>>>>> "Peter" == Peter Sanders <plsander@xxxxxxxxx> writes:
Peter> have a RAID 6 array, 6 devices. Been running it for years without much issue.
Peter> Had hardware issues with my system - ended up replacing the
Peter> motherboard, video card, and power supply and re-installing the OS
Peter> (Debian 11).
Can you give us details on the old vs new motherboard/cpu? It might
be that you need to tweak the BIOS of the motherboard to expose the
old SATA formats as well.
Did you install debian onto a fresh boot disk? Is your BIOS setup to
only do the new form of booting from UEFI devices, so maybe check your
BIOS settings that the data drives are all in AHCI mode, or possibly
even in IDE mode. It all depends on how old the original hardware
was.
I just recenly upgraded from a 2010 MB/CPU combo and I had to tweak
the BIOS defaults to see my disks. I guess I should do a clean
install from a blank disk, but I wanted to minimize downtime.
Wols has some great advice here, and I heartily recommend that you use
overlayfs when doing your testing. Check the RAID WIKI for
suggestions.
And don't panic! Your data is probably there, but just missing the
super blocks or partition tables.
John
Peter> As the hardware issues evolved, I'd crash, reboot, un-mount the array,
Peter> run fsck, mount and continue on my way - no problems.
Peter> After the hardware was replaced, my array will not assemble - mdadm
Peter> assemble reports no RAID superblock on the devices.
Peter> root@superior:/etc/mdadm# mdadm --assemble --scan --verbose
Peter> mdadm: looking for devices for /dev/md/0
Peter> mdadm: cannot open device /dev/sr0: No medium found
Peter> mdadm: No super block found on /dev/sda (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sda
Peter> mdadm: No super block found on /dev/sdb (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sdb
Peter> Examine reports
Peter> /dev/sda:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> Searching for these results indicate I can rebuild the superblock, but
Peter> details on how to do that are lacking, at least on the pages I found.
Peter> Currently I have no /dev/md* devices.
Peter> I have access to the old mdadm.conf file - have tried assembling with
Peter> it, with the default mdadm.conf, and with no mdadm.conf file in /etc
Peter> and /etc/mdadm.
Peter> Suggestions for how to get the array back would be most appreciated.
Peter> Thanks
Peter> - Peter
Peter> Here is the data suggested from the wiki page:
Peter> root@superior:/etc/mdadm# mdadm --assemble --scan --verbose
Peter> mdadm: looking for devices for /dev/md/0
Peter> mdadm: cannot open device /dev/sr0: No medium found
Peter> mdadm: No super block found on /dev/sda (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sda
Peter> mdadm: No super block found on /dev/sdb (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sdb
Peter> mdadm: No super block found on /dev/sdd (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sdd
Peter> mdadm: No super block found on /dev/sde (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sde
Peter> mdadm: No super block found on /dev/sdf (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sdf
Peter> mdadm: No super block found on /dev/sdc (Expected magic a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/sdc
Peter> mdadm: No super block found on /dev/nvme0n1p9 (Expected magic
Peter> a92b4efc, got 00000000)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p9
Peter> mdadm: No super block found on /dev/nvme0n1p8 (Expected magic
Peter> a92b4efc, got 0000040c)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p8
Peter> mdadm: No super block found on /dev/nvme0n1p7 (Expected magic
Peter> a92b4efc, got 00002004)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p7
Peter> mdadm: No super block found on /dev/nvme0n1p6 (Expected magic
Peter> a92b4efc, got 0000040d)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p6
Peter> mdadm: No super block found on /dev/nvme0n1p5 (Expected magic
Peter> a92b4efc, got 00000409)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p5
Peter> mdadm: /dev/nvme0n1p2 is too small for md: size is 2 sectors.
Peter> mdadm: no RAID superblock on /dev/nvme0n1p2
Peter> mdadm: No super block found on /dev/nvme0n1p1 (Expected magic
Peter> a92b4efc, got 00040001)
Peter> mdadm: no RAID superblock on /dev/nvme0n1p1
Peter> mdadm: No super block found on /dev/nvme0n1 (Expected magic a92b4efc,
Peter> got 7a78e8ed)
Peter> mdadm: no RAID superblock on /dev/nvme0n1
Peter> root@superior:/etc/mdadm#
Peter> uname -a
Peter> Linux superior 5.10.0-17-amd64 #1 SMP Debian 5.10.136-1 (2022-08-13)
Peter> x86_64 GNU/Linux
Peter> mdadm --version
Peter> mdadm - v4.1 - 2018-10-01
Peter> smartctl devices ------------
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Toshiba P300
Peter> Device Model: TOSHIBA HDWD130
Peter> Serial Number: 477ALBNAS
Peter> LU WWN Device Id: 5 000039 fe6d2e832
Peter> Firmware Version: MX6OACF0
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Rotation Rate: 7200 rpm
Peter> Form Factor: 3.5 inches
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ATA8-ACS T13/1699-D revision 4
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:49 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Disabled
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x80) Offline data collection activity
Peter> was never started.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (21791) seconds.
Peter> Offline data collection
Peter> capabilities: (0x5b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> No Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 1) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 364) minutes.
Peter> SCT capabilities: (0x003d) SCT Status supported.
