Dave,
Questions inline and below.
On Mon, 18 Jun 2007, David Chinner wrote:
On Fri, Jun 15, 2007 at 04:36:07PM -0400, Justin Piszcz wrote:
Hi,
I was wondering if the XFS folks can recommend any optimizations for high
speed disk arrays using RAID5?
[sysctls snipped]
None of those options will make much difference to performance.
mkfs parameters are the big ticket item here....
There is also vm/dirty tunable in /proc.
That changes benchmark times by starting writeback earlier, but
doesn't affect actual writeback speed.
I was wondering what are some things to tune for speed? I've already
tuned the MD layer but is there anything with XFS I can also tune?
echo "Setting read-ahead to 64MB for /dev/md3"
blockdev --setra 65536 /dev/md3
This proved to give the fastest performance, I have always used 4GB then
recently 8GB of memory in the machine.
http://www.rhic.bnl.gov/hepix/talks/041019pm/schoen.pdf
See page 13.
Why so large? That's likely to cause readahead thrashing problems
under low memory....
echo "Setting stripe_cache_size to 16MB for /dev/md3"
echo 16384 > /sys/block/md3/md/stripe_cache_size
(also set max_sectors_kb) to 128K (chunk size) and disable NCQ
Why do that? You want XFS to issue large I/Os and the block layer
to split them across all the disks. i.e. you are preventing full
stripe writes from occurring by doing that.
I use a 128k stripe, what should I use for the max_sectors_kb? I read that
128kb was optimal.
Can you please comment on all of the optimizations below?
#!/bin/bash
# source profile
. /etc/profile
echo "Optimizing RAID Arrays..."
# This step must come first.
# See: http://www.3ware.com/KB/article.aspx?id=11050
echo "Setting max_sectors_kb to chunk size of RAID5 arrays..."
for i in sdc sdd sde sdf sdg sdh sdi sdj sdk sdl
do
echo "Setting /dev/$i to 128K..."
echo 128 > /sys/block/"$i"/queue/max_sectors_kb
done
echo "Setting read-ahead to 64MB for /dev/md3"
blockdev --setra 65536 /dev/md3
echo "Setting stripe_cache_size to 16MB for /dev/md3"
echo 16384 > /sys/block/md3/md/stripe_cache_size
# if you use more than the default 64kb stripe with raid5
# this feature is broken so you need to limit it to 30MB/s
# neil has a patch, not sure when it will be merged.
echo "Setting minimum and maximum resync speed to 30MB/s..."
echo 30000 > /sys/block/md0/md/sync_speed_min
echo 30000 > /sys/block/md0/md/sync_speed_max
echo 30000 > /sys/block/md1/md/sync_speed_min
echo 30000 > /sys/block/md1/md/sync_speed_max
echo 30000 > /sys/block/md2/md/sync_speed_min
echo 30000 > /sys/block/md2/md/sync_speed_max
echo 30000 > /sys/block/md3/md/sync_speed_min
echo 30000 > /sys/block/md3/md/sync_speed_max
# Disable NCQ.
echo "Disabling NCQ..."
for i in sdc sdd sde sdf sdg sdh sdi sdj sdk sdl
do
echo "Disabling NCQ on $i"
echo 1 > /sys/block/"$i"/device/queue_depth
done
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
