Hi Phil,
In article <510BC173.7070002@xxxxxxxxxx> you wrote:
>> So the situation is: I have a four-disk RAID5 with two active disks, and
>> two that dropped out at different times.
>
> Please show the errors from dmesg.
I don't think I can provide that. The RAID ran in a QNAP system, and if
there is a log at all, it's on this disk...
During the copy process, it was all media errors, however.
> And show "smartctl -x" for the drives that failed.
See below.
[...]
> Also show "mdadm -E" for all of the member devices. This data is an
> absolute *must* before any major surgery on an array.
also below.
>> My first attempt would be to try
>> mdadm --create --metadata=0.9 --chunk=64 --assume-clean, etc.
>>
>> Is there a chance for this to succeed? Or do you have better suggestions?
>
> "--create" is a *terrible* first step. "mdadm --assemble --force" is
> the right tool for this job.
I forgot to mention: I tried that, and stopped it, after I saw the first
thing it did was to start a rebuild of the array. I couldn't figure out
which disk it was trying to rebuild, but whichever of the two dropped out
disks it was, I can't see how it could reconstruct the data once it reaches
the point of the errors on the disk it uses in the reconstruction.
(So "first" above should really say more verbose "first after the new copies
are finished".)
mdadm --assemble --assume-clean sounded like the most logical combination of
options, but was rejected.
Unfortunately, the data on the disk is not simply a filesystem where bad
blocks mean a few unreadable files, but a filesystem with a number of files
on it that represent a volume exported by iSCSI, on which there is an
encrypted partition with a filesystem. So I'm not too sure, if any of these
indirections badly multiplies the effect of a single bad sector, and I'm
trying to reach 100% good, if possible.
>> If all recovery that involves assembling the array fails: Is is possible
>> to manually assemble the data?
>> I'm thinking in the direction of: take the first 64k from disk1, then 64k
>> from disk2, etc.? This would probably take years to complete, but the data
>> is of really big importance to me (which is why I put it on a RAID in the
>> first place...).
>
> Your scenario sounds like the common timeout mismatch catastrophe, which
> is why I asked for "smartctl -x". If that is the case, MD won't be able
> to do the reconstructions that it should when encounting read errors.
You mean the "timeout of the disk is longer than RAID's patience" problem?
I have no idea, if the old disks suffered from it, I used Samsung HD204UI
which were certified by QNAP. The copies are now WD NAS edition disks,
which have a lower timeout.
> Also, you have a poor understanding of MD's use--it is *not* a backup
> alternative. It is a tool for maximizing *uptime*. It will keep you
> running through the normal random failures that complex
> electro-mechanical systems experience.
>
> MD won't save your data from accidental deletion or other operator
> error. It won't save your data from a lightning strike. It won't save
> your data from a home or office fire. You still need to make backups.
I'm all too aware of that, and we also tryied to keep a "manual RAID" by
copying to a number of USB disks stored at a different location to survive a
burnt-down house. However, this event uncovered a bad oversight on our
side in that process. We simply missed some data under certain circumstances
(the "I-thought-you-did-it" bug in human interaction). So out of the ~800GB
on the RAID, for some +/-20GB, this is the only remaining copy.
Recently, I also started copying all data to Amazon Glacier, for 100%-epsilon
reliable storage, but this upload simply took longer than the disks lasted
(=less than 30 days spinning! very disappointing).
Regards,
Michael
All the disk data: disk 1 and 3 failed:
(I installed the patch for the firmware bug from December 2012.)