Peter> SCT Error Recovery Control supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
Peter> 2 Throughput_Performance P-S--- 141 141 054 - 66
Peter> 3 Spin_Up_Time POS--- 160 160 024 - 361 (Average 357)
Peter> 4 Start_Stop_Count -O--C- 100 100 000 - 204
Peter> 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
Peter> 7 Seek_Error_Rate PO-R-- 100 100 067 - 0
Peter> 8 Seek_Time_Performance P-S--- 124 124 020 - 33
Peter> 9 Power_On_Hours -O--C- 095 095 000 - 41740
Peter> 10 Spin_Retry_Count PO--C- 100 100 060 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 204
Peter> 192 Power-Off_Retract_Count -O--CK 100 100 000 - 759
Peter> 193 Load_Cycle_Count -O--C- 100 100 000 - 759
Peter> 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 20/50)
Peter> 196 Reallocated_Event_Count -O--CK 100 100 000 - 0
Peter> 197 Current_Pending_Sector -O---K 100 100 000 - 0
Peter> 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x03 GPL R/O 1 Ext. Comprehensive SMART error log
Peter> 0x04 GPL R/O 7 Device Statistics log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x08 GPL R/O 2 Power Conditions log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x20 GPL R/O 1 Streaming performance log [OBS-8]
Peter> 0x21 GPL R/O 1 Write stream error log
Peter> 0x22 GPL R/O 1 Read stream error log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> No self-tests have been logged. [To run self-tests, use: smartctl -t]
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 256 (0x0100)
Peter> Device State: Active (0)
Peter> Current Temperature: 33 Celsius
Peter> Power Cycle Min/Max Temperature: 29/33 Celsius
Peter> Lifetime Min/Max Temperature: 20/50 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -40/70 Celsius
Peter> Temperature History Size (Index): 128 (51)
Peter> Index Estimated Time Temperature Celsius
Peter> 52 2022-08-25 19:12 33 **************
Peter> ... ..( 76 skipped). .. **************
Peter> 1 2022-08-25 20:29 33 **************
Peter> 2 2022-08-25 20:30 ? -
Peter> 3 2022-08-25 20:31 33 **************
Peter> 4 2022-08-25 20:32 34 ***************
Peter> 5 2022-08-25 20:33 33 **************
Peter> 6 2022-08-25 20:34 34 ***************
Peter> ... ..( 2 skipped). .. ***************
Peter> 9 2022-08-25 20:37 34 ***************
Peter> 10 2022-08-25 20:38 ? -
Peter> 11 2022-08-25 20:39 29 **********
Peter> 12 2022-08-25 20:40 30 ***********
Peter> ... ..( 2 skipped). .. ***********
Peter> 15 2022-08-25 20:43 30 ***********
Peter> 16 2022-08-25 20:44 31 ************
Peter> ... ..( 3 skipped). .. ************
Peter> 20 2022-08-25 20:48 31 ************
Peter> 21 2022-08-25 20:49 32 *************
Peter> ... ..( 9 skipped). .. *************
Peter> 31 2022-08-25 20:59 32 *************
Peter> 32 2022-08-25 21:00 33 **************
Peter> ... ..( 18 skipped). .. **************
Peter> 51 2022-08-25 21:19 33 **************
Peter> SCT Error Recovery Control:
Peter> Read: Disabled
Peter> Write: Disabled
Peter> Device Statistics (GP Log 0x04)
Peter> Page Offset Size Value Flags Description
Peter> 0x01 ===== = = === == General Statistics (rev 1) ==
Peter> 0x01 0x008 4 204 --- Lifetime Power-On Resets
Peter> 0x01 0x010 4 41740 --- Power-on Hours
Peter> 0x01 0x018 6 20304278904 --- Logical Sectors Written
Peter> 0x01 0x020 6 64656942 --- Number of Write Commands
Peter> 0x01 0x028 6 350269182084 --- Logical Sectors Read
Peter> 0x01 0x030 6 481405773 --- Number of Read Commands
Peter> 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
Peter> 0x03 0x008 4 41734 --- Spindle Motor Power-on Hours
Peter> 0x03 0x010 4 41734 --- Head Flying Hours
Peter> 0x03 0x018 4 759 --- Head Load Events
Peter> 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
Peter> 0x03 0x028 4 22 --- Read Recovery Attempts
Peter> 0x03 0x030 4 6 --- Number of Mechanical Start Failures
Peter> 0x04 ===== = = === == General Errors Statistics (rev 1) ==
Peter> 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
Peter> 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and
Peter> Completion
Peter> 0x05 ===== = = === == Temperature Statistics (rev 1) ==
Peter> 0x05 0x008 1 33 --- Current Temperature
Peter> 0x05 0x010 1 33 N-- Average Short Term Temperature
Peter> 0x05 0x018 1 37 N-- Average Long Term Temperature
Peter> 0x05 0x020 1 50 --- Highest Temperature
Peter> 0x05 0x028 1 20 --- Lowest Temperature
Peter> 0x05 0x030 1 46 N-- Highest Average Short Term Temperature
Peter> 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
Peter> 0x05 0x040 1 43 N-- Highest Average Long Term Temperature
Peter> 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
Peter> 0x05 0x050 4 0 --- Time in Over-Temperature
Peter> 0x05 0x058 1 60 --- Specified Maximum Operating Temperature
Peter> 0x05 0x060 4 0 --- Time in Under-Temperature
Peter> 0x05 0x068 1 0 --- Specified Minimum Operating Temperature
Peter> 0x06 ===== = = === == Transport Statistics (rev 1) ==
Peter> 0x06 0x008 4 1006 --- Number of Hardware Resets
Peter> 0x06 0x010 4 494 --- Number of ASR Events
Peter> 0x06 0x018 4 0 --- Number of Interface CRC Errors
Peter> |||_ C monitored condition met
Peter> ||__ D supports DSN
Peter> |___ N normalized value
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x0009 2 35 Transition from drive PhyRdy to drive PhyNRdy
Peter> 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x000d 2 0 Non-CRC errors within host-to-device FIS
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Western Digital Green
Peter> Device Model: WDC WD30EZRX-00DC0B0
Peter> Serial Number: WD-WCC1T0668790
Peter> LU WWN Device Id: 5 0014ee 2084d406a
Peter> Firmware Version: 80.00A80
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ACS-2 (minor revision not indicated)
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:51 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Unavailable
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x82) Offline data collection activity
Peter> was completed without error.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (40560) seconds.
Peter> Offline data collection
Peter> capabilities: (0x7b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 2) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 407) minutes.
Peter> Conveyance self-test routine
Peter> recommended polling time: ( 5) minutes.
