Ilpo,
Thanks a lot for the review.
On Wed, Feb 14, 2024 at 7:14 PM Ilpo Järvinen
<ilpo.jarvinen@xxxxxxxxxxxxxxx> wrote:
>
> On Wed, 14 Feb 2024, Vishnu Sankar wrote:
>
> Thanks for doing this, it's major improvement to readability already as
> is, and even more of after the second patch!!
>
> > Add a thermal_read_mode_check helper function to make the code
>
> thermal_read_mode_check()
>
> remove "function" as it's obvious.
Acked
>
> > simpler during init.
> > This helps particularly when the new TPEC_12 mode is added in
> > the next patch.
>
> Flow the paragraph normally without the premature line break.
Acked.
>
> > Suggested-by: Ilpo Jarvinen <ilpo.jarvinen@xxxxxxxxx>
>
> This is not my email address, please use
>
> Suggested-by: Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx>
Sorry for this.
Will correct email address.
>
> > Signed-off-by: Vishnu Sankar <vishnuocv@xxxxxxxxx>
> > ---
> > drivers/platform/x86/thinkpad_acpi.c | 136 +++++++++++++--------------
> > 1 file changed, 66 insertions(+), 70 deletions(-)
> >
> > diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
> > index c4895e9bc714..2428c8bd0fa2 100644
> > --- a/drivers/platform/x86/thinkpad_acpi.c
> > +++ b/drivers/platform/x86/thinkpad_acpi.c
> > @@ -6147,6 +6147,71 @@ struct ibm_thermal_sensors_struct {
> > static enum thermal_access_mode thermal_read_mode;
> > static bool thermal_use_labels;
> >
> > +/* Function to check thermal read mode */
> > +static enum thermal_access_mode thermal_read_mode_check(void)
> > +{
> > + u8 t, ta1, ta2, ver = 0;
> > + int i;
> > +
> > + if (thinkpad_id.ec_model) {
> > + /*
> > + * Direct EC access mode: sensors at registers
> > + * 0x78-0x7F, 0xC0-0xC7. Registers return 0x00 for
>
> Remove the double space, one is enough in kernel comments.
Acked
>
> > + * non-implemented, thermal sensors return 0x80 when
> > + * not available
>
> Add the missing . please.
>
> Perhaps add a empty line here to make this two paragraphs.
Acked
>
> > + * The above rule is unfortunately flawed. This has been seen with
> > + * 0xC2 (power supply ID) causing thermal control problems.
> > + * The EC version can be determined by offset 0xEF and at least for
> > + * version 3 the Lenovo firmware team confirmed that registers 0xC0-0xC7
> > + * are not thermal registers.
> > + */
>
> While the patch touches this, this entire comment should be reflowed
> properly for 80 columns.
Will try re-writing the comments block for 80 columns.
>
> > + if (!acpi_ec_read(TP_EC_FUNCREV, &ver))
> > + pr_warn("Thinkpad ACPI EC unable to access EC version\n");
> > +
> > + ta1 = ta2 = 0;
> > + for (i = 0; i < 8; i++) {
> > + if (acpi_ec_read(TP_EC_THERMAL_TMP0 + i, &t)) {
> > + ta1 |= t;
> > + } else {
> > + ta1 = 0;
> > + break;
> > + }
> > + if (ver < 3) {
> > + if (acpi_ec_read(TP_EC_THERMAL_TMP8 + i, &t)) {
> > + ta2 |= t;
> > + } else {
> > + ta1 = 0;
> > + break;
> > + }
> > + }
> > + }
> > +
> > + if (ta1 == 0) {
> > + pr_err("ThinkPad ACPI EC access misbehaving, disabling thermal sensors access\n");
> > + return TPACPI_THERMAL_NONE;
> > + }
> > +
> > + if (ver >= 3) {
> > + thermal_use_labels = true;
> > + return TPACPI_THERMAL_TPEC_8;
> > + }
> > +
> > + return (ta2 != 0) ? TPACPI_THERMAL_TPEC_16 : TPACPI_THERMAL_TPEC_8;
> > + }
> > +
> > + if (acpi_evalf(ec_handle, NULL, "TMP7", "qv")) {
> > + if (tpacpi_is_ibm() &&
> > + acpi_evalf(ec_handle, NULL, "UPDT", "qv"))
>
> Single line and keep the braces please (I know it will go >80 chars but no
> important info is lost).
Acked.
Will change this.
