Last weekend I was moving a server with a raid1 configuration, controlled by a Intel Corporation 82801 SATA RAID Controller. Upon reboot I noticed the degraded message (server hadnt been rebooted in a couple years). The raid1 array was two 500gb black WD drives. I wasnt able to locate an identical 500gb disk, but did find a 2TB just to get things mirrored again. The bios screen accepted the replacement disk and said it would rebuild in the OS. mdsync seemed to do its thing but I noticed mdmon process was taking 200% cpu. I let it go a few days thinking it was just taking longer than normal to sync, then rebooted. It was in a complete failed state and wouldnt boot at all. After removing the 2TB disk I was able to boot into the OS again. I just assumed I needed a similar drive size for the second part of the mirror. Today I installed an identical black WD 500gb drive and its doing the same behavior. Currently running a bad block check but in the meantime I found the wiki and read up a bit on some basic troubleshooting and asking for help (https://raid.wiki.kernel.org/index.php/Asking_for_help) I wanted to attach the output of the commands on that page and hope someone may have some ideas for rebuilding this second drive. Thank you in advance for any suggestions. Im concerned at this point I only have one good drive and could possibly lose everything if that failed. mail:~ # smartctl --xall /dev/sda smartctl 6.0 2012-10-10 r3643 [i686-linux-3.1.10-1.29-pae] (SUSE RPM) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD5002AALX-00J37A0 Serial Number: WD-WMAYUL169523 LU WWN Device Id: 5 0014ee 104a23be3 Firmware Version: 15.01H15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Apr 12 09:33:54 2017 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 84) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 273 3 Spin_Up_Time POS--K 144 144 021 - 3783 4 Start_Stop_Count -O--CK 100 100 000 - 42 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 046 046 000 - 39646 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 39 192 Power-Off_Retract_Count -O--CK 200 200 000 - 36 193 Load_Cycle_Count -O--CK 200 200 000 - 5 194 Temperature_Celsius -O---K 104 104 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 9 198 Offline_Uncorrectable ----CK 200 200 000 - 7 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 15 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 24 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 209 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 209 [16] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:11:05.460 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:11:05.460 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:11:05.460 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:11:05.457 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:11:05.457 SET FEATURES [Set tra nsfer mode] Error 208 [15] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:11:03.702 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:11:03.702 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:11:03.702 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:11:03.701 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:11:03.701 SET FEATURES [Set tra nsfer mode] Error 207 [14] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:11:01.947 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:11:01.947 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:11:01.947 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:11:01.944 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:11:01.944 SET FEATURES [Set tra nsfer mode] Error 206 [13] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:11:00.189 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:11:00.189 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:11:00.189 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:11:00.188 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:11:00.188 SET FEATURES [Set tra nsfer mode] Error 205 [12] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:10:58.434 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:58.434 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:10:58.434 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:58.431 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:58.431 SET FEATURES [Set tra nsfer mode] Error 204 [11] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:10:56.681 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 01:10:56.660 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:56.659 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:10:56.659 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:56.658 IDENTIFY DEVICE Error 203 [10] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 h ours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:10:54.903 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:54.903 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:10:54.903 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:54.901 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:54.901 SET FEATURES [Set tra nsfer mode] Error 202 [9] occurred at disk power-on lifetime: 39645 hours (1651 days + 21 ho urs) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 13 34 8f 60 40 00 Error: UNC at LBA = 0x13348f60 = 32221 1680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 13 34 8f 60 40 08 01:10:53.148 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:53.147 SET FEATURES [Reserve d for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 01:10:53.146 READ NATIVE MAX ADDRE SS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:53.145 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:53.145 SET FEATURES [Set tra nsfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 30/39 Celsius Lifetime Min/Max Temperature: 0/39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (368) Index Estimated Time Temperature Celsius 369 2017-04-12 01:36 29 ********** ... ..