On 3/31/08, Gerrard Geldenhuis <Gerrard.Geldenhuis@xxxxxxxxxxxx> wrote: > Leaving the values won't confuse the bonding driver. I leave them > specifically because that helps to tie down interface so they are always > the same. eth0 will thus always be the same physical interface and so > on. i normally do this in modprobe.conf as something hinky happens on dells with more than 2 ethernet ports and udev :-) > > Can you point me to the documentation that supports removing hwaddr > lines... It is also likely that the manipulation of configuration files > differs from distro to distro... > http://www.linuxquestions.org/linux/answers/Networking/Linux_bonding_howto_0 also from bonding.txt All interfaces that are part of the trunk, should have SLAVE and MASTER definitions. For example, in the case of RedHat, if you wish to make eth0 and eth1 (or other interfaces) a part of the bonding interface bond0, their config files (ifcfg-eth0, ifcfg-eth1, etc.) should look like this: DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none from bond_main.c 16 * How it works: 17 * ifconfig bond0 ipaddress netmask up 18 * will setup a network device, with an ip address. No mac address 19 * will be assigned at this time. The hw mac address will come from 20 * the first slave bonded to the channel. All slaves will then use 21 * this hw mac address. 22 * 23 * ifconfig bond0 down 24 * will release all slaves, marking them as down. 25 * 26 * ifenslave bond0 eth0 27 * will attach eth0 to bond0 as a slave. eth0 hw mac address will either 28 * a: be used as initial mac address 29 * b: if a hw mac address already is there, eth0's hw mac address 30 * will then be set from bond0. 31 * The only reason i think this is that i have had problems with bonding with RH5.1 where i had the HWADDR values specified. bond0 wouldn't come up until i removed - indeed the box wouldn't boot - until i removed those lines from ifcfg-eth0 and 1 I could be wrong, i often am best wishes mike > The bonding driver documentation states that you can specify options for > the bond interface in the ifcfg-bondX file but that has not been the > case for me. I still have to specify options in the /etc/modprobe.conf > file. > > Regards > > > -----Original Message----- > > From: redhat-list-bounces@xxxxxxxxxx [mailto:redhat-list- > > bounces@xxxxxxxxxx] On Behalf Of Michael Simpson > > Sent: 31 March 2008 13:35 > > To: General Red Hat Linux discussion list > > Subject: Re: NIC Teaming > > > > On 3/27/08, Gerrard Geldenhuis <Gerrard.Geldenhuis@xxxxxxxxxxxx> > wrote: > > > Hi Vivek, > > > It is also called bonding which might yield better results in > google. > > > > > > It is actually very simple: > > > Create a new file called ifcfg-bond0 in > /etc/sysconfig/network-scripts/ > > > with the following data inside: > > > DEVICE=bond0 > > > BOOTPROTO=static > > > ONBOOT=yes > > > IPADDR=Your ip here > > > NETMASK=Your netmask here > > > > > > In the interface that you want as part of the bond edit the > appropriate > > > file. For example ifcfg-eth0 and ifcfg-eth2 which can also be found > in > > > /etc/sysconfig/network-scripts/ > > > > > > You should edit out the ip address and netmask. Make sure the > bootproto > > > is none, keep the hardware address, add slave=yes and add > master=bond0 > > > > > > DEVICE=eth0 > > > BOOTPROTO=none > > > HWADDR=AA:AA:C4:BE:AA:AA > > > ONBOOT=yes > > > TYPE=Ethernet > > > SLAVE=yes > > > MASTER=bond0 > > > > > > > Hi there > > > > i thought that you were meant to remove the HWADDR= lines from > > ifcfg-eth0 and ifcfg-eth1 as bonding manipulates these values to make > > the necessary arp magic work. > > > > the documentation seems to support this view. > > > > mike > > > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
