Thanks again for your time. My response inline.
On 02-Nov-18 11:57 PM, Andy Shevchenko wrote:
On Fri, Nov 2, 2018 at 12:29 PM Rajneesh Bhardwaj
<rajneesh.bhardwaj@xxxxxxxxxxxxxxx> wrote:
This adds support to show the Latency Tolerance Reporting for the IPs on
the PCH as reported by the PMC. The format shown here is raw LTR data
payload that can further be decoded as per the PCI specification.
This also fixes some minor alignment issues in the header file by
removing spaces and converting to tabs at some places.
Thanks for the update, my comments below.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@xxxxxxxxxxxxxxx>
[andy: fixed output to avoid LTR duplication and put space after colon]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
You incorporated changes I proposed — good!
But please, don't do my job with signing stuff, etc. Just mention what
you did in the changelog.
Okay. I downloaded the patch applied on review-andy branch and worked
on it. Those two lines came along with the downloaded patch but i
understood your concern now.
+static const struct pmc_bit_map spt_ltr_show_map[] = {
+ {"SOUTHPORT_A", SPT_PMC_LTR_SPA},
+ {"SOUTHPORT_B", SPT_PMC_LTR_SPB},
+ {"SATA", SPT_PMC_LTR_SATA},
+ {"GIGABIT_ETHERNET", SPT_PMC_LTR_GBE},
+ {"XHCI", SPT_PMC_LTR_XHCI},
+ /* IP 5 is reserved */
Since we dropped explicit numbering, this line and similar sounds redundant.
Fine.
+ {"ME", SPT_PMC_LTR_ME},
+ /* EVA is Enterprise Value Add, doesn't really exist on PCH */
+ {"EVA", SPT_PMC_LTR_EVA},
+ {"SOUTHPORT_C", SPT_PMC_LTR_SPC},
+ {"HD_AUDIO", SPT_PMC_LTR_AZ},
+ /* IP 10 is reserved */
+ {"LPSS", SPT_PMC_LTR_LPSS},
+ {"SOUTHPORT_D", SPT_PMC_LTR_SPD},
+ {"SOUTHPORT_E", SPT_PMC_LTR_SPE},
+ {"CAMERA", SPT_PMC_LTR_CAM},
+ {"ESPI", SPT_PMC_LTR_ESPI},
+ {"SCC", SPT_PMC_LTR_SCC},
+ {"ISH", SPT_PMC_LTR_ISH},
+ /* Below two cannot be used for LTR_IGNORE */
+ {"CURRENT_PLATFORM", SPT_PMC_LTR_CUR_PLT},
+ {"AGGREGATED_SYSTEM", SPT_PMC_LTR_CUR_ASLT},
+ {}
+};
/* Cannonlake Power Management Controller register offsets */
-#define CNP_PMC_SLP_S0_RES_COUNTER_OFFSET 0x193C
-#define CNP_PMC_LTR_IGNORE_OFFSET 0x1B0C
-#define CNP_PMC_PM_CFG_OFFSET 0x1818
+#define CNP_PMC_SLP_S0_RES_COUNTER_OFFSET 0x193C
+#define CNP_PMC_LTR_IGNORE_OFFSET 0x1B0C
+#define CNP_PMC_PM_CFG_OFFSET 0x1818
#define CNP_PMC_SLPS0_DBG_OFFSET 0x10B4
Can we preserve ordering?
Doesn't harm, will reorder based on offsets increasing order.
/* Cannonlake: PGD PFET Enable Ack Status Register(s) start */
-#define CNP_PMC_HOST_PPFEAR0A 0x1D90
+#define CNP_PMC_HOST_PPFEAR0A 0x1D90
What's wrong with this line? Why is it changed?
This and below are edited to convert spaces to tabs. This is captured in
commit message too.
-#define CNP_PMC_MMIO_REG_LEN 0x2000
-#define CNP_PPFEAR_NUM_ENTRIES 8
-#define CNP_PMC_READ_DISABLE_BIT 22
+#define CNP_PMC_MMIO_REG_LEN 0x2000
+#define CNP_PPFEAR_NUM_ENTRIES 8
+#define CNP_PMC_READ_DISABLE_BIT 22
What happened to these lines?
same as above.
#define CNP_PMC_LATCH_SLPS0_EVENTS BIT(31)
Perhaps
+ blank line
here
This is from a previous commit but i think its better to move it up the
block and insert one blank line after. If we insert one blank line after
its current position, it looks odd and cuts the logical block unnecessarily.
+#define CNP_PMC_LTR_CUR_PLT 0x1B50
+#define CNP_PMC_LTR_CUR_ASLT 0x1B54
+#define CNP_PMC_LTR_SPA 0x1B60
+#define CNP_PMC_LTR_SPB 0x1B64
+#define CNP_PMC_LTR_SATA 0x1B68
+#define CNP_PMC_LTR_GBE 0x1B6C
+#define CNP_PMC_LTR_XHCI 0x1B70
+#define CNP_PMC_LTR_ME 0x1B78
+#define CNP_PMC_LTR_EVA 0x1B7C
+#define CNP_PMC_LTR_SPC 0x1B80
+#define CNP_PMC_LTR_AZ 0x1B84
+#define CNP_PMC_LTR_LPSS 0x1B8C
+#define CNP_PMC_LTR_CAM 0x1B90
+#define CNP_PMC_LTR_SPD 0x1B94
+#define CNP_PMC_LTR_SPE 0x1B98
+#define CNP_PMC_LTR_ESPI 0x1B9C
+#define CNP_PMC_LTR_SCC 0x1BA0
+#define CNP_PMC_LTR_ISH 0x1BA4
+#define CNP_PMC_LTR_CNV 0x1BF0
+#define CNP_PMC_LTR_EMMC 0x1BF4
+#define CNP_PMC_LTR_UFSX2 0x1BF8
