further to that, Would a separate partition for /tmp be in order? I remember a message about two weeks ago alluding to the fact that by putting /tmp on its own partition, Nagarjuna Rao Cherukuri noticed an increase in performance. Should I take this as a rule, or an anecdote? Regards, -G -----Original Message----- From: Burke, Thomas G. [mailto:tg.burke@xxxxxxx] Sent: Friday, August 05, 2005 10:05 AM To: me@xxxxxxxxxxxx; General Red Hat Linux discussion list Subject: RE: SATA RAID controller recommendations I have no direct experience, but I have been told that it took leavng an IDE in to do the installs, so the installers could detect. However, he installed to the SATA's, and set them up as the boot partitions. He claimed it worked after that, but I can't recall if he left the IDE in or if he took it out. It may have amounted to using the ide strictly as a boot device (and maybe swap space). He also told me that he was seeing ~25-50% disk performance improvement using the SATA's. Sorry, that's the only intel I've got. -Tom -----Original Message----- From: redhat-list-bounces@xxxxxxxxxx [mailto:redhat-list-bounces@xxxxxxxxxx] On Behalf Of Gavin McDonald Sent: Friday, August 05, 2005 12:56 PM To: 'General Red Hat Linux discussion list' Subject: RE: SATA RAID controller recommendations Just to add my 2c: I recently tried getting RHEL to work on a dual-opteron ASUS board, with dual onboard SATA hardware raid controllers. One was part of the NVIDIA chipset, the other was a "Silicon Image" Controller. Long story short, I replaced the SATA drives with IDE drives instead. To start with, I couldn't boot a stable kernel off of the original Red CDs (Box-Set), so I d/l the latest RHEL3 ISOs, which at least booted. (We're a '3' shop until I can migrate _everything_ to 4...). Now with a stable kernel, the Mfr-Supplied Driver disks were still useless. Not once was I able to boot to the install GUI, unless I had an IDE drive attached as well. If you can go to RHEL4, the controllers are detected, and the drives appear in disk druid, however, even with the hardware BIOS setup for RAID0 or RAID1, the druid shows 2 separate drives... So that was my tale of woe, If someone has had better experiences with either controller, or perhaps notices a flaw in my logic, (gasp!) please feel free to tell me so. :) (This is after all, a mailing list ;) Regards, -G -----Original Message----- From: redhat-list-bounces@xxxxxxxxxx [mailto:redhat-list-bounces@xxxxxxxxxx] On Behalf Of Chris Sent: Tuesday, August 02, 2005 3:15 PM To: redhat-list@xxxxxxxxxx Subject: Re: SATA RAID controller recommendations Michael's Stationery----- Original Message ----- From: Michael Cohn Sent: Tuesday, August 02, 2005 2:54 PM Subject: SATA RAID controller recommendations > I just saw your post from back in November regarding SATA RAID > controller recommendations. > > http://info.ccone.at/INFO/Mil-Archives/redhat/Nov-2004 > /msg00119.html > > What controller did you wind up using? I just purchsaed a Dell > PowerEdge 420sc with 2x80gb SATA drives and would like to add a > hardware RAID controller. My plan is to run either Fedora 3/4 or > SuSe. Michael, By far the best SATA RAID controllers with great support for Linux come from 3WARE. If you only have 2 drives, you can get away with their basic (~$120) model which can do RAID-0 and RAID-1, the 8006-2LP. It works great! We have everything they make from the basic 2-port model all the way up to a 12-port models which run our 3TB storage backup systems. Stay away from Adaptec and Promise controllers. Promise controllers have serious issues with drivers and stability, while Adaptec outright abandons brand new products and doesn't provide almost any Linux support. We had to toss several dozen of their 'brand new' zero channel SCSI RAID 2015S controllers because they announced that they would not provide drivers for kernel 2.6 - meaning FC2 and above, RHEL 4, etc. They seem to be a "Windows only" shop these days. I know it has nothing to do with SATA, but as a company in general I wouldn't buy any of their products anymore, not after spending thousands on controllers that we had to replace less than 6 months later because Adaptec decided they were going to support Windows only. Chris -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
