From: Yauhen Kharuzhy <jekhor@xxxxxxxxx>
Add a "linux,pump-express-vbus-max" property which indicates if the Pump
Express+ protocol should be used to increase the charging protocol.
If this new property is set and a DCP charger is detected then request
a higher charging voltage through the Pump Express+ protocol.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Changes by Hans de Goede:
- Port to my bq25890 patch-series + various cleanups
- Make behavior configurable through a new "linux,pump-express-vbus-max"
device-property
- Sleep 1 second before re-checking the Vbus voltage after requesting
it to be raised, to ensure that the ADC has time to sampled the new Vbus
- Add VBUSV bq25890_tables[] entry and use it in bq25890_get_vbus_voltage()
- Tweak commit message
Signed-off-by: Yauhen Kharuzhy <jekhor@xxxxxxxxx>
Co-developed-by: Hans de Goede <hdegoede@xxxxxxxxxx>
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
Changes in v3:
- Re-indent bq25890_tables to make checkpatch happy
- Add _uV postfix to PUMP_EXPRESS_VBUS_MARGIN
- Use regmap_field_read_poll_timeout() to wait for F_PUMPX_UP bit to clear
- Don't error check device_property_read_u32() call for optional prop
Changes in v2:
- New patch in v2 of this series, also see "Changes by Hans de Goede"
---
drivers/power/supply/bq25890_charger.c | 92 +++++++++++++++++++++++---
1 file changed, 84 insertions(+), 8 deletions(-)
diff --git a/drivers/power/supply/bq25890_charger.c b/drivers/power/supply/bq25890_charger.c
index 3de72f0fbf3e..179abed92f9b 100644
--- a/drivers/power/supply/bq25890_charger.c
+++ b/drivers/power/supply/bq25890_charger.c
@@ -27,6 +27,10 @@
#define BQ25895_ID 7
#define BQ25896_ID 0
+#define PUMP_EXPRESS_START_DELAY (5 * HZ)
+#define PUMP_EXPRESS_MAX_TRIES 6
+#define PUMP_EXPRESS_VBUS_MARGIN_uV 1000000
+
enum bq25890_chip_version {
BQ25890,
BQ25892,
@@ -107,6 +111,7 @@ struct bq25890_device {
struct usb_phy *usb_phy;
struct notifier_block usb_nb;
struct work_struct usb_work;
+ struct delayed_work pump_express_work;
unsigned long usb_event;
struct regmap *rmap;
@@ -114,6 +119,7 @@ struct bq25890_device {
bool skip_reset;
bool read_back_init_data;
+ u32 pump_express_vbus_max;
enum bq25890_chip_version chip_version;
struct bq25890_init_data init_data;
struct bq25890_state state;
@@ -265,6 +271,7 @@ enum bq25890_table_ids {
TBL_VREG,
TBL_BOOSTV,
TBL_SYSVMIN,
+ TBL_VBUSV,
TBL_VBATCOMP,
TBL_RBATCOMP,
@@ -325,14 +332,15 @@ static const union {
} bq25890_tables[] = {
/* range tables */
/* TODO: BQ25896 has max ICHG 3008 mA */
- [TBL_ICHG] = { .rt = {0, 5056000, 64000} }, /* uA */
- [TBL_ITERM] = { .rt = {64000, 1024000, 64000} }, /* uA */
- [TBL_IINLIM] = { .rt = {100000, 3250000, 50000} }, /* uA */
- [TBL_VREG] = { .rt = {3840000, 4608000, 16000} }, /* uV */
- [TBL_BOOSTV] = { .rt = {4550000, 5510000, 64000} }, /* uV */
- [TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} }, /* uV */
- [TBL_VBATCOMP] ={ .rt = {0, 224000, 32000} }, /* uV */
- [TBL_RBATCOMP] ={ .rt = {0, 140000, 20000} }, /* uOhm */
+ [TBL_ICHG] = { .rt = {0, 5056000, 64000} }, /* uA */
+ [TBL_ITERM] = { .rt = {64000, 1024000, 64000} }, /* uA */
+ [TBL_IINLIM] = { .rt = {100000, 3250000, 50000} }, /* uA */
+ [TBL_VREG] = { .rt = {3840000, 4608000, 16000} }, /* uV */
+ [TBL_BOOSTV] = { .rt = {4550000, 5510000, 64000} }, /* uV */
