Use of the tool...... When you put the wires into the RJ-45 cap, you then insert the cable with cap on it into the squisher part of the crimper. It should only fit one way. Crossover, is where the cable goes out on friday with a big wig..... Or when you need to connect two computers without a router. It crosses the in and out cables, so the in of one, is the in of another. The pairs on a crossover will be DIFFERENT on both sides of the cable. -----Original Message----- From: Harold Martin [mailto:cocoadev@xxxxxxxxxxxxx] Sent: Friday, October 03, 2003 4:22 PM To: redhat-list@xxxxxxxxxx Subject: RE: Using RJ45 crimp tool Whew! I think I understand the ordering of the wires now, but I still have two questions: 1. How to actually *use* the tool itself 2. (kinda stupid, I know) what is the diff between crossover and patch cables and when should either be used? I really appreciate all your help. Harold On Fri, 2003-10-03 at 12:16, Chris Wilson wrote: > The order previously stated below does a good job for reducing noise if > you use this cable for Telephone or Ethernet. With that pin-out the T/R > pin are twisted together and the A1/A2 pins are twisted together so you > get a better Common Mode Noise Rejection which makes it suitable for > Telco or Network (<= 100Mb/s). > > But I do believe the TIA568A (see 568B for cross over) standard colors > are: > 1 White Green (Ether TX+ 1) > 2 Green (Ether TX- 2) > 3 White Orange (RX+ 3 / Telco A1) > 4 Blue (Telco TIP) > 5 White Blue (Telco Ring) > 6 Orange (Ether- 6 / Telco A2) > 7 White Borwn > 8 Borwn > > -- Chris > > On Fri, 2003-10-03 at 13:38, Jason Staudenmayer wrote: > > I think order does matter or at least the pairs match. I have had some hand > > made cables crap out due to "what ever wire straight through". You get > > "cross talk" across the pairs and wind up with weird issues. > > > > -----Original Message----- > > From: Nick White [mailto:nwhite@xxxxxxxxxxx] > > Sent: Friday, October 03, 2003 2:37 PM > > To: redhat-list@xxxxxxxxxx > > Subject: RE: Using RJ45 crimp tool > > > > > > Pin 1 is on the left if the "hook" is on the bottom. Like an earlier > > poster said, it really doesn't matter what color goes where, as it's the > > order that counts. The most common standard used these days (568B) is > > as Harold pointed out: > > > > 1 White-orange > > 2 Orange > > 3 White-green > > 4 Blue > > 5 White-blue > > 6 Green > > 7 White-brown > > 8 Brown > > > > It's also worth mentioning that if you want to make a crossover cable, > > just swap the orange and green pairs on 1 end of the cable. > > > > > -----Original Message----- > > > From: cajun [mailto:cajunlee@xxxxxxxxxx] > > > Sent: Friday, October 03, 2003 11:18 AM > > > To: redhat-list@xxxxxxxxxx > > > Subject: Re: Using RJ45 crimp tool > > > > > > > > > Harold Martin wrote: > > > > > > >Hello, > > > >Can anyone point mt toward a how-to on using an RJ45 crimp tool? > > > >Thanks, > > > >Harold > > > > > > > > > > > > > > > > > > > Hi Harold, > > > > > > I don't think there is any how to on that. What are you > > > needing to know > > > exactly? Or you needing to know the pin out for the wiring? > > > If so here > > > is what I have always used: > > > > > > Pin No. Strand Color > > > 1 white & orange > > > 2 orange > > > 3 white & green > > > 4 blue > > > 5 white & blue > > > 6 green > > > 7 white & brown > > > 8 brown > > > > > > HTH!! > > > > > > Lee Perez > > > > > > > > > -- > > > redhat-list mailing list > > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > > > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
