Hi, Mika, I've been reading the thread about pinctrl-cherryview interrupts, but I have some basic questions in understanding the hardware and the relationship between ACPI and Linux drivers, so I decided to start a new thread. https://lkml.kernel.org/g/20160909085832.GK15313@xxxxxxxxxxxxxxxxxx I have one Asus E200HA (Atom x5-Z8300) where the power button doesn't generate any ACPI events (no SCI), instead it causes a Thermal Event irq: TRM: 3 3 3 4 Thermal event interrupts [ 51.825488] CPU0: Core temperature above threshold, cpu clock throttled (total events = 1) [ 51.826933] CPU1: Core temperature above threshold, cpu clock throttled (total events = 1) [ 51.826965] mce: [Hardware Error]: Machine check events logged [ 51.841180] mce: [Hardware Error]: Machine check events logged (These events are logged only sometimes, usually a power button press only increments the TRM count.) I would like to understand how this is possible, when I boot with apic=debug I can't see anything claiming vector 0xfa. The LID causes a gpio irq: 158: 2 0 0 0 chv-gpio 43 ACPI:Event However, neither LID nor power button can wake up the device from "echo freeze >/sys/power/state". :-( "grep . /sys/firmware/acpi/interrupts/*" shows only zeros. I put the DSDT and some other tables at: https://linuxtv.org/~js/e200ha/ During the last weeks I read what I could about the hardware and ACPI, and poked at it with acpidbg, devmem, ioport and in kernel source, but to no avail. On Thu, Sep 15, 2016 at 06:52:10PM +0300, Mika Westerberg wrote: > It turns out that for north and southwest communities, they can only > generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper > part (8-15) can only generate GPEs (General Purpose Events). I got the Atom Z8000 series datasheet from http://www.intel.com/content/www/us/en/processors/atom/atom-technical-resources.html and tried to find the source for this. The closest I could find is the GPIO_ROUT PMC register? However, the datasheet doesn't tell about the other interrupts not covered by GPIO_ROUT, if they are fixed IRQ or SCI or "no effect". I also don't get the mapping from intsel irq to IO-APIC pin number. And also not the mapping between the pin numbers used on DSDT GpioInt to the pin numbers in pinctrl-cherryview.c. Could you shed a light on this? Or point out where I can find information? It seems to imply BIOS sets up IntSel. I'm generally confused about the responsibility of BIOS vs. drivers making use of the information from DSDT, e.g. Device (GPO1) has a list of GpioIo Connections, other devices like PMI2 use GpioInt from GPO1. My E200HA has the INT33F5 TI PMIC Controller, which according to Windows driver strings seems to be the SND9039. Does it mean I need a PMIC driver that reads the _CRS and configures the GPIO? BTW, the datasheet talks about 4 seconds for power button override, but it takes 10 seconds. Maybe it means the power button is connected to the TI PMIC, not to the Cherryview SoC? Another question is about the virtual GPIO device that exists in hardware and is used by DSDT. How does that work and why does pinctrl-cherryview.c exclude it? Sorry for so many questions, any info is appreciated, and any suggestion what to try to get the thing to wake up from freeze. I was totally unfamiliar with ACPI until now, but I think the DSDT has some nasty surprise in several _REG methods that use OEM defined OperatingRegionIds to set some availabilty flags that are tested in other methods. So it means if the Windows drivers aren't loaded, those methods won't do anything, right? Does anyone have suggestions or even examples how to deal with this? Thanks, Johannes -- To unsubscribe from this list: send the line "unsubscribe platform-driver-x86" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
