From: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
Enable system support for the Mellanox Technologies hotplug platform
driver, which provides support for the next Mellanox basic systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100" and also various number of derivative
systems from the above basic types.
This driver handles hot-plug events for the power suppliers, power
cables and fans for the above systems.
The Kconfig currently controlling compilation of this code is:
driver/platform/x86:config MLX_CPLD_PLATFORM
tristate "Mellanox platform hotplug driver support"
Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
---
MAINTAINERS | 7 +
drivers/platform/x86/Kconfig | 10 +
drivers/platform/x86/Makefile | 1 +
drivers/platform/x86/mlxcpld-hotplug.c | 543 ++++++++++++++++++++++++++
include/linux/platform_data/mlxcpld-hotplug.h | 90 +++++
5 files changed, 651 insertions(+)
create mode 100644 drivers/platform/x86/mlxcpld-hotplug.c
create mode 100644 include/linux/platform_data/mlxcpld-hotplug.h
diff --git a/MAINTAINERS b/MAINTAINERS
index a306795..cbfe2a8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7649,6 +7649,13 @@ W: http://www.mellanox.com
Q: http://patchwork.ozlabs.org/project/netdev/list/
F: drivers/net/ethernet/mellanox/mlxsw/
+MELLANOX MLX CPLD HOTPLUG DRIVER
+M: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
+L: platform-driver-x86@xxxxxxxxxxxxxxx
+S: Supported
+F: drivers/platform/x86/mlxcpld-hotplug.c
+F: include/linux/platform_data/mlxcpld-hotplug.h
+
SOFT-ROCE DRIVER (rxe)
M: Moni Shoua <monis@xxxxxxxxxxxx>
L: linux-rdma@xxxxxxxxxxxxxxx
diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 81b8dcc..e9be541 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -1026,4 +1026,14 @@ config INTEL_TELEMETRY
used to get various SoC events and parameters
directly via debugfs files. Various tools may use
this interface for SoC state monitoring.
+
+config MLX_CPLD_PLATFORM
+ tristate "Mellanox platform hotplug driver support"
+ default n
+ depends on MLX_PLATFORM
+ select I2C
+ ---help---
+ This driver handles hot-plug events for the power suppliers, power
+ cables and fans on the wide range Mellanox IB and Ethernet systems.
+
endif # X86_PLATFORM_DEVICES
diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
index 2efa86d..1f06b63 100644
--- a/drivers/platform/x86/Makefile
+++ b/drivers/platform/x86/Makefile
@@ -71,3 +71,4 @@ obj-$(CONFIG_INTEL_TELEMETRY) += intel_telemetry_core.o \
intel_telemetry_pltdrv.o \
intel_telemetry_debugfs.o
obj-$(CONFIG_INTEL_PMC_CORE) += intel_pmc_core.o
+obj-$(CONFIG_MLX_CPLD_PLATFORM) += mlxcpld-hotplug.o
diff --git a/drivers/platform/x86/mlxcpld-hotplug.c b/drivers/platform/x86/mlxcpld-hotplug.c
new file mode 100644
index 0000000..d53d845
--- /dev/null
+++ b/drivers/platform/x86/mlxcpld-hotplug.c
@@ -0,0 +1,543 @@
+/*
+ * drivers/platform/x86/mlxcpld-hotplug.c
