Some MeeGoPad top-set boxes have an ANX7428 Type-C Switch for USB3.1 Gen 1 and DisplayPort over Type-C alternate mode support. The ANX7428 has a microcontroller which takes care of the PD negotiation and automatically sets the builtin Crosspoint Switch to send the right signal to the 4 highspeed pairs of the Type-C connector. It also takes care of HPD and AUX channel routing for DP alternate mode. IOW the ANX7428 operates fully autonomous and to the x5-Z8350 SoC things look like there simple is a USB-3 Type-A connector and a separate DisplayPort connector. Except that the BIOS does not power on the ANX7428 at boot (meh). Add a driver to power on the ANX7428. This driver is added under drivers/platform/x86 rather than under drivers/usb/typec for 2 reasons: 1. This driver is specifically written to work with how the ANX7428 is described in the ACPI tables of the MeeGoPad x86 (Cherry Trail) devices. 2. This driver only powers on the ANX7428 and does not do anything wrt its Type-C functionality. It should be possible to tell the controller which data- and/or power-role to negotiate and to swap the role(s) after negotiation but the MeeGoPad top-set boxes always draw their power from a separate power-connector and they only support USB host-mode. So this functionality is unnecessary and due to lack of documentation this is tricky to support. Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- Changes in v2: - Switch to read_poll_timeout() for waiting for the microcontroller to boot - Address a few other small review remarks from Andy --- drivers/platform/x86/Kconfig | 11 ++ drivers/platform/x86/Makefile | 3 + drivers/platform/x86/meegopad_anx7428.c | 148 ++++++++++++++++++++++++ 3 files changed, 162 insertions(+) create mode 100644 drivers/platform/x86/meegopad_anx7428.c diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index e5601d8fba68..0ec952b5d03e 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -666,6 +666,17 @@ config ACPI_QUICKSTART To compile this driver as a module, choose M here: the module will be called quickstart. +config MEEGOPAD_ANX7428 + tristate "MeeGoPad ANX7428 Type-C Switch" + depends on ACPI && GPIOLIB && I2C + help + Some MeeGoPad top-set boxes have an ANX7428 Type-C Switch for + USB3.1 Gen 1 and DisplayPort over Type-C alternate mode support. + + This driver takes care of powering on the ANX7428 on supported + MeeGoPad top-set boxes. After this the ANX7428 takes care of Type-C + connector orientation and PD alternate mode switching autonomously. + config MSI_EC tristate "MSI EC Extras" depends on ACPI diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile index cf3032e4e27f..e1b142947067 100644 --- a/drivers/platform/x86/Makefile +++ b/drivers/platform/x86/Makefile @@ -75,6 +75,9 @@ obj-y += intel/ # Microsoft obj-$(CONFIG_ACPI_QUICKSTART) += quickstart.o +# MeeGoPad +obj-$(CONFIG_MEEGOPAD_ANX7428) += meegopad_anx7428.o + # MSI obj-$(CONFIG_MSI_EC) += msi-ec.o obj-$(CONFIG_MSI_LAPTOP) += msi-laptop.o diff --git a/drivers/platform/x86/meegopad_anx7428.c b/drivers/platform/x86/meegopad_anx7428.c new file mode 100644 index 000000000000..8c025e39f3f1 --- /dev/null +++ b/drivers/platform/x86/meegopad_anx7428.c @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Driver to power on the Analogix ANX7428 USB Type-C crosspoint switch + * on MeeGoPad top-set boxes. + * + * The MeeGoPad T8 and T9 are Cherry Trail top-set boxes which + * use an ANX7428 to provide a Type-C port with USB3.1 Gen 1 and + * DisplayPort over Type-C alternate mode support. + * + * The ANX7428 has a microcontroller which takes care of the PD + * negotiation and automatically sets the builtin Crosspoint Switch + * to send the right signal to the 4 highspeed pairs of the Type-C + * connector. It also takes care of HPD and AUX channel routing for + * DP alternate mode. + * + * IOW the ANX7428 operates fully autonomous and to the x5-Z8350 SoC + * things look like there simple is a USB-3 Type-A connector and a + * separate DisplayPort connector. Except that the BIOS does not + * power on the ANX7428 at boot. This driver takes care of powering + * on the ANX7428. + * + * It should be possible to tell the micro-controller which data- and/or + * power-role to negotiate and to swap the role(s) after negotiation + * but the MeeGoPad top-set boxes always draw their power from a separate + * power-connector and they only support USB host-mode. So this functionality + * is unnecessary and due to lack of documentation this is tricky to support. + * + * For a more complete ANX7428 driver see drivers/usb/misc/anx7418/ of + * the LineageOS kernel for the LG G5 (International) aka the LG H850: + * https://github.com/LineageOS/android_kernel_lge_msm8996/ + * + * (C) Copyright 2024 Hans de Goede <hansg@xxxxxxxxxx> + */ + +#include <linux/acpi.h> +#include <linux/bits.h> +#include <linux/delay.h> +#include <linux/dmi.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/iopoll.h> +#include <linux/module.h> + +/* Register addresses and fields */ +#define VENDOR_ID 0x00 +#define DEVICE_ID 0x02 + +#define TX_STATUS 0x16 +#define STATUS_SUCCESS BIT(0) +#define STATUS_ERROR BIT(1) +#define OCM_STARTUP BIT(7) + +static bool force; +module_param(force, bool, 0444); +MODULE_PARM_DESC(force, "Force the driver to probe on unknown boards"); + +static const struct acpi_gpio_params enable_gpio = { 0, 0, false }; +static const struct acpi_gpio_params reset_gpio = { 1, 0, true }; + +static const struct acpi_gpio_mapping meegopad_anx7428_gpios[] = { + { "enable-gpios", &enable_gpio, 1 }, + { "reset-gpios", &reset_gpio, 1 }, + { } +}; + +static const struct dmi_system_id meegopad_anx7428_ids[] = { + { + /* Meegopad T08 */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Default string"), + DMI_MATCH(DMI_PRODUCT_NAME, "Default string"), + DMI_MATCH(DMI_BOARD_NAME, "T3 MRD"), + DMI_MATCH(DMI_BOARD_VERSION, "V1.1"), + }, + }, + { } +}; + +static int anx7428_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct gpio_desc *gpio; + int ret, val; + + if (!dmi_check_system(meegopad_anx7428_ids) && !force) { + dev_warn(dev, "Not probing unknown board, pass meegopad_anx7428.force=1 to probe"); + return -ENODEV; + } + + ret = devm_acpi_dev_add_driver_gpios(dev, meegopad_anx7428_gpios); + if (ret) + return ret; + + /* + * Set GPIOs to desired values while getting them, they are not needed + * afterwards. Ordering and delays come from android_kernel_lge_msm8996. + */ + gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH); + if (IS_ERR(gpio)) + return dev_err_probe(dev, PTR_ERR(gpio), "getting enable GPIO\n"); + + fsleep(10000); + + gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(gpio)) + return dev_err_probe(dev, PTR_ERR(gpio), "getting reset GPIO\n"); + + /* Wait for the OCM (On Chip Microcontroller) to start */ + ret = read_poll_timeout(i2c_smbus_read_byte_data, val, + val >= 0 && (val & OCM_STARTUP), + 5000, 50000, true, client, TX_STATUS); + if (ret) + return dev_err_probe(dev, ret, + "On Chip Microcontroller did not start, status: 0x%02x\n", + val); + + ret = i2c_smbus_read_word_data(client, VENDOR_ID); + if (ret < 0) + return dev_err_probe(dev, ret, "reading vendor-id register\n"); + val = ret; + + ret = i2c_smbus_read_word_data(client, DEVICE_ID); + if (ret < 0) + return dev_err_probe(dev, ret, "reading device-id register\n"); + + dev_dbg(dev, "Powered on ANX7428 id %04x:%04x\n", val, ret); + return 0; +} + +static const struct acpi_device_id anx7428_acpi_match[] = { + { "ANXO7418" }, /* ACPI says 7418 (max 2 DP lanes version) but HW is 7428 */ + { } +}; +MODULE_DEVICE_TABLE(acpi, anx7428_acpi_match); + +static struct i2c_driver anx7428_driver = { + .driver = { + .name = "meegopad_anx7428", + .acpi_match_table = anx7428_acpi_match, + }, + .probe = anx7428_probe, +}; + +module_i2c_driver(anx7428_driver); + +MODULE_AUTHOR("Hans de Goede <hansg@xxxxxxxxxx>"); +MODULE_DESCRIPTION("MeeGoPad ANX7428 driver"); +MODULE_LICENSE("GPL"); -- 2.44.0