Disk1:
======
/dev/sdc3:
Magic : a92b4efc
Version : 0.90.00
UUID : f5ad617a:14ccd4b1:3d7a38e4:71465fe8
Creation Time : Fri Nov 26 19:58:40 2010
Raid Level : raid5
Used Dev Size : 1951945600 (1861.52 GiB 1998.79 GB)
Array Size : 5855836800 (5584.56 GiB 5996.38 GB)
Raid Devices : 4
Total Devices : 4
Preferred Minor : 0
Update Time : Fri Jan 4 15:11:07 2013
State : active
Active Devices : 4
Working Devices : 4
Failed Devices : 0
Spare Devices : 0
Checksum : 7496591c - correct
Events : 25
Layout : left-symmetric
Chunk Size : 64K
Number Major Minor RaidDevice State
this 0 8 3 0 active sync
0 0 8 3 0 active sync
1 1 8 19 1 active sync /dev/sdb3
2 2 8 35 2 active sync /dev/sdc3
3 3 8 51 3 active sync
Disk2:
======
/dev/sdb3:
Magic : a92b4efc
Version : 0.90.00
UUID : f5ad617a:14ccd4b1:3d7a38e4:71465fe8
Creation Time : Fri Nov 26 19:58:40 2010
Raid Level : raid5
Used Dev Size : 1951945600 (1861.52 GiB 1998.79 GB)
Array Size : 5855836800 (5584.56 GiB 5996.38 GB)
Raid Devices : 4
Total Devices : 3
Preferred Minor : 0
Update Time : Fri Jan 4 16:33:36 2013
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 1
Spare Devices : 0
Checksum : 74966e44 - correct
Events : 237
Layout : left-symmetric
Chunk Size : 64K
Number Major Minor RaidDevice State
this 1 8 19 1 active sync /dev/sdb3
0 0 0 0 0 removed
1 1 8 19 1 active sync /dev/sdb3
2 2 0 0 2 faulty removed
3 3 8 51 3 active sync
Disk3:
======
/dev/sdb3:
Magic : a92b4efc
Version : 0.90.00
UUID : f5ad617a:14ccd4b1:3d7a38e4:71465fe8
Creation Time : Fri Nov 26 19:58:40 2010
Raid Level : raid5
Used Dev Size : 1951945600 (1861.52 GiB 1998.79 GB)
Array Size : 5855836800 (5584.56 GiB 5996.38 GB)
Raid Devices : 4
Total Devices : 3
Preferred Minor : 0
Update Time : Fri Jan 4 16:32:27 2013
State : clean
Active Devices : 3
Working Devices : 3
Failed Devices : 0
Spare Devices : 0
Checksum : 74966e04 - correct
Events : 236
Layout : left-symmetric
Chunk Size : 64K
Number Major Minor RaidDevice State
this 2 8 35 2 active sync /dev/sdc3
0 0 0 0 0 removed
1 1 8 19 1 active sync /dev/sdb3
2 2 8 35 2 active sync /dev/sdc3
3 3 8 51 3 active sync
Disk4:
======
/dev/sdc3:
Magic : a92b4efc
Version : 0.90.00
UUID : f5ad617a:14ccd4b1:3d7a38e4:71465fe8
Creation Time : Fri Nov 26 19:58:40 2010
Raid Level : raid5
Used Dev Size : 1951945600 (1861.52 GiB 1998.79 GB)
Array Size : 5855836800 (5584.56 GiB 5996.38 GB)
Raid Devices : 4
Total Devices : 3
Preferred Minor : 0
Update Time : Fri Jan 4 16:33:36 2013
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 1
Spare Devices : 0
Checksum : 74966e68 - correct
Events : 237
Layout : left-symmetric
Chunk Size : 64K
Number Major Minor RaidDevice State
this 3 8 51 3 active sync
0 0 0 0 0 removed
1 1 8 19 1 active sync /dev/sdb3
2 2 0 0 2 faulty removed
3 3 8 51 3 active sync
Disk1:
======
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AFT)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J1BZA16176
LU WWN Device Id: 5 0024e9 004358105
Firmware Version: 1AQ10001
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Feb 1 20:33:54 2013 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=386
http://sourceforge.net/apps/trac/smartmontools/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 119) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (20640) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1121
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 066 065 025 - 10415
4 Start_Stop_Count -O--CK 099 099 000 - 1123
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 717
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 120
181 Program_Fail_Cnt_Total -O---K 100 100 000 - 903
191 G-Sense_Error_Rate -O---K 100 100 000 - 3
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 064 000 - 17 (Min/Max 14/33)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 100 100 000 - 30
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 0
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 1124
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 1005 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1005 [4] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.277 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.277 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.277 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.277 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.277 READ NATIVE MAX ADDRESS EXT
Error 1004 [3] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.271 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.271 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.271 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.271 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.271 READ NATIVE MAX ADDRESS EXT