+ * Copyright (c) 2016 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2016 Vadim Pasternak <vadimp@xxxxxxxxxxxx>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the names of the copyright holders nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_data/mlxcpld-hotplug.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/wait.h>
+#include <linux/workqueue.h>
+
+/* Offset of event and mask registers from status register */
+#define MLXCPLD_HOTPLUG_EVENT_OFF 1
+#define MLXCPLD_HOTPLUG_MASK_OFF 2
+#define MLXCPLD_HOTPLUG_AGGR_MASK_OFF 1
+
+#define MLXCPLD_HOTPLUG_ATTRS_NUM 8
+
+enum mlxcpld_hotplug_attr_type {
+ MLXCPLD_HOTPLUG_ATTR_TYPE_PSU,
+ MLXCPLD_HOTPLUG_ATTR_TYPE_PWR,
+ MLXCPLD_HOTPLUG_ATTR_TYPE_FAN,
+};
+
+/* mlxcpld_hotplug_priv_data - platform private data:
+ * @irq - platform interrupt number;
+ * @pdev - platform device;
+ * @plat - platform data;
+ * @hwmon - hwmon device;
+ * @mlxcpld_hotplug_attr - sysfs attributes array;
+ * @mlxcpld_hotplug_dev_attr - sysfs sensor device attribute array;
+ * @group - sysfs attribute group;
+ * @groups - list of sysfs attribute group for hwmon registration;
+ * @dwork - delayed work template;
+ * @lock - spin lock;
+ * @aggr_cache - last value of aggregation register status;
+ * @psu_cache - last value of PSU register status;
+ * @pwr_cache - last value of power register status;
+ * @fan_cache - last value of FAN register status;
+ */
+struct mlxcpld_hotplug_priv_data {
+ int irq;
+ struct platform_device *pdev;
+ struct mlxcpld_hotplug_platform_data *plat;
+ struct device *hwmon;
+ struct attribute *mlxcpld_hotplug_attr[MLXCPLD_HOTPLUG_ATTRS_NUM + 1];
+ struct sensor_device_attribute_2
+ mlxcpld_hotplug_dev_attr[MLXCPLD_HOTPLUG_ATTRS_NUM];
+ struct attribute_group group;
+ const struct attribute_group *groups[2];
+ struct delayed_work dwork;
+ spinlock_t lock;
+ u8 aggr_cache;
+ u8 psu_cache;
+ u8 pwr_cache;
+ u8 fan_cache;
+};
+
+static ssize_t mlxcpld_hotplug_attr_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mlxcpld_hotplug_priv_data *priv = platform_get_drvdata(pdev);
+ int index = to_sensor_dev_attr_2(attr)->index;
+ int nr = to_sensor_dev_attr_2(attr)->nr;
+ u8 reg_val = 0;
+
+ switch (nr) {
+ case MLXCPLD_HOTPLUG_ATTR_TYPE_PSU:
+ reg_val = inb(priv->plat->psu_reg_offset);
+ reg_val &= BIT_MASK(index);
+ reg_val = !!!reg_val; /* Bit = 0 : PSU is present. */
+ break;
+
+ case MLXCPLD_HOTPLUG_ATTR_TYPE_PWR:
+ reg_val = inb(priv->plat->pwr_reg_offset);
+ reg_val &= BIT_MASK(index % priv->plat->pwr_count);
+ reg_val = !!reg_val; /* Bit = 1 : power cable is attached. */
+ break;
+
+ case MLXCPLD_HOTPLUG_ATTR_TYPE_FAN:
+ reg_val = inb(priv->plat->fan_reg_offset);
+ reg_val &= BIT_MASK(index % priv->plat->fan_count);
+ reg_val = !!!reg_val; /* Bit = 0 : FAN is present. */
+ break;
+ }
+
+ return sprintf(buf, "%u\n", reg_val);
+}
+
+static int mlxcpld_hotplug_attr_init(struct mlxcpld_hotplug_priv_data *priv)
+{
+ int num_attrs = priv->plat->psu_count + priv->plat->pwr_count +
+ priv->plat->fan_count;
+ int i;
+
+ priv->group.attrs = devm_kzalloc(&priv->pdev->dev, num_attrs *
+ sizeof(struct attribute *),
+ GFP_KERNEL);
+ if (!priv->group.attrs)
+ return -ENOMEM;