Peter> SCT capabilities: (0x70b5) SCT Status supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
Peter> 3 Spin_Up_Time POS--K 181 178 021 - 5916
Peter> 4 Start_Stop_Count -O--CK 100 100 000 - 377
Peter> 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
Peter> 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
Peter> 9 Power_On_Hours -O--CK 007 007 000 - 68295
Peter> 10 Spin_Retry_Count -O--CK 100 100 000 - 0
Peter> 11 Calibration_Retry_Count -O--CK 100 100 000 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 296
Peter> 192 Power-Off_Retract_Count -O--CK 200 200 000 - 242
Peter> 193 Load_Cycle_Count -O--CK 052 052 000 - 445057
Peter> 194 Temperature_Celsius -O---K 121 102 000 - 29
Peter> 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
Peter> 197 Current_Pending_Sector -O--CK 200 200 000 - 0
Peter> 198 Offline_Uncorrectable ----CK 200 200 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
Peter> 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x02 SL R/O 5 Comprehensive SMART error log
Peter> 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
Peter> 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
Peter> 0xbd GPL,SL VS 1 Device vendor specific log
Peter> 0xc0 GPL,SL VS 1 Device vendor specific log
Peter> 0xc1 GPL VS 93 Device vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> Num Test_Description Status Remaining
Peter> LifeTime(hours) LBA_of_first_error
Peter> # 1 Extended offline Completed without error 00% 7 -
Peter> # 2 Short offline Completed without error 00% 0 -
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 258 (0x0102)
Peter> Device State: Active (0)
Peter> Current Temperature: 29 Celsius
Peter> Power Cycle Min/Max Temperature: 28/29 Celsius
Peter> Lifetime Min/Max Temperature: 2/48 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> Vendor specific:
Peter> 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Peter> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -41/85 Celsius
Peter> Temperature History Size (Index): 478 (138)
Peter> Index Estimated Time Temperature Celsius
Peter> 139 2022-08-25 13:22 30 ***********
Peter> 140 2022-08-25 13:23 29 **********
Peter> ... ..( 5 skipped). .. **********
Peter> 146 2022-08-25 13:29 29 **********
Peter> 147 2022-08-25 13:30 ? -
Peter> 148 2022-08-25 13:31 26 *******
Peter> 149 2022-08-25 13:32 ? -
Peter> 150 2022-08-25 13:33 28 *********
Peter> 151 2022-08-25 13:34 ? -
Peter> 152 2022-08-25 13:35 28 *********
Peter> 153 2022-08-25 13:36 28 *********
Peter> 154 2022-08-25 13:37 29 **********
Peter> ... ..( 55 skipped). .. **********
Peter> 210 2022-08-25 14:33 29 **********
Peter> 211 2022-08-25 14:34 30 ***********
Peter> ... ..( 11 skipped). .. ***********
Peter> 223 2022-08-25 14:46 30 ***********
Peter> 224 2022-08-25 14:47 29 **********
Peter> ... ..(103 skipped). .. **********
Peter> 328 2022-08-25 16:31 29 **********
Peter> 329 2022-08-25 16:32 30 ***********
Peter> ... ..( 18 skipped). .. ***********
Peter> 348 2022-08-25 16:51 30 ***********
Peter> 349 2022-08-25 16:52 29 **********
Peter> ... ..( 33 skipped). .. **********
Peter> 383 2022-08-25 17:26 29 **********
Peter> 384 2022-08-25 17:27 30 ***********
Peter> ... ..( 10 skipped). .. ***********
Peter> 395 2022-08-25 17:38 30 ***********
Peter> 396 2022-08-25 17:39 29 **********
Peter> ... ..(218 skipped). .. **********
Peter> 137 2022-08-25 21:18 29 **********
Peter> 138 2022-08-25 21:19 ? -
Peter> SCT Error Recovery Control command not supported
Peter> Device Statistics (GP/SMART Log 0x04) not supported
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x0008 2 0 Device-to-host non-data FIS retries
Peter> 0x0009 2 305 Transition from drive PhyRdy to drive PhyNRdy
Peter> 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
Peter> 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
Peter> 0x8000 4 2491 Vendor specific
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Toshiba P300
Peter> Device Model: TOSHIBA HDWD130
Peter> Serial Number: Y7211KPAS
Peter> LU WWN Device Id: 5 000039 fe6dca946
Peter> Firmware Version: MX6OACF0
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Rotation Rate: 7200 rpm
Peter> Form Factor: 3.5 inches
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ATA8-ACS T13/1699-D revision 4
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:51 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Disabled
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x80) Offline data collection activity
Peter> was never started.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (21791) seconds.
Peter> Offline data collection
Peter> capabilities: (0x5b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> No Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 1) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 364) minutes.
Peter> SCT capabilities: (0x003d) SCT Status supported.
Peter> SCT Error Recovery Control supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
Peter> 2 Throughput_Performance P-S--- 139 139 054 - 71
Peter> 3 Spin_Up_Time POS--- 160 160 024 - 361 (Average 355)
Peter> 4 Start_Stop_Count -O--C- 100 100 000 - 189
Peter> 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
Peter> 7 Seek_Error_Rate PO-R-- 100 100 067 - 0
Peter> 8 Seek_Time_Performance P-S--- 128 128 020 - 31
Peter> 9 Power_On_Hours -O--C- 095 095 000 - 35428
Peter> 10 Spin_Retry_Count PO--C- 100 100 060 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 189
Peter> 192 Power-Off_Retract_Count -O--CK 100 100 000 - 599
Peter> 193 Load_Cycle_Count -O--C- 100 100 000 - 599
Peter> 194 Temperature_Celsius -O---- 176 176 000 - 34 (Min/Max 19/50)
Peter> 196 Reallocated_Event_Count -O--CK 100 100 000 - 0
Peter> 197 Current_Pending_Sector -O---K 100 100 000 - 0
