On Thu, 30 Mar 2017 18:06:47 +0200, Tanu Kaskinen wrote: > > On Wed, 2017-03-29 at 16:51 +0200, Takashi Iwai wrote: > > On Wed, 29 Mar 2017 16:40:28 +0200, > > Tanu Kaskinen wrote: > > > > > > On Wed, 2017-03-29 at 15:26 +0200, Takashi Iwai wrote: > > > > On Wed, 29 Mar 2017 15:14:19 +0200, > > > > Tanu Kaskinen wrote: > > > > > > > > > > On Wed, 2017-03-29 at 15:06 +0200, Takashi Iwai wrote: > > > > > > On Wed, 29 Mar 2017 14:59:45 +0200, > > > > > > Tanu Kaskinen wrote: > > > > > > > > > > > > > > On Wed, 2017-03-29 at 07:21 +0200, Takashi Iwai wrote: > > > > > > > > Does PA really need to start streaming at its invocation time? > > > > > > > > The crash happens when PA gets started via desktop autostart, and at > > > > > > > > this moment, the HDMI graphics state is possible disconnected before > > > > > > > > xrandr setup. The HDMI connection state should have been informed / > > > > > > > > notified to PA via the jack interface, so it should be possible to > > > > > > > > judge beforehand. > > > > > > > > > > > > > > > > Or it might be something wrong in the driver side regarding the jack > > > > > > > > state processing? > > > > > > > > > > > > > > I had a closer look at the PA log that was posted earlier. It looks > > > > > > > like the device numbering is non-standard. Trying to open any of the > > > > > > > hdmi:1,x devices fails. hw:1 can be opened, and pulseaudio assumes that > > > > > > > it's an analog stereo device. Jack detection isn't going to work in > > > > > > > this situation, because pulseaudio doesn't know that it should be > > > > > > > looking at the hdmi jacks. > > > > > > > > > > > > > > Can the driver be fixed to use the standard HDMI device numbers? > > > > > > > > > > > > Hmm, it might be the missing hdmi PCM definition? > > > > > > > > > > > > The latest alsa-lib git already contains the card config for HDMI LPE > > > > > > audio, and this might help. (Though, I thought I still saw the same > > > > > > PA problem even with the card config. Unfortunately I can't access > > > > > > the box with the DP audio right now, so others may help more quickly > > > > > > than me...) > > > > > > > > > > > > Can anyone confirm that you have the latest alsa-lib git installed and > > > > > > whether the PA issue is fixed or not? > > > > > > > > > > If the alsa-lib configuration just maps hdmi:1,0 to hw:1,0, then I > > > > > would expect this problem to persist. If hw:1,0 can be opened, > > > > > pulseaudio will think that there's an analog stereo output. If hdmi:1,0 > > > > > works too, then pulseaudio will think that there are two separate > > > > > outputs, and if the hdmi jack state says that hdmi is not available, > > > > > pulseaudio will use what it thinks is an analog output. > > > > > > > > Aha, that explains. > > > > > > > > > If it's not possible to change the device numbering in the driver, this > > > > > will have to be worked around in pulseaudio somehow (pulseaudio > > > > > shouldn't try to use hw:1,0 on this hardware). > > > > > > > > Well, it's not impossible to change in the driver side, but I hesitate > > > > to do so, since it's not right, IMO. > > > > > > > > In general, the PCM device#0 isn't always for an analog output, > > > > although it's de facto standard, as most boards have both analog and > > > > HDMI/DP. For HD-audio, we even kept the constant PCM dev# even if no > > > > analog output is present; but it's just to make the configuration > > > > easier, and it doesn't mean that PCM dev#0 is for the analog I/O. > > > > > > I agree, it's not good to assume that hw:x,0 is always analog stereo > > > output. Pulseaudio should fall back to hw: only if nothing else works. > > > > > > The jack name problem is easily solved in pulseaudio, but there's one > > > more problem related to the device numbers: pulseaudio needs to know > > > which ELD element corresponds to which PCM device. Currently the > > > mapping is hardcoded: hdmi:x,0 is expected to always correspond to the > > > ELD element of device 3. Is there any way pulseaudio could query the > > > mapping instead of hardcoding it? > > > > Oh that's ugly. This mess comes from the HD-audio configuration, my > > bad. > > > > The ELD index number is aligned with the PCM device number (in a way > > of hw:x,y), thus it's 3 for HD-audio. It's used for HDMI/DP jack, > > too. > > > > I guess you can get this from snd_pcm_info() => > > snd_pcm_info_get_device() call for the opened stream? > > The usual plugins should return the slsave pcm info, so even for > > hdmi:x,y, it should reach to the underlying hardware PCM. > > That sounds workable. Unless someone else wants to help with this, I'll > work on the PulseAudio changes. Please go ahead. I believe fixing this in PA is the best option. thanks, Takashi > I created a bug report here: > https://bugs.freedesktop.org/show_bug.cgi?id=100488 > > -- > Tanu > > https://www.patreon.com/tanuk >
