----- Original Message ----- From: "Rigler, Stephen C." <srigler@xxxxxxxxxxxxxxx> Date: Thursday, February 24, 2005 4:22 am Subject: Re: Problem with installation of Qlogic 2310F FC card!!! > On Wed, 2005-02-23 at 23:49 -0800, Govind C wrote: > > > > Why is not recognizing the FC channel?Am very sure its a > Qla2310f FC > > card. > > > > Cheers > > > > Assuming you really do have a Ql23xx card, it should show up in the > output of "lspci -v": > > 06:01.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev > 02) > Subsystem: QLogic Corp.: Unknown device 0100 > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11 > I/O ports at 4000 [size=256] > Memory at f7ff0000 (64-bit, non-prefetchable) [size=4K] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: <available only to root> > > 06:02.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev > 02) > Subsystem: QLogic Corp.: Unknown device 0100 > Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 7 > I/O ports at 4400 [size=256] > Memory at f7fe0000 (64-bit, non-prefetchable) [size=4K] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: <available only to root> > > Not to mention the messages you'd see after powering on the machine. > > -Steve > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > Still no luck #more/etc/modules.conf alias eth0 tg3 alias eth1 tg3 alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptscsih alias usb-controller usb-ohci post-remove qla2300 rmmod qla2300_conf alias scsi_hostadapter2 qla2300 alias scsi_hostadapter3 qla2300_conf alias scsi_hostadapter4 qla2300 alias scsi_hostadapter5 qla2300_conf alias scsi_hostadapter5 sg options qla2300 ql2xmaxqdepth=16 qlport_down_retry=16 qlogin_retry_count=16 ql2xfailover=1 #lspci -v 29:01.0 Fibre Channel: QLogic Corp.: Unknown device 0300 (rev 01) Subsystem: QLogic Corp.: Unknown device 0106 Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 40 I/O ports at 3000 [size=256] Memory at e8001000 (64-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [44] Power Management version 2 Capabilities: [4c] PCI-X non-bridge device. Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable #modprobe qla2300 /lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: insmod /lib/modules/2.4.21- 4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o failed /lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: insmod qla2300 failed -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