Peter> 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x03 GPL R/O 1 Ext. Comprehensive SMART error log
Peter> 0x04 GPL R/O 7 Device Statistics log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x08 GPL R/O 2 Power Conditions log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x20 GPL R/O 1 Streaming performance log [OBS-8]
Peter> 0x21 GPL R/O 1 Write stream error log
Peter> 0x22 GPL R/O 1 Read stream error log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> No self-tests have been logged. [To run self-tests, use: smartctl -t]
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 256 (0x0100)
Peter> Device State: Active (0)
Peter> Current Temperature: 34 Celsius
Peter> Power Cycle Min/Max Temperature: 28/34 Celsius
Peter> Lifetime Min/Max Temperature: 19/50 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -40/70 Celsius
Peter> Temperature History Size (Index): 128 (15)
Peter> Index Estimated Time Temperature Celsius
Peter> 16 2022-08-25 19:12 33 **************
Peter> ... ..( 66 skipped). .. **************
Peter> 83 2022-08-25 20:19 33 **************
Peter> 84 2022-08-25 20:20 34 ***************
Peter> ... ..( 8 skipped). .. ***************
Peter> 93 2022-08-25 20:29 34 ***************
Peter> 94 2022-08-25 20:30 ? -
Peter> 95 2022-08-25 20:31 34 ***************
Peter> ... ..( 5 skipped). .. ***************
Peter> 101 2022-08-25 20:37 34 ***************
Peter> 102 2022-08-25 20:38 ? -
Peter> 103 2022-08-25 20:39 29 **********
Peter> 104 2022-08-25 20:40 29 **********
Peter> 105 2022-08-25 20:41 30 ***********
Peter> 106 2022-08-25 20:42 30 ***********
Peter> 107 2022-08-25 20:43 31 ************
Peter> ... ..( 3 skipped). .. ************
Peter> 111 2022-08-25 20:47 31 ************
Peter> 112 2022-08-25 20:48 32 *************
Peter> ... ..( 4 skipped). .. *************
Peter> 117 2022-08-25 20:53 32 *************
Peter> 118 2022-08-25 20:54 33 **************
Peter> ... ..( 15 skipped). .. **************
Peter> 6 2022-08-25 21:10 33 **************
Peter> 7 2022-08-25 21:11 34 ***************
Peter> 8 2022-08-25 21:12 33 **************
Peter> 9 2022-08-25 21:13 34 ***************
Peter> ... ..( 5 skipped). .. ***************
Peter> 15 2022-08-25 21:19 34 ***************
Peter> SCT Error Recovery Control:
Peter> Read: Disabled
Peter> Write: Disabled
Peter> Device Statistics (GP Log 0x04)
Peter> Page Offset Size Value Flags Description
Peter> 0x01 ===== = = === == General Statistics (rev 1) ==
Peter> 0x01 0x008 4 189 --- Lifetime Power-On Resets
Peter> 0x01 0x010 4 35428 --- Power-on Hours
Peter> 0x01 0x018 6 12728825059 --- Logical Sectors Written
Peter> 0x01 0x020 6 36220308 --- Number of Write Commands
Peter> 0x01 0x028 6 289884223915 --- Logical Sectors Read
Peter> 0x01 0x030 6 321688917 --- Number of Read Commands
Peter> 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
Peter> 0x03 0x008 4 35423 --- Spindle Motor Power-on Hours
Peter> 0x03 0x010 4 35423 --- Head Flying Hours
Peter> 0x03 0x018 4 599 --- Head Load Events
Peter> 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
Peter> 0x03 0x028 4 7 --- Read Recovery Attempts
Peter> 0x03 0x030 4 6 --- Number of Mechanical Start Failures
Peter> 0x04 ===== = = === == General Errors Statistics (rev 1) ==
Peter> 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
Peter> 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and
Peter> Completion
Peter> 0x05 ===== = = === == Temperature Statistics (rev 1) ==
Peter> 0x05 0x008 1 34 --- Current Temperature
Peter> 0x05 0x010 1 34 N-- Average Short Term Temperature
Peter> 0x05 0x018 1 37 N-- Average Long Term Temperature
Peter> 0x05 0x020 1 50 --- Highest Temperature
Peter> 0x05 0x028 1 19 --- Lowest Temperature
Peter> 0x05 0x030 1 46 N-- Highest Average Short Term Temperature
Peter> 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
Peter> 0x05 0x040 1 43 N-- Highest Average Long Term Temperature
Peter> 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
Peter> 0x05 0x050 4 0 --- Time in Over-Temperature
Peter> 0x05 0x058 1 60 --- Specified Maximum Operating Temperature
Peter> 0x05 0x060 4 0 --- Time in Under-Temperature
Peter> 0x05 0x068 1 0 --- Specified Minimum Operating Temperature
Peter> 0x06 ===== = = === == Transport Statistics (rev 1) ==
Peter> 0x06 0x008 4 147297 --- Number of Hardware Resets
Peter> 0x06 0x010 4 8793 --- Number of ASR Events
Peter> 0x06 0x018 4 0 --- Number of Interface CRC Errors
Peter> |||_ C monitored condition met
Peter> ||__ D supports DSN
Peter> |___ N normalized value
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x0009 2 29 Transition from drive PhyRdy to drive PhyNRdy
Peter> 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x000d 2 0 Non-CRC errors within host-to-device FIS
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Western Digital Green
Peter> Device Model: WDC WD30EZRX-00D8PB0
Peter> Serial Number: WD-WCC4N0091255
Peter> LU WWN Device Id: 5 0014ee 2b3d4ffa1
Peter> Firmware Version: 80.00A80
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Rotation Rate: 5400 rpm
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ACS-2 (minor revision not indicated)
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:53 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Unavailable
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x82) Offline data collection activity
Peter> was completed without error.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (42480) seconds.
Peter> Offline data collection
Peter> capabilities: (0x7b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 2) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 426) minutes.
Peter> Conveyance self-test routine
Peter> recommended polling time: ( 5) minutes.