+
+ for (i = 0; i < num_attrs; i++) {
+ priv->mlxcpld_hotplug_attr[i] =
+ &priv->mlxcpld_hotplug_dev_attr[i].dev_attr.attr;
+
+ if (i < priv->plat->psu_count) {
+ priv->mlxcpld_hotplug_attr[i]->name =
+ devm_kasprintf(&priv->pdev->dev, GFP_KERNEL,
+ "psu%u", i + 1);
+ priv->mlxcpld_hotplug_dev_attr[i].nr =
+ MLXCPLD_HOTPLUG_ATTR_TYPE_PSU;
+ } else if (i < priv->plat->psu_count + priv->plat->pwr_count) {
+ priv->mlxcpld_hotplug_attr[i]->name =
+ devm_kasprintf(&priv->pdev->dev, GFP_KERNEL,
+ "pwr%u", i %
+ priv->plat->pwr_count + 1);
+ priv->mlxcpld_hotplug_dev_attr[i].nr =
+ MLXCPLD_HOTPLUG_ATTR_TYPE_PWR;
+ } else {
+ priv->mlxcpld_hotplug_attr[i]->name =
+ devm_kasprintf(&priv->pdev->dev, GFP_KERNEL,
+ "fan%u", i %
+ priv->plat->fan_count + 1);
+ priv->mlxcpld_hotplug_dev_attr[i].nr =
+ MLXCPLD_HOTPLUG_ATTR_TYPE_FAN;
+ }
+
+ if (!priv->mlxcpld_hotplug_attr[i]->name) {
+ dev_err(&priv->pdev->dev, "Memory allocation failed for sysfs attribute %d.\n",
+ i + 1);
+ return -ENOMEM;
+ }
+
+ priv->mlxcpld_hotplug_dev_attr[i].dev_attr.attr.name =
+ priv->mlxcpld_hotplug_attr[i]->name;
+ priv->mlxcpld_hotplug_dev_attr[i].dev_attr.attr.mode =
+ S_IRUGO;
+ priv->mlxcpld_hotplug_dev_attr[i].dev_attr.show =
+ mlxcpld_hotplug_attr_show;
+ priv->mlxcpld_hotplug_dev_attr[i].index = i;
+ sysfs_attr_init(
+ &priv->mlxcpld_hotplug_dev_attr[i].dev_attr.attr);
+ }
+
+ priv->group.attrs = priv->mlxcpld_hotplug_attr;
+ priv->groups[0] = &priv->group;
+ priv->groups[1] = NULL;
+
+ return 0;
+}
+
+static int mlxcpld_hotplug_device_create(struct device *dev,
+ struct mlxcpld_hotplug_device *item)
+{
+ item->adapter = i2c_get_adapter(item->bus);
+ if (!item->adapter) {
+ dev_err(dev, "Failed to get adapter for bus %d\n",
+ item->bus);
+ return -EFAULT;
+ }
+
+ item->client = i2c_new_device(item->adapter, &item->brdinfo);
+ if (!item->client) {
+ dev_err(dev, "Failed to create client %s at bus %d at addr 0x%02x\n",
+ item->brdinfo.type, item->bus, item->brdinfo.addr);
+ i2c_put_adapter(item->adapter);
+ item->adapter = NULL;
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+static void mlxcpld_hotplug_device_destroy(struct mlxcpld_hotplug_device *item)
+{
+ if (item->client) {
+ i2c_unregister_device(item->client);
+ item->client = NULL;
+ }
+
+ if (item->adapter) {
+ i2c_put_adapter(item->adapter);
+ item->adapter = NULL;
+ }
+}
+
+/* mlxcpld_hotplug_work_handler - performs traversing of CPLD interrupt
+ * registers according to the below hierarchy schema:
+ *
+ * Aggregation registers (status/mask)
+ * PSU registers: *---*
+ * *-----------------* | |
+ * |status/event/mask|----->| * |
+ * *-----------------* | |
+ * Power registers: | |
+ * *-----------------* | |
+ * |status/event/mask|----->| * |---> CPU
+ * *-----------------* | |
+ * FAN registers:
+ * *-----------------* | |
+ * |status/event/mask|----->| * |
+ * *-----------------* | |
+ * *---*
+ * In case some system changed are detected: FAN in/out, PSU in/out, power
+ * cable attached/detached, relevant device is created or destroyed.
