Re: Router problems on Redhat 9.0 Linux 2.4.20-13.9.HOSTAP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On April 15, 2004 12:21 am, Yann Garcia wrote:
> Hi,
>
> On my Linux box, I have two network interfaces: a LAN interface (eth0) and
> a WLAN (wlan0). I set ip forwarding in /etc/sysctl.conf. I start a sniffer
> (tethereal) on both interfaces. When I make a ping from WLAN network to LAN
> network, ping donâ cross my gateway. The networks infos are:
> eth0: 10.0.1.37/16
> wlan0: 10.0.10.1/24
> The route tables are (netstat ârn):
>          Destination     Passerelle      Genmask         Indic   MSS
> Fenetre irtt Iface 10.0.10.0       0.0.0.0         255.255.255.0   U       
>  0 0          0 wlan0 10.0.0.0        0.0.0.0         255.255.0.0     U    
>     0 0          0 eth0 169.254.0.0     0.0.0.0         255.255.0.0     U  
>       0 0          0 wlan0 127.0.0.0       0.0.0.0         255.0.0.0      
> U         0 0          0 lo 0.0.0.0         10.0.0.1        0.0.0.0        
> UG        0 0          0 eth0
>
> The iptables rules are (iptables âL ân âv):
>          Chain INPUT (policy ACCEPT 17346 packets, 1205K bytes)
>           pkts bytes target     prot opt in     out     source             
>  destination
>
>          Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
>           pkts bytes target     prot opt in     out     source             
>  destination
>
>          Chain OUTPUT (policy ACCEPT 17144 packets, 1306K bytes)
>           pkts bytes target     prot opt in     out     source             
>  destination
>
> Iâm sorry but I donât understand why my gateway doesnât work!
>
> Thank you very much for your assistance,
>
> Best regards,
>
> Yann Garcia
> Software Engineer
>
> SmartCom
> 400, Av Roumanille - BP 309
> 06906 Sophia Antipolis Cedex
> France
>
> Tel: +33 493 008 746
> Fax: +33 493 001 101
> Mail: yann.garcia@xxxxxxxxxxxx
> Site: www.smartcom.com


Hi,
Your eth0's network contains of the wlan IP range.
10.0.1.37/16 is part of a network ip range of 10.0.0.1 to 10.0.255.254
Your wlan range is inside that so no routing is performed.

You want to use a class C range for the wlan, so instead of 10.0.10.0 network, 
try using one of the 192.168. class C networks. It may make be best to use 2 
different 192.168 networks (say 192.168.0.0/24 for LAN and 192.168.1.0/24 for 
the WLAN). 

Class A 1.0.0.0 - 127.255.255.255
Class B 128.0.0.0 - 191.255.255.255
Class C  192.0.0.0 - 223.255.255.255

Hope that helps.
-- 
Pete Nesbitt, rhce


-- 
redhat-list mailing list
unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/redhat-list

[Index of Archives]     [CentOS]     [Kernel Development]     [PAM]     [Fedora Users]     [Red Hat Development]     [Big List of Linux Books]     [Linux Admin]     [Gimp]     [Asterisk PBX]     [Yosemite News]     [Red Hat Crash Utility]


  Powered by Linux