On Sun November 1 2009, Justin Piszcz wrote:
> On Sun, 1 Nov 2009, Thomas Fjellstrom wrote:
> > My main raid array just had a disk failure. I tried to hot remove the
> > device, and use the scsi bus rescan sysfs entries, but it seems to fail
> > on IDENTIFY.
> >
> > Can I assume my disk is dead?
> >
> >
> > [5015721.851044] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action
> > 0x0 [5015721.851089] ata3.00: irq_stat 0x40000001
> > [5015721.851124] ata3.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
> > [5015721.851125] res 71/04:03:80:01:32/00:00:00:00:00/e0 Emask
> > 0x1 (device error)
> > [5015721.851193] ata3.00: status: { DRDY DF ERR }
> > [5015721.851225] ata3.00: error: { ABRT }
> > [5015726.848684] ata3.00: qc timeout (cmd 0xec)
> > [5015726.848729] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
> > [5015726.848763] ata3.00: revalidation failed (errno=-5)
> > [5015726.848798] ata3: hard resetting link
> > [5015734.501527] ata3: softreset failed (device not ready)
> > [5015734.501565] ata3: failed due to HW bug, retry pmp=0
> > [5015734.665530] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > [5015734.707085] ata3.00: both IDENTIFYs aborted, assuming NODEV
> > [5015734.707089] ata3.00: revalidation failed (errno=-2)
> > [5015739.664923] ata3: hard resetting link
> > [5015740.148277] ata3: softreset failed (device not ready)
> > [5015740.148314] ata3: failed due to HW bug, retry pmp=0
> > [5015740.313532] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > [5015740.337129] ata3.00: both IDENTIFYs aborted, assuming NODEV
> > [5015740.337132] ata3.00: revalidation failed (errno=-2)
> > [5015740.337167] ata3.00: disabled
> > [5015740.337231] ata3: EH complete
> > [5015740.337275] sd 2:0:0:0: [sdc] Unhandled error code
> > [5015740.337308] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> > [5015740.337372] end_request: I/O error, dev sdc, sector 1250258495
> > [5015740.337410] end_request: I/O error, dev sdc, sector 1250258495
> > [5015740.337445] md: super_written gets error=-5, uptodate=0
> > [5015740.337479] raid5: Disk failure on sdc1, disabling device.
> > [5015740.337480] raid5: Operation continuing on 3 devices.
> > [5015740.337569] sd 2:0:0:0: [sdc] Unhandled error code
> > [5015740.337601] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> > [5015740.337665] end_request: I/O error, dev sdc, sector 480014231
> > [5015740.337710] sd 2:0:0:0: [sdc] Unhandled error code
> > [5015740.337742] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> > [5015740.337806] end_request: I/O error, dev sdc, sector 1186573399
> > [5015740.337840] sd 2:0:0:0: [sdc] Unhandled error code
> > [5015740.337872] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> > [5015740.337936] end_request: I/O error, dev sdc, sector 404014999
> > [5015740.371191] RAID5 conf printout:
> > [5015740.371226] --- rd:4 wd:3
> > [5015740.371258] disk 0, o:0, dev:sdc1
> > [5015740.371290] disk 1, o:1, dev:sda1
> > [5015740.371322] disk 2, o:1, dev:sdb1
> > [5015740.371353] disk 3, o:1, dev:sdd1
> > [5015740.393516] RAID5 conf printout:
> > [5015740.393551] --- rd:4 wd:3
> > [5015740.393583] disk 1, o:1, dev:sda1
> > [5015740.393615] disk 2, o:1, dev:sdb1
> > [5015740.393647] disk 3, o:1, dev:sdd1
> >
> > ran: echo x > /sys/bus/scsi/devices/2\:0\:0\:0/delete
> >
> > [5016224.932073] sd 2:0:0:0: [sdc] Synchronizing SCSI cache
> > [5016224.932150] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> > [5016224.932216] sd 2:0:0:0: [sdc] Stopping disk
> > [5016224.933192] sd 2:0:0:0: [sdc] START_STOP FAILED
> > [5016224.933227] sd 2:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET
> > driverbyte=DRIVER_OK,SUGGEST_OK
> >
> > ran: echo "0 0 0" > /sys/class/scsi_host/host2/scan
> >
> > [5016463.173706] ata3: hard resetting link
> > [5016463.657520] ata3: softreset failed (device not ready)
> > [5016463.657557] ata3: failed due to HW bug, retry pmp=0
> > [5016463.821535] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > [5016463.842475] ata3.00: both IDENTIFYs aborted, assuming NODEV
> > [5016463.842492] ata3: EH complete
> >
> > To be honest, I've been expecting this, I just had no idea which drive
> > was going to fail. For the past 6-12 months I've been hearing this
> > rather loud clicking noise coming from that machine, but I could never
> > pin it down, it only happened a couple times a day (and it wasn't heads
> > parking).
> >
> > I'm tempted to try and reboot the machine, to see if the disk comes
> > back. But I'm worried the array might not come back (for whatever
> > reason).
>
> Looks like it but show smart stats as well-- they may show what/why is
> failing, if not try to run a smart test (short) and see what the error
> is, or if it passes successfully.
>
> smartctl -a /dev/disk
>
> or smartctl -d (cciss,3ware),drive -a /dev/device
>
smartctl fails. even adding -T permissive doesn't help. At this point, the
disk is completely inaccessible to the OS. Also, after removing the disk
(using the sysfs interface) it won't come back, so there is no /dev device
for it anymore, so I can't run smartctl on it again (I've lost the output
from before, which was just smartctl saying it couldn't read from the
device).
> Justin.
> --
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Thomas Fjellstrom
tfjellstrom@xxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