+ */
+static void mlxcpld_hotplug_work_handler(struct work_struct *work)
+{
+ struct mlxcpld_hotplug_priv_data *priv = container_of(work,
+ struct mlxcpld_hotplug_priv_data, dwork.work);
+ u8 val, aggr_asserted, asserted;
+ unsigned long flags;
+ int bit;
+
+ /* Mask aggregation event. */
+ outb(0, priv->plat->top_aggr_offset + MLXCPLD_HOTPLUG_AGGR_MASK_OFF);
+ /* Read aggregation status. */
+ val = inb(priv->plat->top_aggr_offset);
+ val &= priv->plat->top_aggr_mask;
+ aggr_asserted = priv->aggr_cache ^ val;
+ priv->aggr_cache = val;
+
+ if (aggr_asserted & priv->plat->top_aggr_psu_mask) {
+ /* Mask psu presense event. */
+ outb(0, priv->plat->psu_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Read psu presense status. */
+ val = inb(priv->plat->psu_reg_offset);
+ val &= priv->plat->psu_mask;
+ asserted = priv->psu_cache ^ val;
+ priv->psu_cache = val;
+
+ if (priv->plat->psu) {
+ for_each_set_bit(bit, (unsigned long *)&asserted, 8) {
+ if (val & BIT(bit))
+ mlxcpld_hotplug_device_destroy(
+ priv->plat->psu + bit);
+ else
+ mlxcpld_hotplug_device_create(
+ &priv->pdev->dev,
+ priv->plat->psu + bit);
+ }
+ }
+
+ /* Acknowledge psu presense event. */
+ outb(0, priv->plat->psu_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Unmask psu presense event. */
+ outb(priv->plat->psu_mask, priv->plat->psu_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ }
+
+ if (aggr_asserted & priv->plat->top_aggr_pwr_mask) {
+ /* Mask power cable event. */
+ outb(0, priv->plat->pwr_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Read power cable status. */
+ val = inb(priv->plat->pwr_reg_offset);
+ val &= priv->plat->pwr_mask;
+ asserted = priv->pwr_cache ^ val;
+ priv->pwr_cache = val;
+
+ if (priv->plat->pwr) {
+ for_each_set_bit(bit, (unsigned long *)&asserted, 8) {
+ if (val & BIT(bit))
+ mlxcpld_hotplug_device_create(
+ &priv->pdev->dev,
+ priv->plat->pwr + bit);
+ else
+ mlxcpld_hotplug_device_destroy(
+ priv->plat->pwr + bit);
+ }
+ }
+
+ /* Acknowledge power cable event. */
+ outb(0, priv->plat->pwr_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Unmask power cable event */
+ outb(priv->plat->pwr_mask, priv->plat->pwr_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ }
+
+ if (aggr_asserted & priv->plat->top_aggr_fan_mask) {
+ /* Mask fan presense event. */
+ outb(0, priv->plat->fan_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Read fan presense status. */
+ val = inb(priv->plat->fan_reg_offset);
+ val &= priv->plat->fan_mask;
+ asserted = priv->fan_cache ^ val;
+ priv->fan_cache = val;
+
+ if (priv->plat->fan) {
+ for_each_set_bit(bit, (unsigned long *)&asserted, 8) {
+ if (val & BIT(bit))
+ mlxcpld_hotplug_device_destroy(
+ priv->plat->fan + bit);
+ else
+ mlxcpld_hotplug_device_create(
+ &priv->pdev->dev,
+ priv->plat->fan + bit);
+ }
+ }
+
+ /* Acknowledge fan presense event. */
+ outb(0, priv->plat->fan_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Unmask fan presense event. */
+ outb(priv->plat->fan_mask, priv->plat->fan_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ /* Unmask aggregation event (no need acknowledge). */
+ outb(priv->plat->top_aggr_mask, priv->plat->top_aggr_offset +
+ MLXCPLD_HOTPLUG_AGGR_MASK_OFF);
+
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ /*
+ * It is possible, that some signals have been inserted, while
+ * interrupt has been masked by mlxcpld_hotplug_work_handler.
+ * In this case such signals will be missed. In order to handle
+ * these signals delayed work is canceled and work task
+ * re-scheduled for immediate execution. It allows to handle
+ * missed signals, if any. In other case work handler just
+ * validates that no new signals have been received during
+ * masking.
