Add description for new attributes added for rack manager switch and NG800 family systems. Attributes related to power converter board: - reset_pwr_converter_fail; - pwr_converter_prog_en; Attributes related to External Root of Trust (EROT) devices recovery: - erot1_ap_reset; - erot2_ap_reset; - erot1_recovery; - erot2_recovery; - erot1_reset; - erot2_reset; - erot1_wp; - erot2_wp; - spi_chnl_select; Attributes related to clock board failures and recovery: - clk_brd1_boot_fail; - clk_brd2_boot_fail; - clk_brd_fail; - clk_brd_prog_en; Attributes related to power failures: - reset_ac_ok_fail; - asic_pg_fail; Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxx> Reviewed-by: Michael Shych <michaelsh@xxxxxxxxxx> --- .../ABI/stable/sysfs-driver-mlxreg-io | 122 +++++++++++++++++- 1 file changed, 121 insertions(+), 1 deletion(-) diff --git a/Documentation/ABI/stable/sysfs-driver-mlxreg-io b/Documentation/ABI/stable/sysfs-driver-mlxreg-io index af0cbf143c48..60953903d007 100644 --- a/Documentation/ABI/stable/sysfs-driver-mlxreg-io +++ b/Documentation/ABI/stable/sysfs-driver-mlxreg-io @@ -522,7 +522,6 @@ Description: These files allow to each of ASICs by writing 1. The files are write only. - What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/comm_chnl_ready Date: July 2022 KernelVersion: 5.20 @@ -542,3 +541,124 @@ Description: The file indicates COME module hardware configuration. The purpose is to expose some minor BOM changes for the same system SKU. The file is read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_pwr_converter_fail +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: This file shows the system reset cause due to power converter + devices failure. + Value 1 in file means this is reset cause, 0 - otherwise. + + The file is read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_ap_reset +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_ap_reset +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: These files aim to monitor the status of the External Root of Trust (EROT) + processor's RESET output to the Application Processor (AP). + By reading this file, could be determined if the EROT has invalidated or + revoked AP Firmware, at which point it will hold the AP in RESET until a + valid firmware is loaded. This protects the AP from running an + unauthorized firmware. In the normal flow, the AP reset should be released + after the EROT validates the integrity of the FW, and it should be done so + as quickly as possible so that the AP boots before the CPU starts to + communicate to each ASIC. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_recovery +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_recovery +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_reset +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_reset +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: These files aim to perform External Root of Trust (EROT) recovery + sequence after EROT device failure. + These EROT devices protect ASICs from unauthorized access and in normal + flow their reset should be released with system power – earliest power + up stage, so that EROTs can begin boot and authentication process before + CPU starts to communicate to ASICs. + Issuing a reset to the EROT while asserting the recovery signal will cause + the EROT Application Processor to enter recovery mode so that the EROT FW + can be updated/recovered. + For reset/recovery the related file should be toggled by 1/0. + + The files are read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_wp +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_wp +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: These files allow access to External Root of Trust (EROT) for reset + and recovery sequence after EROT device failure. + Default is 0 (programming disabled). + If the system is in locked-down mode writing this file will not be allowed. + + The files are read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/spi_chnl_select +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: This file allows SPI chip selection for External Root of Trust (EROT) + device Out-of-Band recovery. + File can be written with 0 or with 1. It selects which EROT can be accessed + through SPI device. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/asic_pg_fail +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak vadimp@xxxxxxxxxx +Description: This file shows ASIC Power Good status. + Value 1 in file means ASIC Power Good failed, 0 - otherwise. + + The file is read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd1_boot_fail +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd2_boot_fail +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd_fail +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak vadimp@xxxxxxxxxx +Description: These files are related to clock boards status in system. + - clk_brd1_boot_fail: warning about 1-st clock board failed to boot from CI. + - clk_brd2_boot_fail: warning about 2-nd clock board failed to boot from CI. + - clk_brd_fail: error about common clock board boot failure. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd_prog_en +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: This file enables programming of clock boards. + Default is 0 (programming disabled). + If the system is in locked-down mode writing this file will not be allowed. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_converter_prog_en +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: This file enables programming of power converters. + Default is 0 (programming disabled). + If the system is in locked-down mode writing this file will not be allowed. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_ac_ok_fail +Date: February 2023 +KernelVersion: 6.3 +Contact: Vadim Pasternak <vadimp@xxxxxxxxxx> +Description: This file shows the system reset cause due to AC power failure. + Value 1 in file means this is reset cause, 0 - otherwise. + + The file is read only. -- 2.20.1