+ [TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} }, /* uV */
+ [TBL_VBUSV] = { .rt = {2600000, 15300000, 100000} }, /* uV */
+ [TBL_VBATCOMP] = { .rt = {0, 224000, 32000} }, /* uV */
+ [TBL_RBATCOMP] = { .rt = {0, 140000, 20000} }, /* uOhm */
/* lookup tables */
[TBL_TREG] = { .lt = {bq25890_treg_tbl, BQ25890_TREG_TBL_SIZE} },
@@ -435,6 +443,17 @@ static bool bq25890_is_adc_property(enum power_supply_property psp)
static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq);
+static int bq25890_get_vbus_voltage(struct bq25890_device *bq)
+{
+ int ret;
+
+ ret = bq25890_field_read(bq, F_VBUSV);
+ if (ret < 0)
+ return ret;
+
+ return bq25890_find_val(ret, TBL_VBUSV);
+}
+
static int bq25890_power_supply_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
@@ -613,6 +632,11 @@ static void bq25890_charger_external_power_changed(struct power_supply *psy)
switch (val.intval) {
case POWER_SUPPLY_USB_TYPE_DCP:
input_current_limit = bq25890_find_idx(2000000, TBL_IINLIM);
+ if (bq->pump_express_vbus_max) {
+ queue_delayed_work(system_power_efficient_wq,
+ &bq->pump_express_work,
+ PUMP_EXPRESS_START_DELAY);
+ }
break;
case POWER_SUPPLY_USB_TYPE_CDP:
case POWER_SUPPLY_USB_TYPE_ACA:
@@ -878,6 +902,53 @@ static int bq25890_set_otg_cfg(struct bq25890_device *bq, u8 val)
return ret;
}
+static void bq25890_pump_express_work(struct work_struct *data)
+{
+ struct bq25890_device *bq =
+ container_of(data, struct bq25890_device, pump_express_work.work);
+ int voltage, i, ret;
+
+ dev_dbg(bq->dev, "Start to request input voltage increasing\n");
+
+ /* Enable current pulse voltage control protocol */
+ ret = bq25890_field_write(bq, F_PUMPX_EN, 1);
+ if (ret < 0)
+ goto error_print;
+
+ for (i = 0; i < PUMP_EXPRESS_MAX_TRIES; i++) {
+ voltage = bq25890_get_vbus_voltage(bq);
+ if (voltage < 0)
+ goto error_print;
+ dev_dbg(bq->dev, "input voltage = %d uV\n", voltage);
+
+ if ((voltage + PUMP_EXPRESS_VBUS_MARGIN_uV) >
+ bq->pump_express_vbus_max)
+ break;
+
+ ret = bq25890_field_write(bq, F_PUMPX_UP, 1);
+ if (ret < 0)
+ goto error_print;
+
+ /* Note a single PUMPX up pulse-sequence takes 2.1s */
+ ret = regmap_field_read_poll_timeout(bq->rmap_fields[F_PUMPX_UP],
+ ret, !ret, 100000, 3000000);
+ if (ret < 0)
+ goto error_print;
+
+ /* Make sure ADC has sampled Vbus before checking again */
+ msleep(1000);
+ }
+
+ bq25890_field_write(bq, F_PUMPX_EN, 0);
+
+ dev_info(bq->dev, "Hi-voltage charging requested, input voltage is %d mV\n",
+ voltage);
+
+ return;
+error_print:
+ dev_err(bq->dev, "Failed to request hi-voltage charging\n");
+}
+
static void bq25890_usb_work(struct work_struct *data)
{
int ret;
@@ -1068,6 +1139,10 @@ static int bq25890_fw_probe(struct bq25890_device *bq)
int ret;
struct bq25890_init_data *init = &bq->init_data;
+ /* Optional, left at 0 if property is not present */
+ device_property_read_u32(bq->dev, "linux,pump-express-vbus-max",
+ &bq->pump_express_vbus_max);
+
bq->skip_reset = device_property_read_bool(bq->dev, "linux,skip-reset");
bq->read_back_init_data = device_property_read_bool(bq->dev,
"linux,read-back-settings");
@@ -1100,6 +1175,7 @@ static int bq25890_probe(struct i2c_client *client,
bq->dev = dev;
mutex_init(&bq->lock);
+ INIT_DELAYED_WORK(&bq->pump_express_work, bq25890_pump_express_work);
bq->rmap = devm_regmap_init_i2c(client, &bq25890_regmap_config);
if (IS_ERR(bq->rmap))
--
2.33.1