Error 1003 [2] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.266 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.266 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.266 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.266 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.266 READ NATIVE MAX ADDRESS EXT
Error 1002 [1] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.261 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.261 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.261 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.261 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.261 READ NATIVE MAX ADDRESS EXT
Error 1001 [0] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.256 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.256 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.256 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.256 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.256 READ NATIVE MAX ADDRESS EXT
Error 1000 [7] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.251 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.251 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.251 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.251 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.251 READ NATIVE MAX ADDRESS EXT
Error 999 [6] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.246 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.246 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.246 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.246 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.246 READ NATIVE MAX ADDRESS EXT
Error 998 [5] occurred at disk power-on lifetime: 716 hours (29 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 13 a4 a7 88 e0 00 Error: UNC 8 sectors at LBA = 0x13a4a788 = 329557896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 13 a4 a7 88 e0 00 00:01:16.241 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.241 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:16.241 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:01:16.241 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:16.241 READ NATIVE MAX ADDRESS EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 70% 698 327170640
# 2 Extended offline Completed: read failure 90% 693 327170208
# 3 Short offline Completed: read failure 10% 692 327170648
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed_read_failure [70% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 17 Celsius
Power Cycle Min/Max Temperature: 16/17 Celsius
Lifetime Min/Max Temperature: 14/67 Celsius
Lifetime Average Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (104)
Index Estimated Time Temperature Celsius
105 2013-02-01 09:55 17 -
106 2013-02-01 10:00 29 **********
107 2013-02-01 10:05 28 *********
... ..( 15 skipped). .. *********
123 2013-02-01 11:25 28 *********
124 2013-02-01 11:30 29 **********
125 2013-02-01 11:35 28 *********
... ..( 9 skipped). .. *********
7 2013-02-01 12:25 28 *********
8 2013-02-01 12:30 29 **********
... ..( 9 skipped). .. **********
18 2013-02-01 13:20 29 **********
19 2013-02-01 13:25 28 *********
20 2013-02-01 13:30 29 **********
... ..( 6 skipped). .. **********
27 2013-02-01 14:05 29 **********
28 2013-02-01 14:10 28 *********
29 2013-02-01 14:15 29 **********
30 2013-02-01 14:20 28 *********
31 2013-02-01 14:25 28 *********
32 2013-02-01 14:30 28 *********
33 2013-02-01 14:35 29 **********
34 2013-02-01 14:40 28 *********
... ..( 9 skipped). .. *********
44 2013-02-01 15:30 28 *********
45 2013-02-01 15:35 29 **********
46 2013-02-01 15:40 28 *********
... ..( 7 skipped). .. *********
54 2013-02-01 16:20 28 *********
55 2013-02-01 16:25 29 **********
56 2013-02-01 16:30 28 *********
57 2013-02-01 16:35 29 **********
58 2013-02-01 16:40 28 *********
59 2013-02-01 16:45 28 *********
60 2013-02-01 16:50 27 ********
61 2013-02-01 16:55 28 *********
62 2013-02-01 17:00 29 **********
63 2013-02-01 17:05 28 *********
... ..( 13 skipped). .. *********
77 2013-02-01 18:15 28 *********
78 2013-02-01 18:20 29 **********
79 2013-02-01 18:25 28 *********
... ..( 14 skipped). .. *********
94 2013-02-01 19:40 28 *********
95 2013-02-01 19:45 27 ********
96 2013-02-01 19:50 28 *********
97 2013-02-01 19:55 28 *********
98 2013-02-01 20:00 27 ********
... ..( 5 skipped). .. ********
104 2013-02-01 20:30 27 ********