>
> > + /* 600e/x, 770e, 770x */
> > + return TPACPI_THERMAL_ACPI_UPDT;
> > + /* IBM/LENOVO DSDT EC.TMPx access, max 8 sensors */
> > + return TPACPI_THERMAL_ACPI_TMP07;
> > + }
> > +
> > + /* temperatures not supported on 570, G4x, R30, R31, R32 */
> > + return TPACPI_THERMAL_NONE;
> > +}
> > +
> > /* idx is zero-based */
> > static int thermal_get_sensor(int idx, s32 *value)
> > {
> > @@ -6375,78 +6440,9 @@ static const struct attribute_group temp_label_attr_group = {
> >
> > static int __init thermal_init(struct ibm_init_struct *iibm)
> > {
> > - u8 t, ta1, ta2, ver = 0;
> > - int i;
> > - int acpi_tmp7;
> > -
> > vdbg_printk(TPACPI_DBG_INIT, "initializing thermal subdriver\n");
> >
> > - acpi_tmp7 = acpi_evalf(ec_handle, NULL, "TMP7", "qv");
> > -
> > - if (thinkpad_id.ec_model) {
> > - /*
> > - * Direct EC access mode: sensors at registers
> > - * 0x78-0x7F, 0xC0-0xC7. Registers return 0x00 for
> > - * non-implemented, thermal sensors return 0x80 when
> > - * not available
> > - * The above rule is unfortunately flawed. This has been seen with
> > - * 0xC2 (power supply ID) causing thermal control problems.
> > - * The EC version can be determined by offset 0xEF and at least for
> > - * version 3 the Lenovo firmware team confirmed that registers 0xC0-0xC7
> > - * are not thermal registers.
> > - */
> > - if (!acpi_ec_read(TP_EC_FUNCREV, &ver))
> > - pr_warn("Thinkpad ACPI EC unable to access EC version\n");
> > -
> > - ta1 = ta2 = 0;
> > - for (i = 0; i < 8; i++) {
> > - if (acpi_ec_read(TP_EC_THERMAL_TMP0 + i, &t)) {
> > - ta1 |= t;
> > - } else {
> > - ta1 = 0;
> > - break;
> > - }
> > - if (ver < 3) {
> > - if (acpi_ec_read(TP_EC_THERMAL_TMP8 + i, &t)) {
> > - ta2 |= t;
> > - } else {
> > - ta1 = 0;
> > - break;
> > - }
> > - }
> > - }
> > - if (ta1 == 0) {
> > - /* This is sheer paranoia, but we handle it anyway */
> > - if (acpi_tmp7) {
> > - pr_err("ThinkPad ACPI EC access misbehaving, falling back to ACPI TMPx access mode\n");
> > - thermal_read_mode = TPACPI_THERMAL_ACPI_TMP07;
>
> Eh, where did this go in the new helper?
Sorry.
This will be added in V2.
>
> --
> i.
>
> > - } else {
> > - pr_err("ThinkPad ACPI EC access misbehaving, disabling thermal sensors access\n");
> > - thermal_read_mode = TPACPI_THERMAL_NONE;
> > - }
> > - } else {
> > - if (ver >= 3) {
> > - thermal_read_mode = TPACPI_THERMAL_TPEC_8;
> > - thermal_use_labels = true;
> > - } else {
> > - thermal_read_mode =
> > - (ta2 != 0) ?
> > - TPACPI_THERMAL_TPEC_16 : TPACPI_THERMAL_TPEC_8;
> > - }
> > - }
> > - } else if (acpi_tmp7) {
> > - if (tpacpi_is_ibm() &&
> > - acpi_evalf(ec_handle, NULL, "UPDT", "qv")) {
> > - /* 600e/x, 770e, 770x */
> > - thermal_read_mode = TPACPI_THERMAL_ACPI_UPDT;
> > - } else {
> > - /* IBM/LENOVO DSDT EC.TMPx access, max 8 sensors */
> > - thermal_read_mode = TPACPI_THERMAL_ACPI_TMP07;
> > - }
> > - } else {
> > - /* temperatures not supported on 570, G4x, R30, R31, R32 */
> > - thermal_read_mode = TPACPI_THERMAL_NONE;
> > - }
> > + thermal_read_mode = thermal_read_mode_check();
> >
> > vdbg_printk(TPACPI_DBG_INIT, "thermal is %s, mode %d\n",
> > str_supported(thermal_read_mode != TPACPI_THERMAL_NONE),
> >
--
Regards,
Vishnu Sankar
+817015150407 (Japan)
