I submitted a ticket and patch that fixes these build errors - tested on a Beagleboard (OMAP3) with Linaro ARM Linux image. I did not test on other platforms due to this being specific to ARM. Thanks again for your help Arun! http://pulseaudio.org/ticket/914 Kurt Taylor (irc krtaylor) On 17 February 2011 12:25, Kurt Taylor <kurt.taylor at linaro.org> wrote: > Here is the output of gcc -dumpspecs > > http://pastebin.com/Z2ZDVrbc > > Kurt Taylor (irc krtaylor) > > > > On 17 February 2011 12:10, Kurt Taylor <kurt.taylor at linaro.org> wrote: > >> Thanks for your help Arun. I was finally able to come back to this >> problem. Here is the last lines of a make on a clean git clone showing the >> errors on the beagleboard (linaro ALIP). >> >> Adding "ite" before the addcs did not build, adding itt built and ran, but >> unloaded alsa module. >> >> http://pastebin.com/Lqw0rEh9 >> >> Kurt Taylor (irc krtaylor) >> >> >> >> On 14 February 2011 08:45, Arun Raghavan <arun.raghavan at collabora.co.uk>wrote: >> >>> On Mon, 2011-02-07 at 12:52 -0600, Kurt Taylor wrote: >>> > >>> > I am seeing the following when trying to build pulseaudio on an >>> > ARM-based Beagleboard (OMAP3): >>> > >>> > CC libpulsecore_1.0_la-svolume_arm.lo >>> > ../libtool: line 975: warning: setlocale: LC_MESSAGES: cannot change >>> > locale (en_GB.utf8) >>> > {standard input}: Assembler messages: >>> > {standard input}:82: Error: thumb conditional instruction should be in >>> > IT block -- `addcs r0,r8' >>> > {standard input}:83: Error: thumb conditional instruction should be in >>> > IT block -- `movcs r6,r0' >>> > {standard input}:98: Error: thumb conditional instruction should be in >>> > IT block -- `addcs r0,r8' >>> > {standard input}:99: Error: thumb conditional instruction should be in >>> > IT block -- `movcs r6,r0' >>> > {standard input}:119: Error: thumb conditional instruction should be >>> > in IT block -- `addcs r0,r8' >>> > {standard input}:120: Error: thumb conditional instruction should be >>> > in IT block -- `movcs r6,r0' >>> > >>> > I am using the normal build (bootstrap.sh, configure, make) on Linaro >>> > ALIP on the Beagleboard. The build worked fine on a Pandaboard with >>> > Ubuntu 10.10. It looks like something is different and not being >>> > detected via bootstrap/configure on ALIP. >>> > >>> > I believe configure has identified the architecture correctly. Also, I >>> > have searched and seen commits in the pulseaudio/ubuntu maillist >>> > archive for adding "-Wa, -mimplicit-it=thumb". I have added this to >>> > CFLAGS without success. >>> > >>> > Any thoughts on what else I could try? >>> >>> What CFLAGS are you using? This should only turn up if you're compiling >>> that assembly in Thumb-2 mode. >>> >>> I'm not sure if it would actually be desirable to compile in Thumb-2 >>> mode for the OMAP3, but the correct fix for this would probably be to >>> add an "ite cs" before the addcs in svolume_arm.c. Could you test this >>> out (or let me know if you'd like a patch that does this)? >>> >>> -- Arun >>> >>> _______________________________________________ >>> pulseaudio-discuss mailing list >>> pulseaudio-discuss at mail.0pointer.de >>> https://tango.0pointer.de/mailman/listinfo/pulseaudio-discuss >>> >> >> > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.freedesktop.org/archives/pulseaudio-discuss/attachments/20110218/6a3f41b1/attachment.htm>
