Add documentation for mlxreg-io platform driver sysfs interfaces to allow user space access for system resets control, reset causes monitoring, programmable devices version reading and device selection control. Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx> --- v4: Comments pointed out by Greg: Add Documentation/ABI/ entries for the new sysfs files. v4-v5: Comments pointed out by Darren: - Rename cause to reset. - Extend explanation in doc file. Changes added by Vadim: - Add two new attributes. - Re-arrange in alphabetic order after changes. - Change date from May to June. --- Documentation/ABI/stable/sysfs-driver-mlxreg-io | 77 +++++++++++++++++++++++++ 1 file changed, 77 insertions(+) create mode 100644 Documentation/ABI/stable/sysfs-driver-mlxreg-io diff --git a/Documentation/ABI/stable/sysfs-driver-mlxreg-io b/Documentation/ABI/stable/sysfs-driver-mlxreg-io new file mode 100644 index 0000000..7913a95 --- /dev/null +++ b/Documentation/ABI/stable/sysfs-driver-mlxreg-io @@ -0,0 +1,77 @@ +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ + asic_health + +Date: June 2018 +KernelVersion: 4.18 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file shows ASIC health status. The possible values are: + 0 - health failed, 2 - health OK, 3 - ASIC in booting state. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ + cpld1_version + cpld2_version + +Date: June 2018 +KernelVersion: 4.18 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show with which CPLD versions have been burned + on carrier and switch boards. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/select_iio +Date: June 2018 +KernelVersion: 4.18 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file allows iio devices selection. + + Attribute select_iio can be written with 0 or with 1. It + selects which one of iio devices can be accessed. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu1_on + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu2_on + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_cycle + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_down +Date: June 2018 +KernelVersion: 4.18 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files allow asserting system power cycling, switching + power supply units on and off and system's main power domain + shutdown. + Expected behavior: + When pwr_cycle is written 1: auxiliary power domain will go + down and after short period (about 1 second) up. + When psu1_on or psu2_on is written 1, related unit will be + disconnected from the power source, when written 0 - connected. + If both are written 1 - power supplies main power domain will + go down. + When pwr_down is written 1, system's main power domain will go + down. + + The files are write only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ + reset_aux_pwr_or_ref + reset_asic_thermal + reset_hotswap_or_wd + reset_fw_reset + reset_long_pb + reset_main_pwr_fail + reset_short_pb + reset_sw_reset +Date: June 2018 +KernelVersion: 4.18 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show the system reset cause, as following: power + auxiliary outage or power refresh, ASIC thermal shutdown, + hotswap or watchdog, firmware reset, long press power button, + short press power button, software reset. Value 1 in file means + this is reset cause, 0 - otherwise. Only one of the above + causes could be 1 at the same time, representing only last + reset cause. + + The files are read only. -- 2.1.4