Peter> SCT capabilities: (0x7035) SCT Status supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 2
Peter> 3 Spin_Up_Time POS--K 184 181 021 - 5783
Peter> 4 Start_Stop_Count -O--CK 100 100 000 - 275
Peter> 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
Peter> 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
Peter> 9 Power_On_Hours -O--CK 039 039 000 - 44593
Peter> 10 Spin_Retry_Count -O--CK 100 100 000 - 0
Peter> 11 Calibration_Retry_Count -O--CK 100 100 000 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 273
Peter> 192 Power-Off_Retract_Count -O--CK 200 200 000 - 225
Peter> 193 Load_Cycle_Count -O--CK 047 047 000 - 461100
Peter> 194 Temperature_Celsius -O---K 122 105 000 - 28
Peter> 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
Peter> 197 Current_Pending_Sector -O--CK 200 200 000 - 0
Peter> 198 Offline_Uncorrectable ----CK 200 200 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
Peter> 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x02 SL R/O 5 Comprehensive SMART error log
Peter> 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
Peter> 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
Peter> 0xbd GPL,SL VS 1 Device vendor specific log
Peter> 0xc0 GPL,SL VS 1 Device vendor specific log
Peter> 0xc1 GPL VS 93 Device vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> No self-tests have been logged. [To run self-tests, use: smartctl -t]
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 258 (0x0102)
Peter> Device State: Active (0)
Peter> Current Temperature: 28 Celsius
Peter> Power Cycle Min/Max Temperature: 27/28 Celsius
Peter> Lifetime Min/Max Temperature: 2/44 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> Vendor specific:
Peter> 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Peter> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -41/85 Celsius
Peter> Temperature History Size (Index): 478 (444)
Peter> Index Estimated Time Temperature Celsius
Peter> 445 2022-08-25 13:22 29 **********
Peter> ... ..( 33 skipped). .. **********
Peter> 1 2022-08-25 13:56 29 **********
Peter> 2 2022-08-25 13:57 ? -
Peter> 3 2022-08-25 13:58 29 **********
Peter> ... ..( 6 skipped). .. **********
Peter> 10 2022-08-25 14:05 29 **********
Peter> 11 2022-08-25 14:06 ? -
Peter> 12 2022-08-25 14:07 26 *******
Peter> 13 2022-08-25 14:08 ? -
Peter> 14 2022-08-25 14:09 27 ********
Peter> 15 2022-08-25 14:10 27 ********
Peter> 16 2022-08-25 14:11 28 *********
Peter> ... ..( 37 skipped). .. *********
Peter> 54 2022-08-25 14:49 28 *********
Peter> 55 2022-08-25 14:50 29 **********
Peter> ... ..(388 skipped). .. **********
Peter> 444 2022-08-25 21:19 29 **********
Peter> SCT Error Recovery Control command not supported
Peter> Device Statistics (GP/SMART Log 0x04) not supported
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x0008 2 0 Device-to-host non-data FIS retries
Peter> 0x0009 2 286 Transition from drive PhyRdy to drive PhyNRdy
Peter> 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
Peter> 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
Peter> 0x8000 4 2493 Vendor specific
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Western Digital Green
Peter> Device Model: WDC WD30EZRX-00MMMB0
Peter> Serial Number: WD-WCAWZ2669166
Peter> LU WWN Device Id: 5 0014ee 15a13d994
Peter> Firmware Version: 80.00A80
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ATA8-ACS (minor revision not indicated)
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:53 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Unavailable
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x82) Offline data collection activity
Peter> was completed without error.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (50160) seconds.
Peter> Offline data collection
Peter> capabilities: (0x7b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 2) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 482) minutes.
Peter> Conveyance self-test routine
Peter> recommended polling time: ( 5) minutes.
Peter> SCT capabilities: (0x3035) SCT Status supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
Peter> 3 Spin_Up_Time POS--K 153 138 021 - 9350
Peter> 4 Start_Stop_Count -O--CK 100 100 000 - 297
Peter> 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
Peter> 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
Peter> 9 Power_On_Hours -O--CK 040 040 000 - 44409
Peter> 10 Spin_Retry_Count -O--CK 100 100 000 - 0
Peter> 11 Calibration_Retry_Count -O--CK 100 100 000 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 268
Peter> 192 Power-Off_Retract_Count -O--CK 200 200 000 - 218
Peter> 193 Load_Cycle_Count -O--CK 001 001 000 - 1082082
Peter> 194 Temperature_Celsius -O---K 122 105 000 - 30
Peter> 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
Peter> 197 Current_Pending_Sector -O--CK 200 200 000 - 0
Peter> 198 Offline_Uncorrectable ----CK 200 200 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
Peter> 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x02 SL R/O 5 Comprehensive SMART error log
Peter> 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
Peter> 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
Peter> 0xbd GPL,SL VS 1 Device vendor specific log
Peter> 0xc0 GPL,SL VS 1 Device vendor specific log
Peter> 0xc1 GPL VS 93 Device vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> No self-tests have been logged. [To run self-tests, use: smartctl -t]
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 258 (0x0102)
Peter> Device State: Active (0)
Peter> Current Temperature: 30 Celsius
Peter> Power Cycle Min/Max Temperature: 27/30 Celsius
Peter> Lifetime Min/Max Temperature: 0/47 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -41/85 Celsius
Peter> Temperature History Size (Index): 478 (88)
Peter> Index Estimated Time Temperature Celsius
Peter> 89 2022-08-25 13:22 30 ***********
Peter> ... ..( 33 skipped). .. ***********
Peter> 123 2022-08-25 13:56 30 ***********
Peter> 124 2022-08-25 13:57 ? -
Peter> 125 2022-08-25 13:58 31 ************
Peter> 126 2022-08-25 13:59 30 ***********
Peter> ... ..( 5 skipped). .. ***********
Peter> 132 2022-08-25 14:05 30 ***********
Peter> 133 2022-08-25 14:06 ? -
Peter> 134 2022-08-25 14:07 26 *******
Peter> 135 2022-08-25 14:08 ? -
Peter> 136 2022-08-25 14:09 27 ********
Peter> ... ..( 3 skipped). .. ********
Peter> 140 2022-08-25 14:13 27 ********
Peter> 141 2022-08-25 14:14 28 *********
Peter> ... ..( 3 skipped). .. *********
Peter> 145 2022-08-25 14:18 28 *********
Peter> 146 2022-08-25 14:19 29 **********
Peter> ... ..( 13 skipped). .. **********
Peter> 160 2022-08-25 14:33 29 **********
Peter> 161 2022-08-25 14:34 30 ***********
Peter> ... ..( 43 skipped). .. ***********
Peter> 205 2022-08-25 15:18 30 ***********
Peter> 206 2022-08-25 15:19 31 ************
Peter> 207 2022-08-25 15:20 30 ***********
Peter> ... ..(168 skipped). .. ***********
Peter> 376 2022-08-25 18:09 30 ***********
Peter> 377 2022-08-25 18:10 31 ************
Peter> 378 2022-08-25 18:11 30 ***********
Peter> ... ..( 34 skipped). .. ***********
Peter> 413 2022-08-25 18:46 30 ***********
Peter> 414 2022-08-25 18:47 31 ************
Peter> 415 2022-08-25 18:48 30 ***********
Peter> ... ..( 7 skipped). .. ***********
Peter> 423 2022-08-25 18:56 30 ***********
Peter> 424 2022-08-25 18:57 31 ************
Peter> 425 2022-08-25 18:58 30 ***********
Peter> ... ..( 7 skipped). .. ***********
Peter> 433 2022-08-25 19:06 30 ***********
Peter> 434 2022-08-25 19:07 31 ************
Peter> 435 2022-08-25 19:08 30 ***********
Peter> ... ..( 47 skipped). .. ***********
Peter> 5 2022-08-25 19:56 30 ***********
Peter> 6 2022-08-25 19:57 31 ************
Peter> 7 2022-08-25 19:58 30 ***********
Peter> ... ..( 80 skipped). .. ***********
Peter> 88 2022-08-25 21:19 30 ***********
Peter> SCT Error Recovery Control command not supported
Peter> Device Statistics (GP/SMART Log 0x04) not supported
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x8000 4 2492 Vendor specific
Peter> smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-17-amd64] (local build)
Peter> Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Peter> === START OF INFORMATION SECTION ===
Peter> Model Family: Toshiba P300
Peter> Device Model: TOSHIBA HDWD130
Peter> Serial Number: 477ABEJAS
Peter> LU WWN Device Id: 5 000039 fe6d2ce25
Peter> Firmware Version: MX6OACF0
Peter> User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Peter> Sector Sizes: 512 bytes logical, 4096 bytes physical
Peter> Rotation Rate: 7200 rpm
Peter> Form Factor: 3.5 inches
Peter> Device is: In smartctl database [for details use: -P show]
Peter> ATA Version is: ATA8-ACS T13/1699-D revision 4
Peter> SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Peter> Local Time is: Thu Aug 25 21:19:53 2022 EDT
Peter> SMART support is: Available - device has SMART capability.
