Am Mi., 17. Nov. 2021 um 22:06 Uhr schrieb Wol <antlists@xxxxxxxxxxxxxxx>:
>
> On 17/11/2021 18:10, Martin Thoma wrote:
> > Thanks a lot.
> > Will try to get some new drives and do a dd and then will try to
> > assemble the Raid again.
> >
> > The Drives are CMR Drives, a few Western Digital and Seagate drives.
>
> Are they "raid friendly" though? What does "smartctl" tell you? Are the
> Seagates Barracudas (I hope not)?
>
> Whether before or after the copy, I'd look at the smartctl for the dodgy
> drives - they may have just been addled by the power fail but will be
> fine for backups, or they may have been on the way out and the power
> fail tipped them over the edge.
>
> Cheers,
> Wol
Hey,
some of the drives are indeed Seagate Baracudas. The two faulty drives
ist one Western Digital and the other a Toshiba
Here are the smartctl Data for those drives
/dev/sbc
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-21-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Green
Device Model: WDC WD30EZRX-00D8PB0
Serial Number: WD-WMC4N0E0NN71
LU WWN Device Id: 5 0014ee 6050ae2f5
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Nov 18 17:31:01 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (39120) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 393) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0027 185 166 021 Pre-fail
Always - 5708
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 668
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age
Always - 0
9 Power_On_Hours 0x0032 023 021 000 Old_age
Always - 56908
10 Spin_Retry_Count 0x0032 100 100 000 Old_age
Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 39
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age
Always - 23
193 Load_Cycle_Count 0x0032 117 117 000 Old_age
Always - 250280
194 Temperature_Celsius 0x0022 129 090 000 Old_age
Always - 21
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
/dev/sdd
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-21-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA HDWD130
Serial Number: 27R3EJDAS
LU WWN Device Id: 5 000039 fe6cfa767
Firmware Version: MX6OACF0
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Nov 18 17:31:33 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (21935) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 366) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 139 139 054 Pre-fail
Offline - 71
3 Spin_Up_Time 0x0007 130 130 024 Pre-fail
Always - 439 (Average 440)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 23
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail
Offline - 33
9 Power_On_Hours 0x0012 095 095 000 Old_age
Always - 39181
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 16
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age
Always - 1239
193 Load_Cycle_Count 0x0012 099 099 000 Old_age
Always - 1239
194 Temperature_Celsius 0x0002 222 222 000 Old_age
Always - 27 (Min/Max 23/67)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Again thanks a lot.
Regards
Martin
