I had a perfectly good software raid (md0) on my Linux Mint 19
installation. I replaced the motherboard, using the exact same drives as
before. However, now the RAID doesn't exist and won't assemble. I'm at
a loss as to how to best proceed without data loss at this point :(
# smartctl --xall /dev/sdc
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-42-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST MegaScale 4000
Device Model: HGST HMS5C4040ALE640
Serial Number: PL2331LAG5TWLJ
LU WWN Device Id: 5 000cca 22ec2a34a
Firmware Version: MPAOA3W0
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5700 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Dec 10 13:24:44 2018 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (43371) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 723) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 134 134 054 - 102
3 Spin_Up_Time POS--- 150 150 024 - 409
(Average 523)
4 Start_Stop_Count -O--C- 100 100 000 - 70
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 111 111 020 - 43
9 Power_On_Hours -O--C- 098 098 000 - 16964
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 70
192 Power-Off_Retract_Count -O--CK 100 100 000 - 130
193 Load_Cycle_Count -O--C- 100 100 000 - 130
194 Temperature_Celsius -O---- 187 187 000 - 32 (Min/Max
23/48)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 7 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x20 GPL R/O 1 Streaming performance log [OBS-8]
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 28/34 Celsius
Lifetime Min/Max Temperature: 23/48 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (57)
Index Estimated Time Temperature Celsius
58 2018-12-10 11:17 32 *************
59 2018-12-10 11:18 32 *************
60 2018-12-10 11:19 32 *************
61 2018-12-10 11:20 33 **************
62 2018-12-10 11:21 32 *************
63 2018-12-10 11:22 32 *************
64 2018-12-10 11:23 32 *************
65 2018-12-10 11:24 33 **************
66 2018-12-10 11:25 33 **************
67 2018-12-10 11:26 32 *************
68 2018-12-10 11:27 32 *************
69 2018-12-10 11:28 32 *************
70 2018-12-10 11:29 33 **************
71 2018-12-10 11:30 32 *************
... ..( 2 skipped). .. *************
74 2018-12-10 11:33 32 *************
75 2018-12-10 11:34 33 **************
76 2018-12-10 11:35 32 *************
77 2018-12-10 11:36 32 *************
78 2018-12-10 11:37 32 *************
79 2018-12-10 11:38 33 **************
80 2018-12-10 11:39 32 *************
... ..( 11 skipped). .. *************
92 2018-12-10 11:51 32 *************
93 2018-12-10 11:52 33 **************
94 2018-12-10 11:53 32 *************
95 2018-12-10 11:54 32 *************
96 2018-12-10 11:55 32 *************
97 2018-12-10 11:56 33 **************
98 2018-12-10 11:57 32 *************
... ..( 2 skipped). .. *************
101 2018-12-10 12:00 32 *************
102 2018-12-10 12:01 33 **************
103 2018-12-10 12:02 32 *************
... ..( 81 skipped). .. *************
57 2018-12-10 13:24 32 *************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 70 --- Lifetime Power-On Resets
0x01 0x010 4 16964 --- Power-on Hours
0x01 0x018 6 16707377456 --- Logical Sectors Written
0x01 0x020 6 19488649 --- Number of Write Commands
0x01 0x028 6 179576915499 --- Logical Sectors Read
0x01 0x030 6 754181879 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 16962 --- Spindle Motor Power-on Hours
0x03 0x010 4 16962 --- Head Flying Hours
0x03 0x018 4 130 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and
Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 32 --- Current Temperature
0x05 0x010 1 30 N-- Average Short Term Temperature
0x05 0x018 1 39 N-- Average Long Term Temperature
0x05 0x020 1 48 --- Highest Temperature
0x05 0x028 1 23 --- Lowest Temperature
0x05 0x030 1 44 N-- Highest Average Short Term Temperature
0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
0x05 0x040 1 42 N-- Highest Average Long Term Temperature
0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 1111 --- Number of Hardware Resets
0x06 0x010 4 537 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 7 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
# smartctl --xall /dev/sdd
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-42-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST MegaScale 4000
Device Model: HGST HMS5C4040ALE640
Serial Number: PL2331LAG5A0UJ
LU WWN Device Id: 5 000cca 22ec26b7e
Firmware Version: MPAOA3W0
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5700 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Dec 10 13:19:15 2018 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (44716) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 746) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 134 134 054 - 102
3 Spin_Up_Time POS--- 162 162 024 - 379
(Average 484)
4 Start_Stop_Count -O--C- 100 100 000 - 92
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 111 111 020 - 43
