Hi Joey Lee, On Thursday 10 March 2011 23:02:27 Joey Lee wrote: > æ åï2011-03-10 æ 19:37 +0100ïOldÅich JedliÄka æåï > > > Hi all, > > > > This is about Acer WMI driver and bluetooth support. I hope I'm at the > > right place with my question :-) > > > > I tried to use bluetooth again on my Acer TravelMate 5730G and discovered > > a usability problem. I've checked 2.6.38-rc7: > > > > 0. On startup, the bluetooth LED is off, acer-bluetooth SW rfkill is > > blocked. > > Yes, this is right behavior. > > Because have a acer-wmi patch in 2.6.38 to sync the connection devices > (wlan, bluetooth, 3G) status with BIOS. > Acer BIOS fills-in the device initial states in SMBIOS when system boot, > then acer-wmi dirver sync this states with killswitch. By default, Acer > BIOS set the bluetooth to off. > > > 1. I have to enable the HW bluetooth switch to get the bluetooth LED > > running (USB device appears in lsusb). The acer-bluetooth SW rfkill is > > unblocked, the SW rfkill of hci0 is blocked. > > Yes, this is also right behavior, because acer-wmi driver will maintain > the killswitch status with BIOS. > > > 2. Next I have to unblock SW rfkill on hci0 by a call to `rfkill unblock > > <number of hci0>`. > > 3. Last I have to enable the HCI by the call to `hciconfig hci0 up`. > > About 2. - 3. > I thought the above behavior causes by rfkill-input reverse the hci0's > killswitch when you pressed HW bluetooth, the HW bluetooth send out a > KEY_BLUETHOOTH keycode then rfkill-input capture it to do hci0's status > reverse. > I suggest leave userland application to do killswitch, don't use > rfkill-input. > > You can do: > - Use rfkill unblock acer-bluetooth SW killswitch, don't use HW bluetooth > switch. - If you still want to use HW bluetooth switch, then I suggest > disable your rfkill-input. Have 2 way: > + Use urfkill daemon: http://www.freedesktop.org/wiki/Software/urfkill > This is a userland daemon can lock the rfkill-input to disable it > temporarily. + Direct set CONFIG_RFKILL_INPUT=N in kernel, but you will > need to rebuild kernel. After set rfkill-input disable, you need control > killswitch from userland. You can control it by rfkill tool or also try > urfkill daemon. Actually this doesn't work. When I unblock the SW switch by calling `rfkill unblock <number of acer-bluetooth>`, it unblocks the SW killswitch, the bluetooth LED goes up, the hci0 shows-up (USB device and killswitch), but initial state of hci0's killswitch is "blocked". So I still need to unblock it manually. I would preffer to don't be forced to do step 2, also for the HW switch (which should do the same job I think). Cheers, OldÅich. > > We are adding more feature in urfkill daemon, I and Gary's plan is use > urfkill daemon to replace the rfkill-input in kernel. > > > How is this supposed to work? I tried to use "rfkill.default_state=1" on > > kernel command line, but without any success. > > Yes, rfkill default_state doesn't help, because acer-wmi driver will > sync the devices status from BIOS, it's right behavior. > > > When I boot into 2.6.37, the bluetooth LED goes ON automatically and > > hciconfig shows the hci0 as UP. > > Yes, that because acer-wmi didn't sync the bluetooth status with BIOS > when system boot in 2.6.37 kernel. > > > Thanks. > > > > Best regards, > > OldÅich. > > Thank's > Joey Lee > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-acpi" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe platform-driver-x86" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
