Yes, with ntfs I get this: fs type ntfs not supported by kernel. I suppose that task (enable NTFS in the kernel) is quite difficult, is it? On SÃb, 2003-10-04 at 17:14, Jason Staudenmayer wrote: > You have to enable NTFS in the kernel I don't think it come turned on by > default. Also you will only be able to read from it. Try "mount -t ntfs > /dev/hdd1 /mnt/alf" if it bitches about the filesystem or module then you'll > have to recompile your kernel. > > -----Original Message----- > From: Paula Fernandes [mailto:paula@xxxxxxx] > Sent: Saturday, October 04, 2003 12:16 PM > To: redhat-list@xxxxxxxxxx > Subject: RE: Mount new disk... > > > The drive is set to slave on the second IDE. > > There are 2 partitions in that disk. The first one is NTFS, and the > second is FAT. The important one (with the data) is the first one > (NTFS). > > > On SÃb, 2003-10-04 at 17:01, Jason Staudenmayer wrote: > > Are you sure it detected it as hdd and not hdc. If the drive is set to > > master it will be hdc. Is the something else on the second IDE channel? > How > > many partitions are on the drive your looking to mount? > > > > -----Original Message----- > > From: Paula Fernandes [mailto:paula@xxxxxxx] > > Sent: Saturday, October 04, 2003 12:00 PM > > To: redhat-list@xxxxxxxxxx > > Subject: Re: Mount new disk... > > > > > > > > I get the same answer. > > > > I am using RedHat 9.0 > > > > On SÃb, 2003-10-04 at 16:54, Jeff Wimmer wrote: > > > I believe you need to do the following, although you didn't say which > > > version of redhat you're running: > > > > > > mount -t vfat /dev/hdd /mnt/alf > > > > > > > > > JEFFREY WIMMER > > > ----- Original Message ----- > > > From: "Paula Fernandes" <paula@xxxxxxx> > > > To: <redhat-list@xxxxxxxxxx> > > > Sent: Saturday, October 04, 2003 10:44 AM > > > Subject: Mount new disk... > > > > > > > > > > > > > > Hi list, > > > > > > > > > > > > I need to mount a disk with a windows system to recover some files > from > > > > the disk. I plug it into the secondary IDE has slave. > > > > > > > > I have created a new directory this way: > > > > > > > > mkdir /mnt/alf > > > > > > > > Then I try to mount the disk this way: > > > > > > > > mount /dev/hdd /mnt/alf > > > > > > > > And I get this answer: /dev/hdd is not a valid block device > > > > > > > > Then I try /dev/hdd0 and hdd1, and the answer still the same. > > > > > > > > > > > > Do I need to give any other instruction the the mount command? > > > > > > > > Thanks for any help... > > > > > > > > > > > > > > > > > > > > > > > > -- > > > > redhat-list mailing list > > > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > > > > > > > > > > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
