Richard Huxton escribió:
Linos wrote:
Richard Huxton escribió:
Linos wrote:
2009-02-27 13:51:15 CET 127.0.0.1LOG: duración: 4231.045 ms sentencia:
SELECT "nombre", "subfamilia_id", "id_familia", "hasta", "foto",
"id_seccion", "id_categoria" FROM "modelo_subfamilia"
PSQL with \timing:
-development: Time: 72,441 ms
-server: Time: 78,762 ms
but if i load it from QT or from pgadmin i get more than 4 seconds in
server and ~100ms in develoment machime, if i try the query without the
"foto" column i get 2ms in development and 30ms in server
OK, so:
1. No "foto" - both quick
2. psql + "foto" - both slow
3. QT + "foto" - slow only on server
1.No "foto" -both quick but still a noticeable
difference between them 2ms develoment - 30ms server
2. psql + "foto" -both quick really, they are about 70ms,
not bad giving that foto are bytea with small png images.
Ah, sorry - I read the psql timings as 72 thousand ms (72 seconds) - of
course you're using European decimal marks.
3. QT or WXWindows + "foto" -slow only one server yes.
The bit that puzzles me is why both are slow in #2 and not in #3.
OK - well, the fact that both psql are fast means there's nothing too
wrong with your setup. It must be something to do with the application
libraries.
After the vacuum full verbose and reindex still the same problem (i had
tried the vacuum before).
OK. Worth ruling it out.
1- The same in the two machines, tcp/ip with localhost.
Hmm...
2- I am exactly the same code in the two machines and the same pgadmin3
version too.
Good. We can rule that out.
3- Ever the entire result set.
Good.
4- I am using es_ES.UTF8 in the two machines
Good.
What can be using wxwindows and QT to access postgresql that psql it is
not using, libpq?
Well, I'm pretty sure that pgadmin will be using libpq at some level,
even if there is other code above it.
Either:
1. One machine (the fast one) is actually using unix sockets and not
tcp/ip+localhost like you think.
2. The networking setup is different on each.
3. Something your code is doing with the bytea data is slower on one
machine than another. I seem to remember that pgadmin used to be quite
slow at displaying large amounts of data. They did some work on that,
but it might be that your use-case still suffers from it.
For #1 try the psql test again, but with "-h localhost" and "-h /tmp"
(or whatever directory your unix socket is in - might be
/var/run/postgresql or similar too).
Ok, thanks for the trick now i know where to search, after trying with -h
localhost psql it is slow too in the server from 80,361 with \timing to 4259,453
using -h localhost. Any ideas what can be the problem here? i am going to make
what you suggest and capture analyze the traffic, after find the hole i have
tried in other debian server with the same kernel 2.6.26 and i have the same
problem (my development machine it is Arch Linux with 2.6.28).
Regards,
Miguel Angel.
For #2, you can always try timing "psql -h localhost ... > /dev/null" on
both machines. If you capture port 5432 with something like "tcpdump -w
ip.dump host localhost and port 5432" you can then use wireshark to see
exactly why it's slow.
For #3, I guess you'd need to reduce your code to just fetching the data
and time that. You may have already done this of course.
HTH
--
Sent via pgsql-general mailing list (pgsql-general@xxxxxxxxxxxxxx)
To make changes to your subscription:
http://www.postgresql.org/mailpref/pgsql-general