Peter> SMART support is: Enabled
Peter> AAM feature is: Unavailable
Peter> APM feature is: Disabled
Peter> Rd look-ahead is: Enabled
Peter> Write cache is: Enabled
Peter> DSN feature is: Unavailable
Peter> ATA Security is: Disabled, frozen [SEC2]
Peter> Wt Cache Reorder: Enabled
Peter> === START OF READ SMART DATA SECTION ===
Peter> SMART overall-health self-assessment test result: PASSED
Peter> General SMART Values:
Peter> Offline data collection status: (0x80) Offline data collection activity
Peter> was never started.
Peter> Auto Offline Data Collection: Enabled.
Peter> Self-test execution status: ( 0) The previous self-test
Peter> routine completed
Peter> without error or no self-test has ever
Peter> been run.
Peter> Total time to complete Offline
Peter> data collection: (23082) seconds.
Peter> Offline data collection
Peter> capabilities: (0x5b) SMART execute Offline immediate.
Peter> Auto Offline data collection on/off support.
Peter> Suspend Offline collection upon new
Peter> command.
Peter> Offline surface scan supported.
Peter> Self-test supported.
Peter> No Conveyance Self-test supported.
Peter> Selective Self-test supported.
Peter> SMART capabilities: (0x0003) Saves SMART data before entering
Peter> power-saving mode.
Peter> Supports SMART auto save timer.
Peter> Error logging capability: (0x01) Error logging supported.
Peter> General Purpose Logging supported.
Peter> Short self-test routine
Peter> recommended polling time: ( 1) minutes.
Peter> Extended self-test routine
Peter> recommended polling time: ( 385) minutes.
Peter> SCT capabilities: (0x003d) SCT Status supported.
Peter> SCT Error Recovery Control supported.
Peter> SCT Feature Control supported.
Peter> SCT Data Table supported.
Peter> SMART Attributes Data Structure revision number: 16
Peter> Vendor Specific SMART Attributes with Thresholds:
Peter> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
Peter> 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
Peter> 2 Throughput_Performance P-S--- 140 140 054 - 68
Peter> 3 Spin_Up_Time POS--- 161 161 024 - 358 (Average 354)
Peter> 4 Start_Stop_Count -O--C- 100 100 000 - 243
Peter> 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
Peter> 7 Seek_Error_Rate PO-R-- 100 100 067 - 0
Peter> 8 Seek_Time_Performance P-S--- 126 126 020 - 32
Peter> 9 Power_On_Hours -O--C- 094 094 000 - 44046
Peter> 10 Spin_Retry_Count PO--C- 100 100 060 - 0
Peter> 12 Power_Cycle_Count -O--CK 100 100 000 - 243
Peter> 192 Power-Off_Retract_Count -O--CK 100 100 000 - 912
Peter> 193 Load_Cycle_Count -O--C- 100 100 000 - 912
Peter> 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 19/46)
Peter> 196 Reallocated_Event_Count -O--CK 100 100 000 - 0
Peter> 197 Current_Pending_Sector -O---K 100 100 000 - 0
Peter> 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
Peter> 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
Peter> ||||||_ K auto-keep
Peter> |||||__ C event count
Peter> ||||___ R error rate
Peter> |||____ S speed/performance
Peter> ||_____ O updated online
Peter> |______ P prefailure warning
Peter> General Purpose Log Directory Version 1
Peter> SMART Log Directory Version 1 [multi-sector log support]
Peter> Address Access R/W Size Description
Peter> 0x00 GPL,SL R/O 1 Log Directory
Peter> 0x01 SL R/O 1 Summary SMART error log
Peter> 0x03 GPL R/O 1 Ext. Comprehensive SMART error log
Peter> 0x04 GPL R/O 7 Device Statistics log
Peter> 0x06 SL R/O 1 SMART self-test log
Peter> 0x07 GPL R/O 1 Extended self-test log
Peter> 0x08 GPL R/O 2 Power Conditions log
Peter> 0x09 SL R/W 1 Selective self-test log
Peter> 0x10 GPL R/O 1 NCQ Command Error log
Peter> 0x11 GPL R/O 1 SATA Phy Event Counters log
Peter> 0x20 GPL R/O 1 Streaming performance log [OBS-8]
Peter> 0x21 GPL R/O 1 Write stream error log
Peter> 0x22 GPL R/O 1 Read stream error log
Peter> 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
Peter> 0xe0 GPL,SL R/W 1 SCT Command/Status
Peter> 0xe1 GPL,SL R/W 1 SCT Data Transfer
Peter> SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Peter> No Errors Logged
Peter> SMART Extended Self-test Log Version: 1 (1 sectors)
Peter> No self-tests have been logged. [To run self-tests, use: smartctl -t]
Peter> SMART Selective self-test log data structure revision number 1
Peter> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
Peter> 1 0 0 Not_testing
Peter> 2 0 0 Not_testing
Peter> 3 0 0 Not_testing
Peter> 4 0 0 Not_testing
Peter> 5 0 0 Not_testing
Peter> Selective self-test flags (0x0):
Peter> After scanning selected spans, do NOT read-scan remainder of disk.
