Hi Benny, Ok, I found: In version 5 the make files in pjlib pjlib-util pjnath third_party pjmedia pjsip pjsip-apps all refer to .../../build/common.mak whereas in V7 some of them refer to $(PJDIR)/build/common.mak I think msys interprets /home/Lafras/pj relative to its install location whereas c:/mingw/bin/make.exe does not. This may have to do with the msys/mingw install/setup procedure. The first solution affects all platforms but I don't know the effect is good. In aconfigure line 2747 change ac_pjdir=`pwd' to ac_pjdir=`pwd -W` Second option is to condition the change only to mingw as follows: case $target in *mingw* | *cygw* | *win32* | *w32* ) ac_pjdir=`pwd -W` ;; *) ac_pjdir=`pwd` ;; esac Third solution (if it is a msys/mingw install issue) in ./configure test that make.exe uses the correct path and warn user that mingw is not installed properly. Regards Lafras ----- Original Message ----- From: "Benny Prijono" <bennylp@xxxxxxxxx> To: "pjsip embedded/DSP SIP discussion" <pjsip at lists.pjsip.org> Sent: Friday, September 21, 2007 5:40 PM Subject: Re: Build problem with version 7 on mingw (version 5 ok) > > Lafras Henning wrote: > > Ok I found > > > > edit C:\msys\1.0\home\Lafras\PJ\build.mak > > Line 31 change > > export PJDIR := /home/Lafras/pjt > > to > > export PJDIR := c:/msys/1.0/home/Lafras/pjt > > > > This file (build.mak) is created by the ./configure script so the > > correct fix should be in aconfigure, > > but the scriping language is beyond me. > > PJDIR is set from the output of "pwd", so I don't know what else can > we do to fix this. > > -benny > > > > Thanks > > Lafras > > > > > > ----- Original Message ----- > > *From:* Lafras Henning <mailto:lafras at xietel.com> > > *To:* pjsip at pjsip.org <mailto:pjsip at pjsip.org> > > *Sent:* Friday, September 21, 2007 8:08 AM > > *Subject:* [pjsip] Build problem with version 7 on mingw (version 5 ok) > > > > all, > > > > I use mingw on w2k. > > > > I can build version 5 of pjsip with no problem. > > > > Trying to build version 7 gives the following error: > > > > ./configure completes ok (appart from a WARNING: mswsock.h: present > > but cannot be compiled - also warned in V5 but was ok) > > make dep > > >>> > > for dir in pjlib pjlib-util pjnath third_party pjmedia pjsip > > pjsip-apps; do \ > > if c:/mingw/bin/make.exe -C $dir/build dep; then \ > > true; \ > > else \ > > exit 1; \ > > fi; \ > > done > > makefile:2: /home/Lafras/pjt/build/common.mak: No such file or directory > > c:\mingw\bin\make.exe[1]: Entering directory > > `C:/msys/1.0/home/Lafras/pjt/pjlib/build' > > c:\mingw\bin\make.exe[1]: Leaving directory > > `C:/msys/1.0/home/Lafras/pjt/pjlib/build' > > c:\mingw\bin\make.exe[1]: *** No rule to make target > > `/home/Lafras/pjt/build/common.mak'. Stop. > > c:\mingw\bin\make.exe: *** [dep] Error 1 > > <<<<< > > then stops > > > > > > The file C:/msys/1.0/home/Lafras/pjt/pjlib/build/common.mak does > > exist although the error is missing the c:/msys/1.0 part. > > > > > > Please can anyone assist. > > Regards > > Lafras > > > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip at lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >
