xxxxxxxxxx> > Date: Wednesday, February 25, 2009, 12:42 PM > Hello, > > I have tested your script and it worked like a charm, > > but when I try to restart the network I get the next > messages: > > Ethernet Channel Bonding Driver: v3.2.4 (January 28, 2008) > bonding: In ALB mode you might experience client > disconnections upon > reconnectio > n of a link if the bonding module updelay parameter (0 > msec) is incompatible > with the forwarding delay time of the switch > bonding: MII link monitoring set to 1000 ms > ADDRCONF(NETDEV_UP): bond0: link is not ready > bonding: bond0: Adding slave eth0. > eth0: link up > bonding: bond0: Error: dev_set_mac_address of dev eth0 > failed! ALB mode > requires > that the base driver support setting the hw address also > when the network > devic > e's interface is open > bonding: bond0: Adding slave eth1. > eth1: link up > bonding: bond0: Error: dev_set_mac_address of dev eth1 > failed! ALB mode > requires that the base driver support setting the hw > address also when the > network device's interface is open > > > If I run ifconfig I get the bond0 dev runing, but the > network doesnt work at > all, > > I think I´m doing something wrong but don´t not what > > any idea? > > thanks > > ESG > > > 2009/2/25 Thomas Fess <dfezz1@xxxxxxxxx> > > > > > All, > > > > Here is a script I wrote. No Support offered, but it > works great. > > just cut-n-paste into vi > > > > vi nicBonding.sh > > > > #!/bin/bash > > > > > ##################################################################### > > ################### DFEZZ1 Admin Scripts > ############################ > > ################### Must know your IP - Subnet and > Network ########## > > > ##################################################################### > > > > chdir="/etc/sysconfig/network-scripts" > > tmpdir="/tmp/" > > touch $chdir/ifcfg-bond0 > > > > echo -n "Enter 1st ethernet NIC > \"ethX\" " > > read ethX > > echo -n "Enter 2nd ethernet NIC > \"ethY\" " > > read ethY > > echo -n "Enter Prod IP address > \"prodIP\" " > > read prodIP > > echo -n "Enter Prod Network IP example > 192.168.1.0 \"prodNET\" " > > read prodNET > > echo -n "Enter Prod Gateway IP > \"prodGW\" " > > read prodGW > > > > cp $chdir/ifcfg-$ethX $tmpdir/ifcfg-$ethX_orig > > cp $chdir/ifcfg-$ethY $tmpdir/ifcfg-$ethY_orig > > > > cat > $chdir/ifcfg-bond0 << EOF > > DEVICE=bond0 > > IPADDR=$prodIP > > NETMASK=255.255.255.0 > > NETWORK=$prodNET > > NETWORKING_IPV6=no > > GATEWAY=$prodGW > > USERCTL=no > > BOOTPROTO=none > > ONBOOT=yes > > EOF > > cat > $chdir/ifcfg-$ethX << EOF > > DEVICE=$ethX > > ONBOOT=yes > > USERCTL=no > > MASTER=bond0 > > SLAVE=yes > > BOOTPROTO=none > > TYPE=Ethernet > > EOF > > cat > $chdir/ifcfg-$ethY << EOF > > DEVICE=$ethY > > USERCTL=no > > ONBOOT=yes > > MASTER=bond0 > > SLAVE=yes > > BOOTPROTO=none > > TYPE=Ethernet > > EOF > > > > cat >> /etc/modprobe.conf << EOF > > alias bond0 bonding > > options bond0 mode=balance-alb miimon=1000 > > EOF > > > > cat > /etc/sysconfig/network-scripts/route-bond0 > << EOF > > GATEWAY0=$prodGW > > NETMASK0=255.255.255.0 > > ADDRESS0=$prodNET > > EOF > > > > echo -n "Run ... service network restart ... and > the bonding will take > > effect" > > > > > #################################################################### > > > > > > --- On Tue, 2/24/09, ESGLinux > <esggrupos@xxxxxxxxx> wrote: > > > > > From: ESGLinux <esggrupos@xxxxxxxxx> > > > Subject: any tool to help configure bonding? > > > To: "General Red Hat Linux discussion > list" <redhat-list@xxxxxxxxxx> > > > Date: Tuesday, February 24, 2009, 11:28 AM > > > Hi all, > > > > > > Im trying to configure 2 ethernet cards to use > bonding to > > > increase the > > > throughput. > > > > > > I´m using > /usr/share/doc/iputils-20020927/README.bonding > > > to learn how to do > > > it, but I have a question > > > > > > With system-config-network is it posible to do > it? or I > > > have to manually > > > edit the files in /etc/sysconfig/ > > > > > > Thanks > > > > > > ESG > > > -- > > > redhat-list mailing list > > > unsubscribe > > > > mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > > > > > -- > > redhat-list mailing list > > unsubscribe > mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > -- > redhat-list mailing list > unsubscribe > mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
