On Thu, 2011-05-05 at 10:21 -0400, cliff here wrote: > *** Update *** > > So I took the switch out of a rack and hooked it up to a workstation with > the exact same hardware using the exact same build of RHEL, ONLY difference > is that this machine had X installed. Worked the first time. Now, is there > some difference in the way that minicom interprets a tty console vice the > 'terminal' prog in X? > > On Wed, May 4, 2011 at 6:20 PM, Grzegorz Witkowski <geslinux@xxxxxxxxx>wrote: > > > On Wed, 2011-05-04 at 16:16 -0400, cliff here wrote: > > > Yea it's set to 9600, like i said I"m duplicating the same settings I > > used > > > in hyperterm that worked fine. > > > > > > On Wed, May 4, 2011 at 3:40 PM, Grzegorz Witkowski <geslinux@xxxxxxxxx > > >wrote: > > > > > > > On Wed, 2011-05-04 at 15:18 -0400, cliff here wrote: > > > > > Good afternoon list compatriots; > > > > > > > > > > Having a weird issue using minicom to connect a 2400 series Procurve > > > > > switch. I am using 8N1 and I start by leaving minicom listening and > > then > > > > > reboot the switch. > > > > > > > > > > Switch comes up and I see it's ROM decompress and post, then asks me > > to > > > > hit > > > > > enter twice to confirm speed test. However minicom doesn't seem to be > > > > > responding to any keystrokes. I believe the terminal emulation is > > set to > > > > > VT102. > > > > > > > > > > The other item that seems odd is that even though I can see output > > from > > > > the > > > > > switch minicom still says 'offline' > > > > > > > > > > I know my settings are correct since I've used hyperterm to get it > > > > working > > > > > before, I'm assuming I just am not understanding a setting or > > behavior of > > > > > minicom. > > > > > > > > > > -- > > > > > > > > > > > ------------------------------------------------------------------------------------------------------------------------------------- > > > > > NOTICE: This message, including all attachments, is intended for the > > use > > > > of > > > > > the individual or entity to which it is addressed and may contain > > > > > information that is privileged, confidential and exempt from > > disclosure > > > > > under applicable law. If the reader of this message is not the > > intended > > > > > recipient, or the employee or agent responsible for delivering this > > > > message > > > > > to its intended recipient, you are hereby notified that any > > > > dissemination, > > > > > distribution or copying of this communication is strictly prohibited. > > If > > > > you > > > > > have received this communication in error, please notify the sender > > > > > immediately by replying "Received in error" and immediately delete > > this > > > > > message and all its attachments. > > > > > > > > > > > ------------------------------------------------------------------------------------------------------------------------------------- > > > > > > > > Hi, > > > > > > > > You did not say anything about boud rate and flow control. > > > > They are very important. Typically you set flow control to none when > > > > connecting to switches. Check documentation of your switch for baud > > > > rate. Usually it's 9600, but some switches may have 115200 default. > > > > If those are incorrect, you may see connection problems. > > > > > > > > Hope this will help. > > > > > > > > Regards, > > > > Ges > > > > -------------------------------------------------------------- > > > > 01000111 01100101 01110011 01100011 01100001 01110000 01100101 > > > > http://counter.li.org #239224 Registration 2001-10-29 07:19:32 > > > > -= GNU/Linux - The Experience of Freedom =- > > > > > > > > -- > > > > redhat-list mailing list > > > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > > > > > > > > > > > -- > > > > > ------------------------------------------------------------------------------------------------------------------------------------- > > > NOTICE: This message, including all attachments, is intended for the use > > of > > > the individual or entity to which it is addressed and may contain > > > information that is privileged, confidential and exempt from disclosure > > > under applicable law. If the reader of this message is not the intended > > > recipient, or the employee or agent responsible for delivering this > > message > > > to its intended recipient, you are hereby notified that any > > dissemination, > > > distribution or copying of this communication is strictly prohibited. If > > you > > > have received this communication in error, please notify the sender > > > immediately by replying "Received in error" and immediately delete this > > > message and all its attachments. > > > > > ------------------------------------------------------------------------------------------------------------------------------------- > > > > Were you using the same machine with hyperterm? > > Use dmesg and setserial to check the if your serial is initialized, > > enabled and set up properly. There is no magic really with minicom if > > your hardware is working and setup properly. > > Vivek has nice simple tutorial, you probably know that one already. > > > > http://www.cyberciti.biz/tips/connect-soekris-single-board-computer-using-minicom.html > > Run minicom with -s and select Filenames and paths, then F - Logging > > options and make sure you can see minicom.log and B,C=yes. > > Then save a dfl and exit once still connected to the switch. > > You should see: > > > > Welcome to minicom > > 2.5 > > OPTIONS: > > I18n > > Compiled on Feb 24 2011, > > 11:25:53. > > Port /dev/ttyS0 > > Press CTRL-A Z for help on special keys > > > > Now press Ctrl-A L to capture the session to the file and then press > > Ctrl-A F to send a break. See if you will be able to connect. If not, in > > you ~ should be a minicom capture log, try to see if there is anything > > in it. > > > > Regards, > > Ges > > > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > -- > ------------------------------------------------------------------------------------------------------------------------------------- > NOTICE: This message, including all attachments, is intended for the use of > the individual or entity to which it is addressed and may contain > information that is privileged, confidential and exempt from disclosure > under applicable law. If the reader of this message is not the intended > recipient, or the employee or agent responsible for delivering this message > to its intended recipient, you are hereby notified that any dissemination, > distribution or copying of this communication is strictly prohibited. If you > have received this communication in error, please notify the sender > immediately by replying "Received in error" and immediately delete this > message and all its attachments. > ------------------------------------------------------------------------------------------------------------------------------------- No, there should be no difference, as you would be using the "same" device /dev/ttyS0 (COM1) or /dev/ttyS1 (COM2) for example. The difference though may be in settings of the interface. You should check in the hardware manual of your system for serial interface settings. Regards, Ges -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