Peter> If Selective self-test is pending on power-up, resume after 0 minute delay.
Peter> SCT Status Version: 3
Peter> SCT Version (vendor specific): 256 (0x0100)
Peter> Device State: Active (0)
Peter> Current Temperature: 31 Celsius
Peter> Power Cycle Min/Max Temperature: 28/32 Celsius
Peter> Lifetime Min/Max Temperature: 19/46 Celsius
Peter> Under/Over Temperature Limit Count: 0/0
Peter> SCT Temperature History Version: 2
Peter> Temperature Sampling Period: 1 minute
Peter> Temperature Logging Interval: 1 minute
Peter> Min/Max recommended Temperature: 0/60 Celsius
Peter> Min/Max Temperature Limit: -40/70 Celsius
Peter> Temperature History Size (Index): 128 (117)
Peter> Index Estimated Time Temperature Celsius
Peter> 118 2022-08-25 19:12 31 ************
Peter> ... ..( 76 skipped). .. ************
Peter> 67 2022-08-25 20:29 31 ************
Peter> 68 2022-08-25 20:30 ? -
Peter> 69 2022-08-25 20:31 31 ************
Peter> 70 2022-08-25 20:32 32 *************
Peter> 71 2022-08-25 20:33 31 ************
Peter> 72 2022-08-25 20:34 31 ************
Peter> 73 2022-08-25 20:35 32 *************
Peter> 74 2022-08-25 20:36 32 *************
Peter> 75 2022-08-25 20:37 32 *************
Peter> 76 2022-08-25 20:38 ? -
Peter> 77 2022-08-25 20:39 28 *********
Peter> 78 2022-08-25 20:40 29 **********
Peter> ... ..( 2 skipped). .. **********
Peter> 81 2022-08-25 20:43 29 **********
Peter> 82 2022-08-25 20:44 30 ***********
Peter> ... ..( 5 skipped). .. ***********
Peter> 88 2022-08-25 20:50 30 ***********
Peter> 89 2022-08-25 20:51 31 ************
Peter> ... ..( 27 skipped). .. ************
Peter> 117 2022-08-25 21:19 31 ************
Peter> SCT Error Recovery Control:
Peter> Read: Disabled
Peter> Write: Disabled
Peter> Device Statistics (GP Log 0x04)
Peter> Page Offset Size Value Flags Description
Peter> 0x01 ===== = = === == General Statistics (rev 1) ==
Peter> 0x01 0x008 4 243 --- Lifetime Power-On Resets
Peter> 0x01 0x010 4 44046 --- Power-on Hours
Peter> 0x01 0x018 6 27756962802 --- Logical Sectors Written
Peter> 0x01 0x020 6 86355955 --- Number of Write Commands
Peter> 0x01 0x028 6 381193626849 --- Logical Sectors Read
Peter> 0x01 0x030 6 791200694 --- Number of Read Commands
Peter> 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
Peter> 0x03 0x008 4 44040 --- Spindle Motor Power-on Hours
Peter> 0x03 0x010 4 44040 --- Head Flying Hours
Peter> 0x03 0x018 4 912 --- Head Load Events
Peter> 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
Peter> 0x03 0x028 4 0 --- Read Recovery Attempts
Peter> 0x03 0x030 4 6 --- Number of Mechanical Start Failures
Peter> 0x04 ===== = = === == General Errors Statistics (rev 1) ==
Peter> 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
Peter> 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and
Peter> Completion
Peter> 0x05 ===== = = === == Temperature Statistics (rev 1) ==
Peter> 0x05 0x008 1 32 --- Current Temperature
Peter> 0x05 0x010 1 31 N-- Average Short Term Temperature
Peter> 0x05 0x018 1 35 N-- Average Long Term Temperature
Peter> 0x05 0x020 1 46 --- Highest Temperature
Peter> 0x05 0x028 1 19 --- Lowest Temperature
Peter> 0x05 0x030 1 43 N-- Highest Average Short Term Temperature
Peter> 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
Peter> 0x05 0x040 1 41 N-- Highest Average Long Term Temperature
Peter> 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
Peter> 0x05 0x050 4 0 --- Time in Over-Temperature
Peter> 0x05 0x058 1 60 --- Specified Maximum Operating Temperature
Peter> 0x05 0x060 4 0 --- Time in Under-Temperature
Peter> 0x05 0x068 1 0 --- Specified Minimum Operating Temperature
Peter> 0x06 ===== = = === == Transport Statistics (rev 1) ==
Peter> 0x06 0x008 4 4706 --- Number of Hardware Resets
Peter> 0x06 0x010 4 3910 --- Number of ASR Events
Peter> 0x06 0x018 4 0 --- Number of Interface CRC Errors
Peter> |||_ C monitored condition met
Peter> ||__ D supports DSN
Peter> |___ N normalized value
Peter> Pending Defects log (GP Log 0x0c) not supported
Peter> SATA Phy Event Counters (GP Log 0x11)
Peter> ID Size Value Description
Peter> 0x0001 2 0 Command failed due to ICRC error
Peter> 0x0002 2 0 R_ERR response for data FIS
Peter> 0x0003 2 0 R_ERR response for device-to-host data FIS
Peter> 0x0004 2 0 R_ERR response for host-to-device data FIS
Peter> 0x0005 2 0 R_ERR response for non-data FIS
Peter> 0x0006 2 0 R_ERR response for device-to-host non-data FIS
Peter> 0x0007 2 0 R_ERR response for host-to-device non-data FIS