(198 skipped). .. ********** 90 2017-04-12 04:55 29 ********** 91 2017-04-12 04:56 28 ********* 92 2017-04-12 04:57 29 ********** ... ..( 71 skipped). .. ********** 164 2017-04-12 06:09 29 ********** 165 2017-04-12 06:10 ? - 166 2017-04-12 06:11 30 *********** 167 2017-04-12 06:12 30 *********** 168 2017-04-12 06:13 30 *********** 169 2017-04-12 06:14 31 ************ 170 2017-04-12 06:15 32 ************* ... ..( 3 skipped). .. ************* 174 2017-04-12 06:19 32 ************* 175 2017-04-12 06:20 33 ************** 176 2017-04-12 06:21 33 ************** 177 2017-04-12 06:22 33 ************** 178 2017-04-12 06:23 34 *************** 179 2017-04-12 06:24 34 *************** 180 2017-04-12 06:25 35 **************** ... ..( 8 skipped). .. **************** 189 2017-04-12 06:34 35 **************** 190 2017-04-12 06:35 36 ***************** ... ..( 23 skipped). .. ***************** 214 2017-04-12 06:59 36 ***************** 215 2017-04-12 07:00 37 ****************** ... ..( 4 skipped). .. ****************** 220 2017-04-12 07:05 37 ****************** 221 2017-04-12 07:06 38 ******************* 222 2017-04-12 07:07 37 ****************** 223 2017-04-12 07:08 38 ******************* ... ..( 6 skipped). .. ******************* 230 2017-04-12 07:15 38 ******************* 231 2017-04-12 07:16 37 ****************** 232 2017-04-12 07:17 38 ******************* ... ..( 14 skipped). .. ******************* 247 2017-04-12 07:32 38 ******************* 248 2017-04-12 07:33 39 ******************** 249 2017-04-12 07:34 39 ******************** 250 2017-04-12 07:35 38 ******************* 251 2017-04-12 07:36 39 ******************** ... ..( 4 skipped). .. ******************** 256 2017-04-12 07:41 39 ******************** 257 2017-04-12 07:42 29 ********** ... ..(110 skipped). .. ********** 368 2017-04-12 09:33 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5831 Vendor specific mail:~ # mdadm --examine /dev/sda /dev/sda: Magic : Intel Raid ISM Cfg Sig. Version : 1.1.00 Orig Family : 80d98105 Family : 68a98654 Generation : 00b83763 Attributes : All supported UUID : 81a6fcf3:48d205e9:aa868e3f:9ad94fa5 Checksum : 7e0e85bb correct MPB Sectors : 2 Disks : 3 RAID Devices : 1 [Volume0]: UUID : 44c0fda9:b2d38c01:e48120f6:4bed6635 RAID Level : 1 Members : 2 Slots : [__] Failed disk : 1 This Slot : ? Array Size : 976766976 (465.76 GiB 500.10 GB) Per Dev Size : 976767240 (465.76 GiB 500.10 GB) Sector Offset : 0 Num Stripes : 3815496 Chunk Size : 64 KiB Reserved : 0 Migrate State : idle Map State : failed Dirty State : dirty Disk00 Serial : WD-WMAYUL169523 State : active failed Id : 00040000 Usable Size : 976766862 (465.76 GiB 500.10 GB) Disk01 Serial : WD-WCC6Y1VENZK4 State : active failed Id : 00050000 Usable Size : 976766862 (465.76 GiB 500.10 GB) Disk02 Serial : Z4Z6V3CV:0 State : active failed Id : ffffffff Usable Size : 3907022862 (1863.01 GiB 2000.40 GB) Disk Serial : WD-WMAYUL169523 State : active failed Id : 00040000 Usable Size : 976766862 (465.76 GiB 500.10 GB) mail:~ # mdadm --detail /dev/sda mdadm: /dev/sda does not appear to be an md device mail:~ # mdadm --detail /dev/md126 md126 md126p1 md126p2 mail:~ # mdadm --detail /dev/md126 md126 md126p1 md126p2 mail:~ # mdadm --detail /dev/md126 /dev/md126: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 488383488 (465.76 GiB 500.10 GB) Used Dev Size : 488383620 (465.76 GiB 500.10 GB) Raid Devices : 2 Total Devices : 1 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 UUID : 44c0fda9:b2d38c01:e48120f6:4bed6635 Number Major Minor RaidDevice State 1 8 0 0 active sync /dev/sda 1 0 0 1 removed mail:~ # mdadm --detail /dev/md127 /dev/md127: Version : imsm Raid Level : container Total Devices : 2 Working Devices : 2 UUID : 81a6fcf3:48d205e9:aa868e3f:9ad94fa5 Member Arrays : /dev/md126 Number Major Minor RaidDevice 0 8 16 - /dev/sdb 1 8 0 - /dev/sda mail:~/lsdrv # ./lsdrv PCI [ahci] 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 05) ├scsi 0:0:0:0 ATAPI iHAS424 B {3524253_2N8147500192} │└sr0 1.00g [11:0] Empty/Unknown ├scsi 1:x:x:x [Empty] ├scsi 2:x:x:x [Empty] ├scsi 3:x:x:x [Empty] ├scsi 4:0:0:0 ATA WDC WD5002AALX-0 {WD-WMAYUL169523} │└sda 465.76g [8:0] isw_raid_member │ ├md126 465.76g [9:126] MD vexternal:/md127/0 raid1 (2) active DEGRADED, 64k Chunk, recover (none) none {44c0fda9:b2d38c01:e48120f6:4bed6635} │ ││ Partitioned (dos) │ │├md126p1 4.01g [259:0] swap {57b97914-1b5f-4ac9-b7ca-c0e866535f68} │ │└md126p2 461.75g [259:1] Partitioned (dos) {bc3d52aa-a6d5-49a5-ab72-333b8dd5bc6d} │ │ └Mounted as /dev/md126p2 @ / │ ├md127 0.00k [9:127] MD vexternal:imsm () inactive, None (None) None {81a6fcf3:48d205e9:aa868e3f:9ad94fa5} │ │ Empty/Unknown │ ├sda1 4.01g [8:1] swap {57b97914-1b5f-4ac9-b7ca-c0e866535f68} │ └sda2 461.75g [8:2] Partitioned (dos) {bc3d52aa-a6d5-49a5-ab72-333b8dd5bc6d} └scsi 5:0:0:0 ATA WDC WD5003AZEX-0 {WD-WCC6Y1VENZK4} └sdb 465.76g [8:16] isw_raid_member └md127 0.00k [9:127] MD vexternal:imsm () inactive, None (None) None {81a6fcf3:48d205e9:aa868e3f:9ad94fa5} Empty/Unknown PCI [sata_sil24] 04:00.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 02) ├scsi 6:x:x:x [Empty] ├scsi 7:x:x:x [Empty] ├scsi 8:x:x:x [Empty] └scsi 9:x:x:x [Empty] mail:~/lsdrv # cat /proc/mdstat Personalities : [raid1] [raid0] [raid10] [raid6] [raid5] [raid4] md126 : active raid1 sda[1] 488383488 blocks super external:/md127/0 [2/1] [U_] md127 : inactive sda[1](S) sdb[0](S) 5928 blocks super external:imsm unused devices: <none> mail:~/lsdrv # -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
