The output of command #lspci -vv is
----------------------------------------
pcilib: Resource 3 in /sys/bus/pci/devices/0000:00:00:0/resource has a
64-bit address, ignoring
00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a33 (rev 01)
Subsystem: Intel Corporation: Unknown device d600
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [b0] #0d [0000]
00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at fdf80000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
(rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at fa00 [size=8]
Region 1: I/O ports at f900 [size=4]
Region 2: I/O ports at f800 [size=8]
Region 3: I/O ports at f700 [size=4]
Region 4: I/O ports at f600 [size=16]
Region 5: Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at fdf80000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 185
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 185
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(rev 80) (prog-if 20 [EHCI])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 20
Interrupt: pin A routed to IRQ 185
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 0b00 [size=16]
Region 1: Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at f400 [size=16]
Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00:14.2 Class 0403: ATI Technologies Inc: Unknown device 437b (rev 01)
Subsystem: Intel Corporation: Unknown device d600
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 193
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: fdc00000-fdcfffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5a61
(prog-if 00 [VGA])
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 201
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at ee00 [size=256]
Region 2: Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Intel Corporation: Unknown device d600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 209
Region 0: I/O ports at de00 [size=256]
Region 1: Memory at fddff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09) (prog-if
02 [16550])
Subsystem: Unknown device 2205:2004
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 201
Region 0: Memory at fddfe000 (32-bit, non-prefetchable) [size=4K]
------------------------------------
On 2/12/08, Vivek Mangal <vivek.mangal9685@xxxxxxxxx> wrote:
>
> hello all,
> My new PC show a message all time at the booting
> i can not under stand what is the problem ?
> and how can i recover it ?
> problem is that
>
> PCI: cannot allocate resource region 3 of devices 0000:00:00:0
>
> if any have any idea then please tell me.
>
--
redhat-list mailing list
unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/redhat-list