+ */
+ cancel_delayed_work(&priv->dwork);
+ schedule_delayed_work(&priv->dwork, 0);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return;
+ }
+
+ /* Unmask aggregation event (no need acknowledge). */
+ outb(priv->plat->top_aggr_mask, priv->plat->top_aggr_offset +
+ MLXCPLD_HOTPLUG_AGGR_MASK_OFF);
+}
+
+static void mlxcpld_hotplug_set_irq(struct mlxcpld_hotplug_priv_data *priv)
+{
+ /* Clear psu presense event. */
+ outb(0, priv->plat->psu_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Set psu initial status as mask and unmask psu event. */
+ priv->psu_cache = priv->plat->psu_mask;
+ outb(priv->plat->psu_mask, priv->plat->psu_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ /* Clear power cable event. */
+ outb(0, priv->plat->pwr_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Keep power initial status as zero and unmask power event. */
+ outb(priv->plat->pwr_mask, priv->plat->pwr_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ /* Clear fan presense event. */
+ outb(0, priv->plat->fan_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+ /* Set fan initial status as mask and unmask fan event. */
+ priv->fan_cache = priv->plat->fan_mask;
+ outb(priv->plat->fan_mask, priv->plat->fan_reg_offset +
+ MLXCPLD_HOTPLUG_MASK_OFF);
+
+ /* Keep aggregation initial status as zero and unmask events. */
+ outb(priv->plat->top_aggr_mask, priv->plat->top_aggr_offset +
+ MLXCPLD_HOTPLUG_AGGR_MASK_OFF);
+
+ /* Invoke work handler for initializing hot plug devices setting. */
+ mlxcpld_hotplug_work_handler(&priv->dwork.work);
+
+ enable_irq(priv->irq);
+}
+
+static void mlxcpld_hotplug_unset_irq(struct mlxcpld_hotplug_priv_data *priv)
+{
+ int i;
+
+ disable_irq(priv->irq);
+ cancel_delayed_work_sync(&priv->dwork);
+
+ /* Mask aggregation event. */
+ outb(0, priv->plat->top_aggr_offset + MLXCPLD_HOTPLUG_AGGR_MASK_OFF);
+
+ /* Mask psu presense event. */
+ outb(0, priv->plat->psu_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Clear psu presense event. */
+ outb(0, priv->plat->psu_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+
+ /* Mask power cable event. */
+ outb(0, priv->plat->pwr_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Clear power cable event. */
+ outb(0, priv->plat->pwr_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+
+ /* Mask fan presense event. */
+ outb(0, priv->plat->fan_reg_offset + MLXCPLD_HOTPLUG_MASK_OFF);
+ /* Clear fan presense event. */
+ outb(0, priv->plat->fan_reg_offset + MLXCPLD_HOTPLUG_EVENT_OFF);
+
+ /* Remove all the attached devices. */
+ for (i = 0; i < priv->plat->psu_count; i++)
+ mlxcpld_hotplug_device_destroy(priv->plat->psu + i);
+
+ for (i = 0; i < priv->plat->pwr_count; i++)
+ mlxcpld_hotplug_device_destroy(priv->plat->pwr + i);
+
+ for (i = 0; i < priv->plat->fan_count; i++)
+ mlxcpld_hotplug_device_destroy(priv->plat->fan + i);
+}
+
+static irqreturn_t mlxcpld_hotplug_irq_handler(int irq, void *dev)
+{
+ struct mlxcpld_hotplug_priv_data *priv =
+ (struct mlxcpld_hotplug_priv_data *)dev;
+
+ /* Schedule work task for immediate execution.*/
+ schedule_delayed_work(&priv->dwork, 0);
+
+ return IRQ_HANDLED;
+}
+
+static int mlxcpld_hotplug_probe(struct platform_device *pdev)
+{
+ struct mlxcpld_hotplug_platform_data *pdata;
+ struct mlxcpld_hotplug_priv_data *priv;
+ int err;
+
+ pdata = dev_get_platdata(&pdev->dev);
+ if (!pdata) {
+ dev_err(&pdev->dev, "Failed to get platform data.\n");
+ return -EINVAL;
+ }
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->pdev = pdev;
+ priv->plat = pdata;
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq < 0) {
+ dev_err(&pdev->dev, "Failed to get platform irq: %d\n",
+ priv->irq);
+ return priv->irq;
+ }
+
+ err = devm_request_irq(&pdev->dev, priv->irq,
+ mlxcpld_hotplug_irq_handler, 0, pdev->name,
+ priv);
+ if (err) {
+ dev_err(&pdev->dev, "Failed to request irq: %d\n", err);