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 7 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
Disk2:
======
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AFT)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J1BZA16132
LU WWN Device Id: 5 0024e9 004357e94
Firmware Version: 1AQ10001
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Feb 1 20:28:32 2013 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=386
http://sourceforge.net/apps/trac/smartmontools/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (20760) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 067 066 025 - 10206
4 Start_Stop_Count -O--CK 099 099 000 - 1124
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 709
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 128
181 Program_Fail_Cnt_Total -O---K 100 100 000 - 925
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 064 000 - 21 (Min/Max 14/35)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 0
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 1126
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 697 -
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 21 Celsius
Power Cycle Min/Max Temperature: 20/21 Celsius
Lifetime Min/Max Temperature: 14/62 Celsius
Lifetime Average Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (2)
Index Estimated Time Temperature Celsius
3 2013-02-01 09:50 21 **
4 2013-02-01 09:55 26 *******
5 2013-02-01 10:00 24 *****
6 2013-02-01 10:05 24 *****
7 2013-02-01 10:10 25 ******
8 2013-02-01 10:15 25 ******
9 2013-02-01 10:20 18 -
10 2013-02-01 10:25 19 -
11 2013-02-01 10:30 21 **
12 2013-02-01 10:35 22 ***
13 2013-02-01 10:40 23 ****
14 2013-02-01 10:45 24 *****
15 2013-02-01 10:50 24 *****
16 2013-02-01 10:55 25 ******
17 2013-02-01 11:00 25 ******
18 2013-02-01 11:05 26 *******
19 2013-02-01 11:10 26 *******
20 2013-02-01 11:15 26 *******
21 2013-02-01 11:20 27 ********
22 2013-02-01 11:25 26 *******
23 2013-02-01 11:30 27 ********
... ..( 4 skipped). .. ********
28 2013-02-01 11:55 27 ********
29 2013-02-01 12:00 28 *********
30 2013-02-01 12:05 27 ********
31 2013-02-01 12:10 27 ********
32 2013-02-01 12:15 18 -
33 2013-02-01 12:20 19 -
34 2013-02-01 12:25 20 *
35 2013-02-01 12:30 22 ***
36 2013-02-01 12:35 23 ****
37 2013-02-01 12:40 18 -
38 2013-02-01 12:45 19 -
39 2013-02-01 12:50 21 **
40 2013-02-01 12:55 22 ***
41 2013-02-01 13:00 24 *****
42 2013-02-01 13:05 24 *****
43 2013-02-01 13:10 24 *****
44 2013-02-01 13:15 25 ******
45 2013-02-01 13:20 25 ******
46 2013-02-01 13:25 26 *******
47 2013-02-01 13:30 26 *******
48 2013-02-01 13:35 19 -
49 2013-02-01 13:40 22 ***
50 2013-02-01 13:45 24 *****
51 2013-02-01 13:50 26 *******
52 2013-02-01 13:55 27 ********
53 2013-02-01 14:00 29 **********
54 2013-02-01 14:05 30 ***********
55 2013-02-01 14:10 31 ************
56 2013-02-01 14:15 31 ************
57 2013-02-01 14:20 32 *************
58 2013-02-01 14:25 32 *************
59 2013-02-01 14:30 32 *************
60 2013-02-01 14:35 33 **************
... ..( 2 skipped). .. **************
63 2013-02-01 14:50 33 **************
64 2013-02-01 14:55 32 *************
65 2013-02-01 15:00 33 **************
66 2013-02-01 15:05 33 **************
67 2013-02-01 15:10 34 ***************
68 2013-02-01 15:15 33 **************
69 2013-02-01 15:20 34 ***************
70 2013-02-01 15:25 34 ***************
71 2013-02-01 15:30 33 **************
72 2013-02-01 15:35 33 **************
73 2013-02-01 15:40 34 ***************
... ..( 46 skipped). .. ***************
120 2013-02-01 19:35 34 ***************
121 2013-02-01 19:40 33 **************
122 2013-02-01 19:45 33 **************
123 2013-02-01 19:50 35 ****************
124 2013-02-01 19:55 34 ***************
125 2013-02-01 20:00 34 ***************
126 2013-02-01 20:05 33 **************
... ..( 3 skipped). .. **************
2 2013-02-01 20:25 33 **************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
Disk 3:
=======
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AFT)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J1BZA16147
LU WWN Device Id: 5 0024e9 004357edb
Firmware Version: 1AQ10001
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Feb 1 20:33:49 2013 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=386
http://sourceforge.net/apps/trac/smartmontools/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 116) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (21000) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 29439
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 067 066 025 - 10221
