At long last... I've finally got my additions to Peter T. Breuer's raid1 bitmap code (fr1 v2.14, ftp://oboe.it.uc3m.es/pub/Programs/fr1-2.14.tgz) in decent shape and fairly well tested. The bitmap and asynchronous write capability are primarily useful when raid1 is employed in data replication (e.g., with a remote disk served over nbd as the secondary device). However, the bitmap is also useful for reducing resync times with ordinary (local) raid1 and raid5 arrays. The additions, above and beyond the original fr1 code, are basically: * disk storage for the bitmap (makes the bitmap persistent, so that a full resync is never needed, even after a failure or reboot of the primary server) * a kernel daemon to periodically (lazily) clear bits in the bitmap file (this reduces the number and frequency of disk writes to the bitmap file) * changing bits in the bitmap to 16-bit counters (this ensures that a bit won't be cleared prematurely when there are multiple outstanding I/Os to a block, which could result in data loss on the backup system if a failure coincided) * allowing the bitmap to be rescaled -- i.e., changing the amount of data that each bit represents (currently, the 2.6 code can handle a chunk size up to 64k) * modifying the code so that it can be more easily leveraged by other raid drivers (namely raid5) I originally wrote this code for 2.4 (I have a patch vs. 2.4.19 SuSE kernel, if anyone is interested) and recently ported it to 2.6. The code currently allows the use of a bitmap with raid1 arrays (this could also be extended to raid5, but I haven't put the bitmap calls into raid5.c -- if anyone would like to do that, I'd love to see it happen -- it shouldn't be hard if you're familiar with raid5 (...I'm not :/). I have also modified Neil's mdadm tool to allow it to configure the additional bitmap and async parameters. The attached patch is against the 1.2 mdadm release. Briefly, the new options are: Creation: mdadm -C /dev/md0 -l 1 --persistent --bitmap=/tmp/bitmap_md0_file,65536,15 --async=512 -n 2 /dev/xxx /dev/yyy This creates a raid1 array with: two disks a persistent superblock asynchronous writes enabled (maximum of 512 outstanding writes) bitmap enabled (using the file /tmp/bitmap_md0_file) a bitmap chunksize of 64k (bitmap chunksize determines how much data each bitmap bit represents) the bitmap daemon set to wake up every 15 seconds to clear bits in the bitmap file (if needed) /dev/xxx as the primary disk /dev/yyy as the backup disk (when asynchronous writes are enabled, the second disk in the array is labelled as a "backup", indicating that it is remote, and thus no reads will be issued to the device) Assembling: mdadm -A /dev/md0 --bitmap=/tmp/bitmap_md0_file /dev/xxx /dev/yyy This assembles an existing array and configures it to use a bitmap file. The bitmap file pathname is not stored in the array superblock, and so must be specified every time the array is assembled. Details: mdadm -D /dev/md0 This will display information about /dev/md0, including some additional information about the bitmap and async parameters. I've also added some information to the /proc/mdstat file: # cat /proc/mdstat Personalities : [raid1] md1 : active raid1 loop0[0] loop1[1](B) 39936 blocks [2/2] [UU] async: 0/256 outstanding writes bitmap: 1/1 pages (15 cached) [64KB], 64KB chunk, file: /tmp/bitmap_md1 unused devices: <none> Finally, the patches are available here: kernel patch vs. 2.6.0-test3: http://parisc-linux.org/~jejb/md_bitmap/md_bitmap_2_28_2_6_0_TEST3.diff mdadm patch vs. 1.2.0: http://parisc-linux.org/~jejb/md_bitmap/mdadm_1_2_0.diff So if you have any interest, please review, test, ask questions, etc. (And if you're really a glutton, the gory details of the design and implementation can be found in Section 3 of my OLS Paper: http://archive.linuxsymposium.org/ols2003/Proceedings/All-Reprints/Reprint-Clements-OLS2003.pdf) Thanks, Paul - To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