+ return err;
+ }
+ disable_irq(priv->irq);
+
+ INIT_DELAYED_WORK(&priv->dwork, mlxcpld_hotplug_work_handler);
+ spin_lock_init(&priv->lock);
+
+ err = mlxcpld_hotplug_attr_init(priv);
+ if (err) {
+ dev_err(&pdev->dev, "Failed to allocate attributes: %d\n", err);
+ return err;
+ }
+
+ priv->hwmon = devm_hwmon_device_register_with_groups(&pdev->dev,
+ "mlxcpld_hotplug", priv, priv->groups);
+ if (IS_ERR(priv->hwmon)) {
+ dev_err(&pdev->dev, "Failed to register hwmon device %ld\n",
+ PTR_ERR(priv->hwmon));
+ return PTR_ERR(priv->hwmon);
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ /* Perform initial interrupts setup. */
+ mlxcpld_hotplug_set_irq(priv);
+
+ return 0;
+}
+
+static int mlxcpld_hotplug_remove(struct platform_device *pdev)
+{
+ struct mlxcpld_hotplug_priv_data *priv = platform_get_drvdata(pdev);
+
+ /* Clean interrupts setup. */
+ mlxcpld_hotplug_unset_irq(priv);
+
+ return 0;
+}
+
+static struct platform_driver mlxcpld_hotplug_driver = {
+ .driver = {
+ .name = "mlxcpld-hotplug",
+ },
+ .probe = mlxcpld_hotplug_probe,
+ .remove = mlxcpld_hotplug_remove,
+};
+
+module_platform_driver(mlxcpld_hotplug_driver);
+
+MODULE_AUTHOR("Vadim Pasternak <vadimp@xxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Mellanox CPLD hotplug platform driver");
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_ALIAS("platform:mlxcpld-hotplug");
diff --git a/include/linux/platform_data/mlxcpld-hotplug.h b/include/linux/platform_data/mlxcpld-hotplug.h
new file mode 100644
index 0000000..ebb942c
--- /dev/null
+++ b/include/linux/platform_data/mlxcpld-hotplug.h
@@ -0,0 +1,90 @@
+/*
+ * include/linux/platform_data/mlxcpld-hotplug.h
+ * Copyright (c) 2016 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2016 Vadim Pasternak <vadimp@xxxxxxxxxxxx>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the names of the copyright holders nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H
+#define __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H
+
+/* mlxcpld_hotplug_device - I2C device data:
+ * @adapter - ;
+ * @client - ;
+ * @brdinfo - ;
+ * @bus - ;
+ */
+struct mlxcpld_hotplug_device {
+ struct i2c_adapter *adapter;
+ struct i2c_client *client;
+ struct i2c_board_info brdinfo;
+ u16 bus;
+};
+
+/* mlxcpld_hotplug_platform_data - device platform data:
+ * @top_aggr_offset - offset of top aggregation interrupt register;
+ * @top_aggr_mask - top aggregation interrupt common mask;
+ * @top_aggr_psu_mask - top aggregation interrupt PSU mask;
+ * @psu_reg_offset - offset of PSU interrupt register;
+ * @psu_mask - PSU interrupt mask;
+ * @psu_count - number of equipped replaceable PSUs;
+ * @psu - pointer to PSU devices data array;
+ * @top_aggr_pwr_mask - top aggregation interrupt power mask;
+ * @pwr_reg_offset - offset of power interrupt register
+ * @pwr_mask - power interrupt mask;
+ * @pwr_count - number of power sources;
+ * @pwr - pointer to power devices data array;
+ * @top_aggr_fan_mask - top aggregation interrupt FAN mask;
+ * @fan_reg_offset - offset of FAN interrupt register;
+ * @fan_mask - FAN interrupt mask;
+ * @fan_count - number of equipped replaceable FANs;
+ * @fan - pointer to FAN devices data array;
+ */
+struct mlxcpld_hotplug_platform_data {
+ u16 top_aggr_offset;
+ u8 top_aggr_mask;
+ u8 top_aggr_psu_mask;
+ u16 psu_reg_offset;
+ u8 psu_mask;
+ u8 psu_count;
+ struct mlxcpld_hotplug_device *psu;
+ u8 top_aggr_pwr_mask;
+ u16 pwr_reg_offset;
+ u8 pwr_mask;
+ u8 pwr_count;
+ struct mlxcpld_hotplug_device *pwr;
+ u8 top_aggr_fan_mask;
+ u16 fan_reg_offset;
+ u8 fan_mask;
+ u8 fan_count;
+ struct mlxcpld_hotplug_device *fan;
+};
+
+#endif /* __LINUX_PLATFORM_DATA_MLXCPLD_HOTPLUG_H */
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe platform-driver-x86" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
