On 11/10/17 22:56, Joseba Ibarra wrote:
Hi Adam
root@grafico:/mnt# cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
[raid4] [raid10]
md0 : inactive sdd1[3] sdb1[1] sdc1[2]
2929889280 blocks super 1.2
unused devices: <none>
root@grafico:/mnt# mdadm --manage /dev/md0 --stop
mdadm: stopped /dev/md0
root@grafico:/mnt# mdadm --assemble /dev/md0 /dev/sd[bcd]1
mdadm: /dev/md0 assembled from 3 drives - not enough to start the
array while not clean - consider --force.
root@grafico:/mnt# cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
[raid4] [raid10]
unused devices: <none>
At this point I´ve followed the advise using --force
root@grafico:/mnt# mdadm --assemble --force /dev/md0 /dev/sd[bcd]1
mdadm: Marking array /dev/md0 as 'clean'
mdadm: /dev/md0 has been started with 3 drives (out of 4).
root@grafico:/mnt# cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5]
[raid4] [raid10]
md0 : active (auto-read-only) raid5 sdb1[1] sdd1[3] sdc1[2]
2929889280 blocks super 1.2 level 5, 512k chunk, algorithm 2
[4/3] [_UUU]
bitmap: 0/8 pages [0KB], 65536KB chunk
unused devices: <none>
Now I see the RAID, however can't be mounted. So, I'm not sure how to
backup the data. Gparted shows the partition /dev/md0p1 with the used
and free space.
It still says read-only, can you try:
mdadm --manage /dev/md0 --run
or
mdadm --manage /dev/md0 --readwrite
PS, usually mounting will automatically convert from readonly to
readwrite, but I recall some cases where this didn't happen for me, so
it might help you as well.
Regards,
Adam
Joseba Ibarra
Adam Goryachev <mailto:adam@xxxxxxxxxxxxxxxxxxxxxx>
11 de octubre de 2017, 13:29
Hi Rudy,
Please send the output of all of the following commands:
cat /proc/mdstat
mdadm --manage /dev/md0 --stop
mdadm --assemble /dev/md0 /dev/sd[bcd]1
cat /proc/mdstat
mdadm --manage /dev/md0 --run
mdadm --manage /dev/md0 --readwrite
cat /proc/mdstat
Basically the above is just looking at what the system has done
currently, stopping/clearing that, and then trying to assemble it
again, finally, we try to start it, even if it has one faulty disk.
At this stage, chances look good for recovering all your data, though
I would advise to get yourself a replacement disk for the dead one so
that you can restore redundancy as soon as possible.
Regards,Adam
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