9 Power_On_Hours -O--C- 098 098 000 - 17927
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 85
192 Power-Off_Retract_Count -O--CK 100 100 000 - 153
193 Load_Cycle_Count -O--C- 100 100 000 - 153
194 Temperature_Celsius -O---- 133 133 000 - 45 (Min/Max
23/53)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 7 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x20 GPL R/O 1 Streaming performance log [OBS-8]
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 45 Celsius
Power Cycle Min/Max Temperature: 32/47 Celsius
Lifetime Min/Max Temperature: 23/53 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (72)
Index Estimated Time Temperature Celsius
73 2018-12-10 11:12 46 ***************************
... ..( 11 skipped). .. ***************************
85 2018-12-10 11:24 46 ***************************
86 2018-12-10 11:25 45 **************************
87 2018-12-10 11:26 46 ***************************
... ..( 11 skipped). .. ***************************
99 2018-12-10 11:38 46 ***************************
100 2018-12-10 11:39 45 **************************
101 2018-12-10 11:40 46 ***************************
102 2018-12-10 11:41 45 **************************
... ..( 6 skipped). .. **************************
109 2018-12-10 11:48 45 **************************
110 2018-12-10 11:49 46 ***************************
111 2018-12-10 11:50 45 **************************
... ..( 2 skipped). .. **************************
114 2018-12-10 11:53 45 **************************
115 2018-12-10 11:54 46 ***************************
116 2018-12-10 11:55 45 **************************
117 2018-12-10 11:56 45 **************************
118 2018-12-10 11:57 45 **************************
119 2018-12-10 11:58 46 ***************************
120 2018-12-10 11:59 45 **************************
... ..( 2 skipped). .. **************************
123 2018-12-10 12:02 45 **************************
124 2018-12-10 12:03 46 ***************************
125 2018-12-10 12:04 45 **************************
... ..( 6 skipped). .. **************************
4 2018-12-10 12:11 45 **************************
5 2018-12-10 12:12 46 ***************************
6 2018-12-10 12:13 45 **************************
7 2018-12-10 12:14 45 **************************
8 2018-12-10 12:15 45 **************************
9 2018-12-10 12:16 46 ***************************
10 2018-12-10 12:17 45 **************************
... ..( 2 skipped). .. **************************
13 2018-12-10 12:20 45 **************************
14 2018-12-10 12:21 46 ***************************
15 2018-12-10 12:22 45 **************************
16 2018-12-10 12:23 45 **************************
17 2018-12-10 12:24 45 **************************
18 2018-12-10 12:25 46 ***************************
19 2018-12-10 12:26 45 **************************
... ..( 2 skipped). .. **************************
22 2018-12-10 12:29 45 **************************
23 2018-12-10 12:30 46 ***************************
24 2018-12-10 12:31 45 **************************
... ..( 15 skipped). .. **************************
40 2018-12-10 12:47 45 **************************
41 2018-12-10 12:48 46 ***************************
42 2018-12-10 12:49 45 **************************
... ..( 29 skipped). .. **************************
72 2018-12-10 13:19 45 **************************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 85 --- Lifetime Power-On Resets
0x01 0x010 4 17927 --- Power-on Hours
0x01 0x018 6 15355180870 --- Logical Sectors Written
0x01 0x020 6 36795235 --- Number of Write Commands
0x01 0x028 6 203218097034 --- Logical Sectors Read
0x01 0x030 6 869532628 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 17921 --- Spindle Motor Power-on Hours
0x03 0x010 4 17921 --- Head Flying Hours
0x03 0x018 4 153 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and
Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 45 --- Current Temperature
0x05 0x010 1 43 N-- Average Short Term Temperature
0x05 0x018 1 42 N-- Average Long Term Temperature
0x05 0x020 1 53 --- Highest Temperature
0x05 0x028 1 23 --- Lowest Temperature
0x05 0x030 1 51 N-- Highest Average Short Term Temperature
0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
0x05 0x040 1 45 N-- Highest Average Long Term Temperature
0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 1164 --- Number of Hardware Resets
0x06 0x010 4 562 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
# mdadm --examine /dev/sda; mdadm --examine /dev/sdb; mdadm --examine
/dev/sdc; mdadm --examine /dev/sdd
/dev/sda:
MBR Magic : aa55
Partition[3] : 1953519616 sectors at 2048 (type 0f)
/dev/sdb:
MBR Magic : aa55
Partition[0] : 468862127 sectors at 1 (type ee)
/dev/sdc:
MBR Magic : aa55
Partition[0] : 4294967295 sectors at 1 (type ee)
/dev/sdd:
MBR Magic : aa55
Partition[0] : 4294967295 sectors at 1 (type ee)
# mdadm --examine /dev/sdc1; mdadm --examine /dev/sdd1
mdadm: No md superblock detected on /dev/sdc1.