4 Start_Stop_Count -O--CK 099 099 000 - 1130
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 766
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 133
181 Program_Fail_Cnt_Total -O---K 100 100 000 - 919
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 064 000 - 18 (Min/Max 14/35)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 081 081 000 - 2350
198 Offline_Uncorrectable ----CK 252 100 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 0
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 1132
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 21341 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 21341 [4] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.113 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.113 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.113 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.113 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.113 READ NATIVE MAX ADDRESS EXT
Error 21340 [3] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.108 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.108 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.108 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.108 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.108 READ NATIVE MAX ADDRESS EXT
Error 21339 [2] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.103 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.103 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.103 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.103 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.103 READ NATIVE MAX ADDRESS EXT
Error 21338 [1] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.098 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.098 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.098 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.098 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.098 READ NATIVE MAX ADDRESS EXT
Error 21337 [0] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.093 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.093 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.093 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.093 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.093 READ NATIVE MAX ADDRESS EXT
Error 21336 [7] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 70 e0 00 Error: UNC 8 sectors at LBA = 0x2c887270 = 747139696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 70 e0 00 00:00:50.087 READ DMA EXT
25 00 00 00 08 00 00 2c 88 72 78 e0 00 00:00:50.087 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.087 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.087 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.087 SET FEATURES [Set transfer mode]
Error 21335 [6] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 b8 e0 00 Error: UNC 8 sectors at LBA = 0x2c8872b8 = 747139768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 b8 e0 00 00:00:50.082 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.082 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.082 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.082 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.082 READ NATIVE MAX ADDRESS EXT
Error 21334 [5] occurred at disk power-on lifetime: 766 hours (31 days + 22 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 2c 88 72 b8 e0 00 Error: UNC 8 sectors at LBA = 0x2c8872b8 = 747139768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 2c 88 72 b8 e0 00 00:00:50.077 READ DMA EXT
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.077 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:50.077 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:50.077 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:50.077 READ NATIVE MAX ADDRESS EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 40% 766 329136144
# 2 Short offline Completed: read failure 10% 745 717909280
# 3 Short offline Completed: read failure 70% 714 327191864
# 4 Extended offline Completed: read failure 90% 695 329136144
# 5 Short offline Completed: read failure 80% 695 724561192
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed_read_failure [40% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 17 Celsius
Power Cycle Min/Max Temperature: 15/17 Celsius
Lifetime Min/Max Temperature: 13/67 Celsius
Lifetime Average Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (5)
Index Estimated Time Temperature Celsius
6 2013-02-01 09:55 17 -
7 2013-02-01 10:00 27 ********
... ..( 24 skipped). .. ********