Peter> 0x0009 2 29 Transition from drive PhyRdy to drive PhyNRdy
Peter> 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
Peter> 0x000b 2 0 CRC errors within host-to-device FIS
Peter> 0x000d 2 0 Non-CRC errors within host-to-device FIS
Peter> mdadm --examine devices -----
Peter> /dev/sda:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> /dev/sdb:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> /dev/sdc:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> /dev/sdd:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> /dev/sde:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> /dev/sdf:
Peter> MBR Magic : aa55
Peter> Partition[0] : 4294967295 sectors at 1 (type ee)
Peter> mdadm --detail /dev/md0 ------
Peter> lsdrv ------------------------
Peter> PCI [nvme] 01:00.0 Non-Volatile memory controller: Phison Electronics
Peter> Corporation E12 NVMe Controller (rev 01)
Peter> └nvme nvme0 PCIe SSD {21112925606047}
Peter> └nvme0n1 238.47g [259:0] Partitioned (dos)
Peter> ├nvme0n1p1 485.00m [259:1] ext4 {f38776ac-1ce9-4fc8-ba50-94844b9f504e}
Peter> │└Mounted as /dev/nvme0n1p1 @ /boot
Peter> ├nvme0n1p2 1.00k [259:2] Partitioned (dos)
Peter> ├nvme0n1p5 60.54g [259:3] ext4 {5ee1c3c0-3a05-466c-9f98-f5807c8d813b}
Peter> │└Mounted as /dev/nvme0n1p5 @ /
Peter> ├nvme0n1p6 93.13g [259:4] ext4 {9064169f-4fe3-4836-a906-28c1b445cdff}
Peter> │└Mounted as /dev/nvme0n1p6 @ /var
Peter> ├nvme0n1p7 37.00m [259:5] ext4 {25e161ad-94a0-4298-afaf-18e2433766ee}
Peter> ├nvme0n1p8 82.89g [259:6] ext4 {ac874071-d759-4d33-b32f-83272f3eacd9}
Peter> │└Mounted as /dev/nvme0n1p8 @ /home
Peter> └nvme0n1p9 1.41g [259:7] swap {02cef84b-9a9d-4a0a-973c-fda1a78c533c}
Peter> PCI [pata_jmicron] 26:00.1 IDE interface: JMicron Technology Corp.
Peter> JMB368 IDE controller (rev 10)
Peter> └scsi 0:0:0:0 MAD DOG LS-DVDRW TSH652M {MAD_DOG_LS-DVDRW_TSH652M}
Peter> └sr0 1.00g [11:0] Empty/Unknown
Peter> PCI [ahci] 26:00.0 SATA controller: JMicron Technology Corp. JMB363
Peter> SATA/IDE Controller (rev 10)
Peter> └scsi 2:x:x:x [Empty]
Peter> PCI [ahci] 2b:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD]
Peter> FCH SATA Controller [AHCI mode] (rev 51)
Peter> ├scsi 6:0:0:0 ATA TOSHIBA HDWD130 {477ALBNAS}
Peter> │└sda 2.73t [8:0] Partitioned (PMBR)
Peter> └scsi 7:0:0:0 ATA TOSHIBA HDWD130 {Y7211KPAS}
Peter> └sdc 2.73t [8:32] Partitioned (gpt)
Peter> PCI [ahci] 2c:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD]
Peter> FCH SATA Controller [AHCI mode] (rev 51)
Peter> ├scsi 8:0:0:0 ATA WDC WD30EZRX-00D {WD-WCC1T0668790}
Peter> │└sdb 2.73t [8:16] Partitioned (gpt)
Peter> ├scsi 9:0:0:0 ATA WDC WD30EZRX-00D {WD-WCC4N0091255}
Peter> │└sdd 2.73t [8:48] Partitioned (gpt)
Peter> ├scsi 12:0:0:0 ATA WDC WD30EZRX-00M {WD-WCAWZ2669166}
Peter> │└sde 2.73t [8:64] Partitioned (gpt)
Peter> └scsi 13:0:0:0 ATA TOSHIBA HDWD130 {477ABEJAS}
Peter> └sdf 2.73t [8:80] Partitioned (gpt)
Peter> cat /proc/mdstat -------------
Peter> Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
Peter> [raid4] [raid10]
Peter> unused devices: <none>
Peter> cat /etc/mdadm/mdadm.conf ----
Peter> # mdadm.conf
Peter> #
Peter> # !NB! Run update-initramfs -u after updating this file.
Peter> # !NB! This will ensure that initramfs has an uptodate copy.
Peter> #
Peter> # Please refer to mdadm.conf(5) for information about this file.
Peter> #
Peter> # by default (built-in), scan all partitions (/proc/partitions) and all
Peter> # containers for MD superblocks. alternatively, specify devices to scan, using
Peter> # wildcards if desired.
Peter> #DEVICE partitions containers
Peter> # automatically tag new arrays as belonging to the local system
Peter> HOMEHOST <system>
Peter> # instruct the monitoring daemon where to send mail alerts
Peter> MAILADDR root
Peter> # definitions of existing MD arrays
Peter> ARRAY /dev/md/0 metadata=1.2 UUID=109fa7b0:cf08fdba:e36284a9:5786ffff
Peter> name=superior:0
Peter> # This configuration was auto-generated on Sun, 26 Dec 2021 13:31:14
Peter> -0500 by mkconf
Peter> cat /proc/partitions ---------
Peter> major minor #blocks name
Peter> 259 0 250059096 nvme0n1
Peter> 259 1 496640 nvme0n1p1
Peter> 259 2 1 nvme0n1p2
Peter> 259 3 63475712 nvme0n1p5
Peter> 259 4 97654784 nvme0n1p6
Peter> 259 5 37888 nvme0n1p7
Peter> 259 6 86913024 nvme0n1p8
Peter> 259 7 1474560 nvme0n1p9
Peter> 8 32 2930266584 sdc
Peter> 8 80 2930266584 sdf
Peter> 8 64 2930266584 sde
Peter> 8 48 2930266584 sdd
Peter> 8 16 2930266584 sdb
Peter> 8 0 2930266584 sda
Peter> 11 0 1048575 sr0