mdadm: cannot open /dev/sdd1: No such file or directory
# mdadm --detail /dev/md0
mdadm: cannot open /dev/md0: No such file or directory
# lsdrv
PCI [ahci] 01:00.1 SATA controller: Advanced Micro Devices, Inc. [AMD]
Device 43c8 (rev 01)
├scsi 1:0:0:0 ATA Hitachi HDS72101 {JP2921HQ1PE8NA}
│└sda 931.51g [8:0] Partitioned (dos)
│ ├sda4 0.00k [8:4] Empty/Unknown
│ ├sda5 879.32g [8:5] ntfs 'BACKUP' {01CCB8FBEA021990}
│ │└Mounted as /dev/sda5 @ /mnt/BACKUP
│ ├sda6 2.00g [8:6] swap {2c560d1f-fb3f-4c95-996c-38ebe6091572}
│ └sda7 50.19g [8:7] ext4 'WINE' {5b7f4d75-874f-4b32-9eb7-f23c17e6c28b}
│ └Mounted as /dev/sda7 @ /mnt/WINE
├scsi 4:0:0:0 ATA KINGSTON SUV400S {50026B76820F91A4}
│└sdb 223.57g [8:16] Partitioned (gpt)
│ ├sdb1 221.66g [8:17] ext4 {b46f3ca6-7551-4926-bbbd-92296a63b795}
│ │└Mounted as /dev/sdb1 @ /
│ └sdb2 1.91g [8:18] swap {b80b828a-85b5-4059-9d34-ef17b40073af}
└scsi 5:0:0:0 ATA HGST HMS5C4040AL {PL2331LAG5TWLJ}
└sdc 3.64t [8:32] Partitioned (gpt)
└sdc1 3.64t [8:33] ext4 '4TB_HGST02'
{20fabea8-7514-449f-adf1-bf4ddab217f7}
PCI [ahci] 0a:00.2 SATA controller: Advanced Micro Devices, Inc. [AMD]
FCH SATA Controller [AHCI mode] (rev 51)
├scsi 10:0:0:0 HL-DT-ST DVDRAM GH24NS95 {K3MD4I95219}
│└sr0 1.00g [11:0] Empty/Unknown
└scsi 11:0:0:0 ATA HGST HMS5C4040AL {PL2331LAG5A0UJ}
└sdd 3.64t [8:48] Partitioned (gpt)
USB [usb-storage] Bus 003 Device 005: ID 13fd:1840 Initio Corporation
INIC-1608 SATA bridge {504E59303331353030303036}
└scsi 12:0:0:0 Generic External {PNY03150000691641765}
└sde 223.57g [8:64] Partitioned (dos)
Other Block Devices
├loop0 0.00k [7:0] Empty/Unknown
├loop1 0.00k [7:1] Empty/Unknown
├loop2 0.00k [7:2] Empty/Unknown
├loop3 0.00k [7:3] Empty/Unknown
├loop4 0.00k [7:4] Empty/Unknown
├loop5 0.00k [7:5] Empty/Unknown
├loop6 0.00k [7:6] Empty/Unknown
└loop7 0.00k [7:7] Empty/Unknown
# cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
[raid4] [raid10]
unused devices: <none>
