On Tue, 30 Jul 2013 21:24:24 +0200 Martin Wilck <mwilck@xxxxxxxx> wrote: > On 07/30/2013 03:34 AM, NeilBrown wrote: > > On Fri, 26 Jul 2013 23:06:01 +0200 Martin Wilck <mwilck@xxxxxxxx> wrote: > > > >> Hi Neil, > >> > >> here is another question. 2 years ago you committed c7079c84 "ddf: > >> remove failed devices that are no longer in use", with the reasoning "it > >> isn't clear what (a phys disk record for every physically attached > >> device) means in the case of soft raid in a general purpose Linux computer". > >> > >> I am not sure if this was correct. A common use case for DDF is an > >> actual BIOS fake RAID, possibly dual-boot with a vendor soft-RAID driver > >> under Windows. Such other driver might be highly confused by mdadm > >> auto-removing devices. Not even "missing" devices need to be removed > >> from the meta data in DDF; they can be simply marked "missing". > >> > >> May I ask you to reconsider this, and possibly revert c7079c84? > >> Martin > > > > You may certainly ask .... > > > > I presumably had a motivation for that change. Unfortunately I didn't record > > the motivation, only the excuse. > > > > It probably comes down to a question of when *do* you remove phys disk > > records? > > I think that if I revert that patch we could get a situation where we keep > > adding new phys disk records and fill up some table. > > How is this handled with native meta data? IMSM? Is there any reason to > treat DDF special? In a hw RAID scenario, the user would remove the > failed disk physically sooner or later, and it would switch to "missing" > state. So here, I'd expect the user to call mdadm --remove. Native metadata doesn't really differentiate between 'device has failed' and 'device isn't present'. There are bits in the 0.90 format that can tell the difference, but the two states are treated the same. When a device fails it transition for 'working' to 'failed but still present'. Then when you "mdadm --remove" it transitions to "not present". But it is not possible to go back to "failed but still present". i.e. if you shut down the array and then start it up again, any devices that have failed will not be included. If they have failed then you possibly cannot read the metadata and you may not know that they "should" be included. DDF is designed to work in the firmware of card which have a limited number of port which they have complete control of. So they may be able to "know" that a device is present even if it isn't worked. mdadm is designed with the same or of perspective. If a device is working enough to read the metadata it would be possible to include it in the contain even if it is being treated as 'failed'. Not sure how much work it would be to achieve this. If a device is working enough to be detected on the bus, but not enough to read the metadata, then you could only include it in the container if some config information said "These ports all belong to that container". I doubt that would be worth the effort. > > We already have find_unused_pde(). We could make this function try > harder - when no empty slot is found, look for slots with > "missing|failed" and then "missing" (or "failed"?) disks, and replace > those with the new disk. Yes, that could work. > > > We should probably be recording some sort of WWN or path identifier in the > > metadata and then have md check in /dev/disk/by-XXX to decide if the device > > has really disappeared or is just failed. > > Look for "Cannot be bothered" in super-ddf.c :-) > This is something that waits to be implemented, for SAS/SATA at least. :-) I'm hoping someone will turn up who can be bothered... > > > Maybe the 'path' field in phys_disk_entry could/should be used here. However > > we the BIOS might interpret that in a specific way that mdadm would need to > > agree with.... > > > > If we can come up with a reasonably reliable way to remove phys disk records > > at an appropriate time, I'm happy to revert this patch. Until then I'm not > > sure it is a good idea..... > > > > But I'm open to being convinced. > > Well, me too, I may be wrong, after all. Perhaps auto-removal is ok. I > need to try it with fake RAID. If you can determine that the current behaviour confuses some BIOS, then clearly we should fix it. If not, then the bar for acceptance of changes would probably be a little higher. As long as it isn't easy to get a growth of lots of 'failed' entries in the table I can probably be happy. NeilBrown
Attachment:
signature.asc
Description: PGP signature
