On 8/17/2012 6:16 AM, Miquel van Smoorenburg wrote: > On 08/17/2012 09:31 AM, Stan Hoeppner wrote: >> On 8/16/2012 4:50 PM, Miquel van Smoorenburg wrote: >>> I did a simple test: >>> >>> * created a 1G partition on 3 seperate disks >>> * created a md raid5 array with 512K chunksize: >>> mdadm -C /dev/md0 -l 5 -c $((1024*512)) -n 3 /dev/sdb1 /dev/sdc1 >>> /dev/sdd1 >>> * ran disk monitoring using 'iostat -k 5 /dev/sdb1 /dev/sdc1 /dev/sdd1' >>> * wrote a single 4K block: >>> dd if=/dev/zero bs=4K count=1 oflag=direct seek=30 of=/dev/md0 >>> >>> Output from iostat over the period in which the 4K write was done. Look >>> at kB read and kB written: >>> >>> Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn >>> sdb1 0.60 0.00 1.60 0 8 >>> sdc1 0.60 0.80 0.80 4 4 >>> sdd1 0.60 0.00 1.60 0 8 >>> >>> As you can see, a single 4K read, and a few writes. You see a few blocks >>> more written that you'd expect because the superblock is updated too. >> >> I'm no dd expert, but this looks like you're simply writing a 4KB block >> to a new stripe, using an offset, but not to an existing stripe, as the >> array is in a virgin state. So it doesn't appear this test is going to >> trigger RMW. Don't you need now need to do another write in the same >> stripe to to trigger RMW? Maybe I'm just reading this wrong. > > That shouldn't matter, but that is easily checked ofcourse, by writing > some random random data first, then doing the dd 4K write also with > random data somewhere in the same area: > > # dd if=/dev/urandom bs=1M count=3 of=/dev/md0 > 3+0 records in > 3+0 records out > 3145728 bytes (3.1 MB) copied, 0.794494 s, 4.0 MB/s > > Now the first 6 chunks are filled with random data, let write 4K > somewhere in there: > > # dd if=/dev/urandom bs=4k count=1 seek=25 of=/dev/md0 > 1+0 records in > 1+0 records out > 4096 bytes (4.1 kB) copied, 0.10149 s, 40.4 kB/s > > Output from iostat over the period in which the 4K write was done: > > Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn > sdb1 0.60 0.00 1.60 0 8 > sdc1 0.60 0.80 0.80 4 4 > sdd1 0.60 0.00 1.60 0 8 According to your iostat output, the IO is identical for both tests. So either you triggered an RMW in the first test, or you haven't triggered an RMW with either test. Your fist test shouldn't have triggered RMW. The second one should have. BTW, I'm curious why you replied to my message posted to linux-raid, then stripped linux-raid from the CC list and added lkml proper. What was the reason for this? I'm adding linux-raid and removing lkml. -- Stan -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