32 2013-02-01 12:05 27 ********
33 2013-02-01 12:10 26 *******
34 2013-02-01 12:15 27 ********
... ..( 29 skipped). .. ********
64 2013-02-01 14:45 27 ********
65 2013-02-01 14:50 28 *********
66 2013-02-01 14:55 27 ********
... ..( 22 skipped). .. ********
89 2013-02-01 16:50 27 ********
90 2013-02-01 16:55 26 *******
91 2013-02-01 17:00 27 ********
... ..( 5 skipped). .. ********
97 2013-02-01 17:30 27 ********
98 2013-02-01 17:35 26 *******
99 2013-02-01 17:40 26 *******
100 2013-02-01 17:45 27 ********
101 2013-02-01 17:50 26 *******
102 2013-02-01 17:55 27 ********
103 2013-02-01 18:00 26 *******
... ..( 6 skipped). .. *******
110 2013-02-01 18:35 26 *******
111 2013-02-01 18:40 27 ********
112 2013-02-01 18:45 27 ********
113 2013-02-01 18:50 26 *******
114 2013-02-01 18:55 26 *******
115 2013-02-01 19:00 27 ********
... ..( 2 skipped). .. ********
118 2013-02-01 19:15 27 ********
119 2013-02-01 19:20 26 *******
120 2013-02-01 19:25 26 *******
121 2013-02-01 19:30 27 ********
122 2013-02-01 19:35 26 *******
123 2013-02-01 19:40 27 ********
124 2013-02-01 19:45 27 ********
125 2013-02-01 19:50 26 *******
... ..( 3 skipped). .. *******
1 2013-02-01 20:10 26 *******
2 2013-02-01 20:15 27 ********
3 2013-02-01 20:20 27 ********
4 2013-02-01 20:25 26 *******
5 2013-02-01 20:30 26 *******
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 1 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
Disk 4:
=======
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AFT)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J1BZA16596
LU WWN Device Id: 5 0024e9 00435a3ba
Firmware Version: 1AQ10001
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Feb 1 20:30:17 2013 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=386
http://sourceforge.net/apps/trac/smartmontools/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (20820) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 067 060 025 - 10215
4 Start_Stop_Count -O--CK 099 099 000 - 1134
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 722
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 144
181 Program_Fail_Cnt_Total -O---K 100 100 000 - 926
191 G-Sense_Error_Rate -O---K 100 100 000 - 3
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 063 000 - 21 (Min/Max 14/37)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 0
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 1147
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 717 -
# 2 Short offline Completed without error 00% 707 -
# 3 Short offline Completed without error 00% 693 -
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 21 Celsius
Power Cycle Min/Max Temperature: 20/22 Celsius
Lifetime Min/Max Temperature: 13/65 Celsius
Lifetime Average Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (108)
Index Estimated Time Temperature Celsius
109 2013-02-01 09:55 22 ***
110 2013-02-01 10:00 31 ************
... ..( 4 skipped). .. ************
115 2013-02-01 10:25 31 ************
116 2013-02-01 10:30 30 ***********
117 2013-02-01 10:35 31 ************
... ..( 52 skipped). .. ************
42 2013-02-01 15:00 31 ************
43 2013-02-01 15:05 26 *******
44 2013-02-01 15:10 28 *********
45 2013-02-01 15:15 30 ***********
46 2013-02-01 15:20 31 ************
47 2013-02-01 15:25 32 *************
48 2013-02-01 15:30 33 **************
49 2013-02-01 15:35 34 ***************
50 2013-02-01 15:40 35 ****************
51 2013-02-01 15:45 35 ****************
52 2013-02-01 15:50 37 ******************
53 2013-02-01 15:55 36 *****************
... ..( 9 skipped). .. *****************
63 2013-02-01 16:45 36 *****************
64 2013-02-01 16:50 35 ****************
65 2013-02-01 16:55 36 *****************
... ..( 4 skipped). .. *****************
70 2013-02-01 17:20 36 *****************
71 2013-02-01 17:25 37 ******************
72 2013-02-01 17:30 36 *****************
... ..( 11 skipped). .. *****************
84 2013-02-01 18:30 36 *****************
85 2013-02-01 18:35 37 ******************
86 2013-02-01 18:40 36 *****************
87 2013-02-01 18:45 36 *****************
88 2013-02-01 18:50 37 ******************
89 2013-02-01 18:55 36 *****************
90 2013-02-01 19:00 36 *****************
91 2013-02-01 19:05 36 *****************
92 2013-02-01 19:10 37 ******************
93 2013-02-01 19:15 36 *****************
94 2013-02-01 19:20 36 *****************
95 2013-02-01 19:25 35 ****************
... ..( 11 skipped). .. ****************
107 2013-02-01 20:25 35 ****************
108 2013-02-01 20:30 21 **
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
